navigation system Lexus IS300h 2014 Navigation manual

184
IS300h/250_Navi_EE
6. TIPS FOR THE NAVIGATION SYSTEM
1. GPS (GLOBAL POSITIONING SYSTEM)
The Global Positioning System (GPS) de-
veloped and operated by the U.S. Depart-
ment of Defense provides an accurate
current position, normally using 4 or more
satellites, and in some case 3 satellites. The
GPS system has a certain level of inaccura-
cy. While the navigation system compen-
sates for this most of the time, occasional
positioning errors of up to 100 yd. (100 m)
can and should be expected. Generally, po-
sition errors will be corrected within a few
seconds.When the vehicle is receiving signals from
satellites, the “GPS” mark appears at the
top left of the screen.
The GPS signal may be physically obstruct-
ed, leading to inaccurate vehicle position on
the map screen. Tunnels, tall buildings,
trucks, or even the placement of objects on
the instrument panel may obstruct the GPS
signals.
The GPS satellites may not send signals due
to repairs or improvements being made to
them.
Even when the navigation system is receiv-
ing clear GPS signals, the vehicle position
may not be shown accurately or inappropri-
ate route guidance may occur in some cas-
es.
LIMITATIONS OF THE
NAVIGATION SYSTEM
This navigation system calculates the
current position using satellite signals,
various vehicle signals, map data, etc.
However, an accurate position may not
be shown depending on satellite condi-
tions, road configuration, vehicle condi-
tion or other circumstances.
NOTICE
●The installation of window tinting may
obstruct the GPS signals. Most window
tinting contains some metallic content
that will interfere with GPS signal recep-
tion of the antenna in the instrument
panel. We advise against the use of win-
dow tinting on vehicles equipped with
navigation systems.
IS_Navi_EE_53C71E.book 184 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

185
6. TIPS FOR THE NAVIGATION SYSTEM
IS300h/250_Navi_EE
NAVIGATION SYSTEM
3
zAccurate current position may not be
shown in the following cases:
• When driving on a small angled Y-shaped
road.
• When driving on a winding road.
• When driving on a slippery road such as
in sand, gravel, snow, etc.
• When driving on a long straight road.
• When motorway and surface streets run
in parallel.
• After moving by ferry or vehicle carrier.
• When a long route is searched during
high speed driving.
• When driving without setting the current
position calibration correctly.
• After repeating a change of direction by
going forward and backward, or turning
on a turntable in a parking lot.
• When leaving a covered parking lot or
parking garage.
• When a roof carrier is installed.
• When driving with tyre chains installed.
• When the tyres are worn.
• After replacing a tyre or tyres.
• When using tyres that are smaller or
larger than the factory specifications.
• When the tyre pressure in any of the 4
tyres is not correct.zInappropriate route guidance may occur in
the following cases:
• When turning at an intersection off the
designated route guidance.
• If you set more than 1 destination but skip
any of them, auto reroute will display a
route returning to the destination on the
previous route.
• When turning at an intersection for which
there is no route guidance.
• When passing through an intersection for
which there is no route guidance.
• During auto reroute, the route guidance
may not be available for the next turn to
the right or left.
• During high speed driving, it may take a
long time for auto reroute to operate. In
auto reroute, a detour route may be
shown.
• After auto reroute, the route may not be
changed.
• If an unnecessary U-turn is shown or
announced.
• If a location has multiple names and the
system announces 1 or more of them.
• When a route cannot be searched.
• If the route to your destination includes
gravel, unpaved roads or alleys, the route
guidance may not be shown.
zIf the vehicle cannot receive GPS signals,
the current position can be adjusted
manually. (→P.1 7 3 )
IS_Navi_EE_53C71E.book 185 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

186
6. TIPS FOR THE NAVIGATION SYSTEM
IS300h/250_Navi_EE
• Your destination point might be shown on
the opposite side of the street.
• When a portion of the route has regula-
tions prohibiting the entry of the vehicle
that vary by time, season or other reasons.
• The road and map data stored in the navi-
gation system may not be complete or
may not be the latest version.
zAfter replacing a tyre: →P.1 74
INFORMATION
●
This navigation system uses tyre turning
data and is designed to work with factory-
specified tyres for the vehicle. Installing
tyres that are larger or smaller than the
originally equipped diameter may cause
inaccurate display of the current position.
The tyre pressure also affects the diame-
ter of the tyres, so make sure that the tyre
pressure of all 4 tyres is correct.
IS_Navi_EE_53C71E.book 186 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

187
6. TIPS FOR THE NAVIGATION SYSTEM
IS300h/250_Navi_EE
NAVIGATION SYSTEM
3
2. MAP DATABASE VERSION AND COVERED AREA
1Press the “MENU” button on the
Remote Touch.
2Select “Setup”.
3Select “Navigation”.
4Select “Map data”.
5Check that the map data screen is dis-
played.
MAP DATA
Coverage areas and legal information
can be displayed.
No.Function
Map version
Select to display legal information.
Select to display map data coverage
areas.
INFORMATION
●
Map data updates are available for a fee.
Contact your Lexus dealer for further
information.
IS_Navi_EE_53C71E.book 187 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

188
6. TIPS FOR THE NAVIGATION SYSTEM
IS300h/250_Navi_EE
ABOUT THE MAP DATA
Map data for the navigation system is
contained in a SD card that is inserted in
the SD card slot located at the bottom of
the audio control panel.
Do not eject the SD card, as doing so
may deactivate the navigation system.
NOTICE
●Do not edit or delete the map data on the
SD card, as doing so may deactivate the
navigation system.
INFORMATION
●
microSDHC Logo is a trademark of SD-
3C,LLC.
IS_Navi_EE_53C71E.book 188 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

189
6. TIPS FOR THE NAVIGATION SYSTEM
IS300h/250_Navi_EE
NAVIGATION SYSTEM
3
IS_Navi_EE_53C71E.book 189 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

277
1. SPEECH COMMAND SYSTEM OPERATION
SPEECH COMMAND SYSTEM
IS300h/250_Navi_EE
5
1Press the talk switch.
2Say “Go home” or select “Go home”.
zA confirmation screen will be displayed
showing the recognition results.
3Say “Yes” or select “Yes”.
zThe system starts searching for a route to
your home.
zWhen the speech command is recognized,
the map of the area around the home
address will be displayed and route guid-
ance to the home address will begin.
INFORMATION
●
If the system does not respond or the
confirmation screen does not disappear,
press the talk switch and try again.
●If a speech command cannot be recog-
nized, voice guidance will say “Pardon?”
and speech command reception will
restart.
●If a speech command cannot be recog-
nized 2 consecutive times, the speech
command guidance system will say “To
restart voice recognition, push the talk
switch.”. Then voice recognition will be
suspended.
●The voice recognition prompt can be set
to on or off when “Voice prompts” is
selected. This setting can also be
changed on the “Voice settings” screen.
(→P. 8 4 )
●Voice guidance can be canceled by set-
ting voice prompts to off. Use this setting
when it is desirable to say a command
immediately after pressing the talk switch
and hearing a beep.
SPEECH COMMAND
EXAMPLE: SEARCHING FOR
A ROUTE TO YOUR HOME*
zIf a home address is not registered, voice
guidance will say “Your home is not set.”.
Please try again after setting a home
location. (→P.151)
*: With navigation function
IS_Navi_EE_53C71E.book 277 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

278
1. SPEECH COMMAND SYSTEM OPERATION
IS300h/250_Navi_EE
1Press the talk switch.
2Say “Enter an address” or select “Enter
an address”.
zThe searchable countries are restricted
according to the voice recognition lan-
guage.
zSome areas cannot be recognized by the
voice recognition system.
XFor UK English and French
3Say “”, “”
and “” continuously.
XExcept for UK English and French
3Say “”, “”
and “” continuously.
zSay the desired house number in the place
of the “<>”. It is possible to only say the num-
bers. For example, 1,2,3,4 etc. (It is not pos-
sible to say cardinals.) Inputting the house
number can be skipped.
zSay the desired full street name that
belongs to the set country in the place of
the “<>”. If only the city name was said at
step 3, say the street name. If the street
name is not unique, select the appropriate
number from the displayed address list.
zSay the desired city name or city name and
street name that belongs to the set country
in the place of the “<>”. Not just the city
name, but the city name and street name
can be said at the same time. If both are
said at the same time and the street name is
not unique, select the appropriate number
from the displayed address list.
SPEECH COMMAND
EXAMPLE: PERFORMING A
DESTINATION SEARCH BY
ADDRESS*
Use the official language of the country
the desired destination is in. A destina-
tion search by address, using speech
command, can only be performed for
countries that have one of the following
15 languages as their official language.
· Dutch
· French
· German
· Italian
· Spanish
· UK English
· Russian
· Portuguese
· Swedish
· Danish
· Finnish
· Greek
· Polish
· Turkish
· Czech
For changing voice recognition lan-
guages: →P.75
*: With navigation function
IS_Navi_EE_53C71E.book 278 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

282
1. SPEECH COMMAND SYSTEM OPERATION
IS300h/250_Navi_EE
2. COMMAND LIST
zFrequently used commands are listed in the following tables.
zFor devices that are not installed in the vehicle, the related commands will not be dis-
played in the “Shortcuts” screen. Also, according to conditions, other commands may
not be displayed in the “Shortcuts” screen.
zThe functions available may vary according to the system installed.
zCommands that have “O” in the shortcuts menu column can be recognized from the
“Shortcuts” screen.
XBasic
XNavi*
1
*1: With navigation function
*2: For example; “Restaurant”, “Hospital” etc.
Recognizable speech commands and their actions are shown below.
zVoice recognition language can be changed. (→P. 7 5 )
CommandAction
“Help”Prompts voice guidance to offer examples of commands
and operation methods
“Go back”Returns to the previous screen
CommandActionShortcuts
menu
“Find nearby ”Displays a list of near the cur-
rent positionO
“Enter an address”Enables setting a destination by saying the ad-
dressO
“Go home”Displays the route to homeO
IS_Navi_EE_53C71E.book 282 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

329
1. TELEPHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
IS300h/250_Navi_EE
TELEPHONE
7
3. CALLING ON THE Bluetooth® PHONE
1Press the “MENU” button on the
Remote Touch.
2Select “Telephone”.
3Select the desired button to call from.
zThe telephone top screen can be displayed
by pressing the switch on the steering
wheel.
*: With navigation function
After a Bluetooth® phone has been reg-
istered, a call can be made using the
hands-free system. There are several
methods by which a call can be made, as
described below.
How to make a call listPage
By favourites list330
By call history330
By contacts list332
By dial pad33 4
By e-mail/SMS/MMS345
By POI call*107
SOS335
By off hook switch335
By speech command system280
IS_Navi_EE_53C71E.book 329 ページ ２０１４年５月２９日　木曜日　午前１１時２２分