ECO mode Lexus IS300 2005 Basic Functions / LEXUS 2005 IS300 OWNER'S MANUAL (OM53489U)

GAUGES, METERS AND SERVICE REMINDER INDICATORS
48
ODOMETER AND TRIP METER
SV13015
This meter displays the odometer and two trip meters. To
change the mode indication, push the ªODO/TRIPº knob
briefly. Each time you push the knob, the mode changes
in order from the odometer to trip meter A to trip meter B,
then back to the odometer, etc.
The odometer records the total distance the vehicle has
been driven. The twin trip meter records two different
distances independently.
For example, you can use one meter to calculate the fuel
economy and the other to measure the distance on each trip.
To set A trip meter to zero, display the A meter reading,
push the knob and hold it. The same applies for the B trip
meter.
The data of trip meters will be cancelled if the electrical power
source is disconnected.
SERVICE REMINDER INDICATORSAND WARNING BUZZERS
IF THIS INDICATOR OR
BUZZER COMES ON ...DO THIS.
(a)or
(Indicator and buzzer)
If parking brake is off,
stop immediately and
contact Lexus dealer.
(b)
(Indicator and buzzer)
Fasten driver's seat
belt
(c)Fasten front
passenger's seat belt.
(d)Take vehicle to Lexus
dealer immediately.
(e)Stop and check.
04 06.30

GAUGES, METERS AND SERVICE REMINDER INDICATORS
56
The light remains on after the ignition key is turned to ªONº.
 The light comes on with the normal driving mode while
driving.
 The light flashes.
(o)ªVSCº Warning Light (With vehicle stability
control system)
This light warns that there is a problem somewhere in the
vehicle stability control system or traction control system.
The light will come on when the ignition key is turned to the
ªONº position and will go off after a few seconds.
If the light comes on while driving, the vehicle stability control
system and traction control system do not work. However, as
conventional braking operates when applied, there is no
problem to continue your driving.
In the following cases, contact your Lexus dealer:
The light does not come on after the ignition key is turned
to the ªONº position.
 The light remains on after the ignition key is turned to the
ªONº position.
 The light comes on while driving.
The ªTRAC OFFº indicator / warning light will come on when
the ªVSCº warning light comes on even if the ªTRAC OFFº
switch is not pushed.
(p) Automatic Headlight Leveling System Warning Light
This light warns that when there is a problem somewhere in the
automatic headlight leveling system.
The light will come on when the ignition key is turned to the
ªONº position, and will go off after a few seconds.
If it comes on while driving, have your vehicle checked by your
Lexus dealer.
(q) Key Reminder Buzzer
This buzzer acts as a reminder to remove the key when you
open the driver's door with the ignition key in the ªACCº or
ªLOCKº position.
04 06.30

STEERING WHEEL AND MIRRORS
182
INSIDE REAR VIEW MIRROR
SL16013

Type A 1Day 2Night
When driving at night, pull the lever toward you to reduce
the glare from the headlights of vehicles behind you.
Before adjusting the mirror to the position with most clarity,
push the day±night change lever forward (daylight driving
position).
Remember that by reducing glare you also lose some rear view
clarity.
CAUTION
Do not adjust the mirror while the vehicle is moving.
Doing so may cause the driver to mishandle the vehicle
and an accident may occur resulting in personal death
or injuries.
SV16128

Type B
Adjust the m irror so that you can just see the rear of your
vehicle in the mirror.
Pushing the switch changes the mode between ªAUTOº
and ªDAYº.
The indicator comes on when the ªAUTOº mode is selected.
ªDAYº mode: The mirror surface is normal.
ªAUTOº mode: If the mirror detects light from the
headlights of the vehicle behind you, the mirror surface
darkens slightly to reduce the reflected light.
When the inside rear view mirror surface changes, the outside
rear view mirror surfaces will also become darker.
When the ignition key is inserted and turned on, the inside rear
view mirror always turns on in the ªAUTOº mode.
When the outside air temperature is low, it may take a little
longer for the mirror to darken in response to the detection of
headlights.
04 06.30

AIR CONDITIONING
196However, once selecting ªRECIRCULATED AIRº of the air
intake manually will make this function inoperable. In order to
make this function operable again, first select ªOUTSIDE AIRº
of the air intake, turn off the ignition switch, and start the engine
again. Then this function return to be operable.
If manual on±off of the air conditioning is desired ±
Push the ªA/Cº button to turn the air conditioning on and push
it again to turn the air conditioning off.
The air conditioning does not work if the outside temperature
is lowered down to around 0C (32F).
If the system is used for ventilation, heating in dry weather or
removing frost or exterior fog on the windshield, turn the air
conditioning off once it is no longer required. This will improve
fuel economy. The air conditioning can be used for year±round
automatic temperature control including cooling and
dehumidifying operation.
If the air conditioning compressor does not operate, the
indicator of the ªA/Cº button will blink. If the indicator of the
ªA/Cº button blinks even when the ªA/Cº button is pushed
again, have the compressor checked by your nearest Lexus
dealer.
(b) Windshield defogging and defrosting
SV21016
To remove interior fog on the windshield ±
1. Turn the air flow control dial to ªWINDSHIELDº.
2. Set the ªOUTSIDE AIRº mode.
To remove frost or exterior fog on the windshield ±
1. Turn the temperature control dial to the maximum
temperature.
2. Turn the air flow control dial to ªWINDSHIELDº.
3. Turn the fan speed control dial to ªHIº.
4. Leave the air conditioning on±off button off.
04 06.30

AIR CONDITIONING
199
SV21015
2. Remove the cover and take out the air filter
If it is dirty, it should be replaced.
INFORMATION
The air filter should be installed properly in position.The use of air conditioning with the air filter removedmay cause deteriorated dustproof performance andthen affect air conditioning performance.
(d) Operating tips
 To help cool down the interior after parking in the hot sun,
drive for the first few minutes with the windows open. After the excess heat has blown away, close the windows.
 Make sure the air inlet grilles in front of the windshield are
not blocked by leaves or other obstructions.
 If air flow control is not satisfactory, check the dashboard
vents. (See ªCenter ventsº and ªSide ventsº.)
 On humid days, do not blow cold air on the windshield. The
windshield could fog up because of the difference in air temperature on the inside and outside of the windshield.
 Keep the area under the front seats clear to allow air to
circulate throughout the vehicle.
 On cold days, set the fan speed selector to adjust the fan
speed high for a minute to help clear the intake ducts of
snow or moisture. This can reduce the amount of fogging on
the windows.
 When driving on dusty roads, close all windows. If dust
thrown up by the vehicle is still drawn into the vehicle after
closing the windows, it is recommended that the air intake
control button be left to the OUTSIDE AIR mode and the fan
speed control dial be turned to anywhere except the ªOFFº button.
 If following another vehicle on a dusty road, or driving in
windy and dusty conditions, it is recommended that the air
intake control button be temporarily pressed in to the
RECIRCULATED AIR mode, which will close off the outside
passage and prevent outside air and dust from entering the vehicle interior.
04 06.30

AUDIO
209
SV22069
In the ªTAPEº or ªCDº mode, the applicable functions are
shown in the lowest part of the display. Push the switch
just below to turn on each function.
(b) Tone and balance
How good an audio system program sounds to you is largely
determined by the mix of the treble, mid±range, and bass
levels. In fact, different kinds of music and vocal programs
usually sound better with different mixes of treble, mid±range,
and bass.
A good balance of the left and right stereo channels and of the
front and rear sound levels is also important.
Keep in mind that if you are listening to a stereo recording or
broadcast, changing the right/left balance will increase the
volume of one group of sounds while decreasing the volume
of another.
SV22070
Each time you push the ªAUDIO CONTROLº knob, the
display changes as in the following. To adjust the tone and
balance, turn the knob.
BAS: Adjusts low±pitched tones.
MID: Adjusts mid±pitched tones.
TRE: Adjusts high±pitched tones.
FADE: Adjusts the sound balance between the front and rear
speakers.
BAL: Adjusts the sound balance between the right and left
speakers.
04 06.30

AUDIO
214(d) RDS (Radio Data System)
SV22077
This function is operative at any time. Under the ªFMº mode,
ªRDSº appears on the display as long as the audio system
picks up RDS stations. When the audio system is in other than
ªFMº mode, or it can not pick up RDS stations, ªRDSº is off.
TYPE (Program type):
When you push the ªTYPE
º or ªTYPE  º button while
receiving an RDS station, the current program type appears on
the display.
If you push the ªTYPE º or ªTYPE  º button when ªRDSº is
off on the display, ªNO_PTYº appears.
Each time you push the ªTYPE º or ªTYPE º button, the
program type changes as in the following:
 ROCK
 EASY LIS (Easy listening)
 CLS/JAZZ (Classical music and jazz)
 R&B (Rhythm and Blues)
 INFORM (Information)
 RELIGION
 MISC
 ALERT (Emergency message)
TRAF (Traffic) function: A station that regularly
broadcasts traffic information is automatically located.
When you push the ªTRAFº button in the ªFMº mode, ªTRAF
SEEKº appears on the display and the radio will start seeking
any traffic program station.
If no traf fic program station is found, ªNO TRAF INFOº appears
on the display for a few seconds and the display returns to the
previous mode.
04 06.30

AUDIO
216
Cassette tape player operation
(a) Playing a cassette tape
SV22079
When you insert a cassette tape, the exposed tape should
face to the right.
The player will automatically start when you insert a cassette
tape. At this time, ªPLAYº appears on the display.
If a metal or chrome equivalent cassette tape is put in the
cassette player, the player will automatically adapt to it and
ªMTLº appears on the display.
To stop or eject the cassette tape, push the ªEJECTº button.
Auto±reverse feature: After the cassette player reaches the
end of a tape, it automatically reverses and begins to play the
other side, regardless of whether the cassette was playing or
fast forwarding.
SV22080
If a cassette is already in the slot, push the ªTA PEº button.
DolbyB Noise Reduction* feature: If you are listening
to a tape that was recorded with
Dolby  B Noise Reduction,push the ªº button. The display will indicate that the Dolby
noise reduction system is on.
The Dolby NR mode reduces tape noise by about 10 dB. For
best sound reproduction, play your tapes with this button on or
off according to the mode used for recording the tape.
To play a tape recorded without Dolby NR, push the button
again to turn off the Dolby B NR.
*: Dolby noise reduction manufactured under license from
Dolby Laboratories Licensing Corporation. ªDOLBYº and the
double D symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
04 06.30

STARTING AND DRIVING
239
Correct use of the automatic transmission is explained in
the following parts.
(a) Normal driving
(b) Driving in M mode
(c) Using engine braking
(d) Using the ª3º, ª2º and ªLº positions
(e) Backing up
(f) Parking
(g) Good driving practice
(h) If you cannot shift the selector lever
(i) If the ªECT PWRº indicator light flashes
(a) Normal driving
SV31021

1ªPº (Park) position 2ªNº (Neutral) position
1. Start the engine as instructed in ªHow to start the
engineº on page 237.
The transmission must be in ªPº or ªNº. The engine will not sta\
rt
in any drive position even if the ignition key is turned to
ªSTARTº.
CAUTION
The selector lever knob can become extremely hot after
parking under the sun.
04 06.30

STARTING AND DRIVING
240
SS31019

1Power position 2Normal position
3Snow position
2. Set the driving pattern selector switch to the ªNormalº
position.
Your transmission has a driving pattern selector switch which
allows you to select ªPowerº, ªNormalº or ªSnowº mode \
to suit
your driving condition. For ordinary driving, Lexus
recommends that you use the ªNormalº position to improve fuel
economy.
3. For more powerful acceleration and sporty driving, use
the ªPowerº position.
In the ªPowerº position, the ªECT PWRº light in the instrument\
cluster is on and the transmission is shifted up at higher vehicle
speeds and shifted down more responsively than in the
ªNormalº position.
For ªSnowº mode, see ªElectronic Throttle Control
Systemº on page 260.
SV31022

1Brake pedal 2ªDº (Drive) position
4. With your foot holding down the brake pedal, shift the
selector lever to ªDº.
Always use the ªDº position to improve fuel economy and quiet
driving. In this position, shifting into the overdrive gear is
possible. However, while the engine coolant temperature is
low, the transmission will not shift into the overdrive gear even
in the ªDº position. (See ª(c) Using engine brakingº and \
ª(g)
Good driving practiceº for exceptions.)
CAUTION
Never put your foot on the accelerator pedal while
shifting.
04 06.30