fuel lexus LC500 2018 User Guide

68
-$@-$I@0.@0.&@ &&

1-3. Hybrid system
There are air intake vents under the
rear seats for the purpose of cooling
the hybrid battery (traction battery). If
the vents become blocked, the hybrid
battery input and output may be
restricted, leading to a reduction in
hybrid battery (traction battery) out-
put.
When a certain level of impact is
detected by the impact sensor, the
emergency shut off system blocks the
high voltage current and stops the fuel
pump to minimize the risk of electrocu-
tion and fuel leakage. If the emergency
shut off system activates, your vehicle
will not restart. To restart the hybrid
system, contact any authorized Lexus
retailer or Lexus authorized repairer,
or any reliable repairer.
A message is automatically displayed
when a malfunction occurs in the
hybrid system or an improper opera-
tion is attempted.
If a warning message is shown on the
multi-information display, read the
NOTICE
■Hybrid battery (traction battery)
Do not carry large amounts of water
such as water cooler bottles in the vehi- cle. If water spills onto the hybrid battery (traction battery), the battery may be
damaged. Have the vehicle inspected by any authorized Lexu s retailer or Lexus authorized repairer, or any reliable
repairer.
Hybrid battery (traction bat-
tery) air intake vents
NOTICE
■Hybrid battery (traction battery) air intake vents
●Make sure not to block the air intake vents with anything, such as a seat cover, plastic cover, or luggage. If the
vents become blocked, the hybrid bat- tery (traction battery) input and output may be restricted, leading to a reduc-
tion in hybrid battery (traction battery) output and a malfunction.
●When dust etc. has accumulated in the air intake vents, periodically clean
them with a vacuum cleaner to prevent the vents from clogging.
●Filters are installed to the air intake vents. When the filters remain notice-
ably dirty even after cleaning the air intake vents, filter cleaning or replace-ment is recommended. When clean-
ing or replacing the filters, contact any authorized Lexus retailer or Lexus authorized repairer, or any reliable
repairer. Refer to P.309 for details on how to clean the filters.
●Do not get water or foreign materials
in the air intake vents as this may cause a short circuit and damage the hybrid battery (traction battery).
Emergency shut off system
Hybrid warning message

83
2
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
Vehicle status information and indicators
Warning lights inform the driver of mal-
functions in the indicated vehicle sys-
tems.
*1: These lights turn on when the engine
switch is turned to
IGNITION ON mode to
indicate that a system check is being
performed. They will turn off after the
engine is started, or
after a few seconds. There may be a
malfunction in a syst em if a light does
not come on, or turn off. Have the vehi-
cle inspected by any authorized Lexus
retailer or Lexus authorized repairer, or
any reliable repairer.
*2: This light illuminates on the multi-infor-
mation display.
*3: The light flashes to indicate a malfunc-
tion.
*4: This light illuminates on the center
Warning lights
(red)
Brake system warning light*1
( P.368)
Charging system warning
light*2 ( P.368)
Low engine oil pressure
warning light*2 ( P.368)
Malfunction indicator lamp*1
( P.369)
SRS warning light*1
( P.369)
ABS warning light*1
( P.369)
(red)
Electric power steering sys-
tem warning light*1 ( P.370)
(yellow)
Electric power steering sys-
tem warning light*1 ( P.370)
PCS warning light*1, 3
( P.370)
(orange)
LKA indicator*2 (P.371)
Slip indicator*1 ( P.371)
Brake Override System
warning light*2
( P.372)/Drive-Start Con-
trol warning light*2 ( P.372)
Brake hold operated indica-
tor*1, 3 ( P.372)
Parking brake indicator*3
(P.372)
Brake pad wear warning
light*2 ( P.373)
(yellow)
Brake system warning light*1
(P.373)
Low fuel level warning light
( P.373)
Driver’s and front passen-
ger’s seat belt reminder light
( P.373)
Rear passengers’ seat belt
reminder lights*4 ( P.374)
Master warning light*1
( P.374)
Tire pressure warning light*1, 3
( P.374)
High coolant temperature
warning light*2 ( P.375)

89
2
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
Vehicle status information and indicators
Outside temperature
Displays the outside temperature within the range of -40°C (-40°F) to 50°C (122°F)
Low outside temperature indicator comes on when the ambient temperature is 3°C (37°F)
or lower
Tachometer
Displays the engine speed in revolutions per minute
Speedometer
Shift position/shift range/gear position ( P.173, 179)
Shift position indicator ( P.175, 181)
Clock
Time displayed is linked to the analog clock on the instrument panel. (P.297)
Engine coolant temperature gauge
Displays the engine coolant temperature
If the engine coolant temperature gauge indi cator enters the red zone, a buzzer sounds
and the high coolant temperature warning light comes on
Odometer and trip meter display
Odometer:
Displays the total distance the vehicle has been driven
Trip meter:
Displays the distance the vehicle has been driven since the meter was last reset
Trip meters “A” and “B” can be used to record and display different distances independently
Fuel gauge
Displays the quantity of fuel remaining in the tank
Multi-information display
Presents the driver with a variety of vehicle data (P.92)
Displays warning messages in case of a malfunction (P.378)
Motor power display/Hybrid System Indicator (LC500h)
Displays the motor power display (P.87) or Hybrid System Indicator (P.86)
■Speed warning
When the vehicle reaches the set
speed, the speed warning display will
flash.
This setting can be enabled on the
multi-information display. ( P.92)
Always observe the legal speed limit when
driving on public roads.
■Rev indicator
When the engine reaches a set speed
or the red zone, a ring-shaped indica-
tor will be displayed on the tachometer.
B
C
D
E
F
G
H
I
J
K
L

94
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
■Content of drive information
Select to display various drive data.
Up to 2 of the following items can be
selected.
Items displayed can be switched by
pressing or of the meter con-
trol switches to select and pressing
or .
 Current fuel consumption*1
Displays the current rate of fuel consump-
tion
 Average fuel economy (after
reset*2/after start/after refuel)*1
Displays the average fuel consumption
since the function was reset, the engine
was started, and the vehi-
cle was refueled, respectively
Use the displayed average fuel consump-
tion as a reference.
 Average speed (after reset*2/after
start)*1
Displays the average vehicle speed since
the function was reset and the engine
was started, respectively
 Elapsed time (after reset*2/after
start)*1
Displays the elapsed time since the func-
tion was reset and the engine tem> was started, respectively
 Distance (range/after start)*1
Displays the estimated maximum distance
that can be driven with the quantity of fuel
remaining and the distance driven after the
engine was started
respectively.
• This distance is computed based on your
average fuel consumption. As a result,
the actual distance that can be driven
may differ from that displayed.
• When only a small amount of fuel is
added to the tank, the display may not be
updated.
When refueling, turn the engine switch
off. If the vehicle is refu-
eled without turning the engine switch
off, the display may not
be updated.
*1: Displayed when the item is set in “Drive
Info 1” and “Drive Info 2”.
*2: The function can be reset by pressing
“OK” of the meter control switches for
longer than 1 second when the item to
reset is displayed.
If there is more than one item that can
be reset, the item selection screen will
appear.
■Eco Driving Indicator/engine oil
temperature gauge (LC500)
 P.86, 88
■Hybrid System Indicator/motor
power display (LC500h)
 P.86
■Energy monitor (LC500h)
 P.104
■Tire pressure
 P.329
■Gear positions
Displays the current shift range or gear
position when the shift position is in D
Drive information

96
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
speed, the display may not show the actual
condition of the vehicle.
 Switching the display
To switch to advanced display, press “OK”.
To return to normal display, press “OK”.
 Resetting the record of maximum
G-forces
With the record of maximum G-forces dis-
played, press and hold “OK” to reset the
display.
 Peak hold function (advanced dis-
play only)
If lateral G-forces of 0.5 G or greater are
generated, the G-force value displayed on
the main meter will turn yellow and be held
for 3 seconds.
■Rear wing position (if equipped)
Displays the raised/retracted state of
the active rear wing
■LKA (Lane-Keeping Assist) vehicle
sway warning (if equipped)
 P.219
■Display off
A blank screen is displayed
Select to display the following naviga-
tion system-linked information.
 Route guidance
 Compass display
Select to enable selection of an audio
source etc. on the meter using the
meter control switches.
Select to display the dynamic radar
cruise control with full-speed range
( P.229)/LKA (Lane-Keeping
Assist) ( P.218) information, when
the system is used.
Select to display warning messages
and measures to be taken if a malfunc-
tion is detected. ( P.378)
Select to change the meter display set-
tings.
■Language
Select to change the language on the
display.
■Units
Select to change the unit of measure
for fuel consumption.
Navigation sys tem-linked dis-
play (if equipped)
Audio system-linked display
Driving assist system information
Warning message display
Settings display

104
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
*: If equipped
Multi-information display
Center Display
Meter control switches
“MENU” button
Touchpad
Center Display
Press the “MENU” button on the Remote Touch, then select on the menu
screen.
If the “Trip information” or “History” screen is displayed, select “Energy”.
Multi-information display
Press or of the meter control switches and select , and then press or
to select the energy monitor display.
Energy monitor*/consump-
tion screen
You can view the status of your
hybrid system (LC500h) and fuel
consumption information on the
multi-information display and Cen-
ter Display.
The energy monitor or consump-
tion screen can be displayed on the
side display.
System components
A
B
C
D
E
Energy monitor (LC500h)

107
2
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
Vehicle status information and indicators
High
Multi-information display
Low
High
These images are examples only, and may
vary slightly from actual conditions.
Press the “MENU” button on the
Remote Touch, then select on the
menu screen, and then select “Trip
information” or “History”.
■Trip information
If a screen other than “Trip information”
is displayed, select “Trip information”.
Resetting the consumption data
Fuel consumption in the past 15
minutes
Current fuel consumption
Regenerated energy in the past 15
minutes (LC500h)
One symbol indicates 50 Wh. Up to 5
symbols are shown.
Average vehicle speed since the
engine was started.
Elapsed time since the engine
was started.
Cruising range
Average fuel consumption for the past 15
minutes is divided by color into past aver-
ages and averages attained since the
engine switch was last
turned to IGNITION ON mode mode>. Use the displayed average fuel
consumption as a reference.
The image is an example only, and may
vary slightly from actual conditions.
■History
If a screen other than “History” is dis-
played, select “History”.
Best recorded fuel consumption
Latest fuel consumption
Previous fuel consumption record
Resetting the History data
Updating the latest fuel consump-
Consumption
B
A
B
A
B
C
D
E
F
G
A
B
C
D
E

108
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
tion data
The latest fuel consumption history is
divided by color into past averages and the
average fuel consumption since the last
updated. Use the displayed average fuel
consumption as a reference.
The image is an example only, and may
vary slightly from actual conditions.
■Updating the History data
Update the latest fuel consumption by selecting “Clip” to measure the current fuel consumption again.
■Resetting the data
The fuel consumption data can be deleted
by selecting “Clear”.
■Cruising range
Displays the estimated maximum distance
that can be driven with the quantity of fuel remaining.
This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ
from that displayed.
Display the vehicle information on the
side display ( P.277) and then select
or to display the desired
screen.
■Trip information (type A)
Displays the average fuel consumption
and regenerated energy for the past 10
minutes in 1 minute intervals
(LC500h), as well as the cruising
range.
The image is an example only, and may
vary slightly from actual conditions.
Use the displayed average fuel consump-
tion as a reference.
■Trip information (type B)
Displays the cruising range, latest fuel
consumption and the amount of time
elapsed since the engine tem> was started.
The image is an example only, and may
vary slightly from actual conditions.
Use the displayed average fuel consump-
tion as a reference.
■History
Displays the average fuel consumption
and highest fuel consumption.
Using the side display

109
2
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
Vehicle status information and indicators
The image is an example only, and may
vary slightly from actual conditions.
Use the displayed average fuel consump-
tion as a reference.
■Energy monitor (LC500h)
Displays the hybrid system operation
and energy recovery states.
Displayed content is the same as that
displayed on the multi-information dis-
play. ( P.104)
The image is an example only, and may
vary slightly from actual conditions.

4
153
-$@-$I@0.@0.&@ &&

4
Driving
Driving
4-1. Before driving
Driving the vehicle..................... 154
Cargo and luggage .................... 161
Trailer towing ............................... 162
4-2. Driving procedures
Engine (ignition) switch (LC500)
......................................................... 163
Power (ignition) switch (LC500h)
......................................................... 167
EV drive mode (LC500h)...... 171
Automatic transmission (LC500)
......................................................... 173
Hybrid transmission (LC500h)
......................................................... 179
Turn signal lever ......................... 186
Parking brake .............................. 187
Brake Hold.................................... 189
4-3. Operating the lights and wipers
Headlight switch .......................... 191
Automatic High Beam ............. 193
Fog light switch ........................... 196
Windshield wipers and washer
......................................................... 196
4-4. Refueling
Opening the fuel tank cap...... 201
4-5. Using the driving support sys-
tems
Lexus Safety System+ ............. 203
PCS (Pre-Collision System) . 210
LKA (Lane-Keeping Assist) .. 218
RSA (Road Sign Assist).......... 226
Dynamic radar cruise control with
full-speed range ...................... 229
Cruise control ............................ 239
Driving mode select switch ... 242
Lexus parking assist-sensor .. 243
BSM (Blind Spot Monitor) .... 248
Active rear wing ........................ 259
Driving assist systems .............. 262
4-6. Driving tips
Hybrid vehicle driving tips
(LC500h).................................. 267
Winter driving tips .................... 269