headlight lexus LC500 2018 User Guide

193
4
-$@-$I@0.@0.&@ &&

4-3. Operating the lights and wipers
Driving
Pull the lever toward you and release it
again to turn off the lights.
When any of the following conditions is
met, while the headlights (low beam)
are on, the cornering lights will addi-
tionally turn on and light up the direc-
tion of movement for the vehicle. This is
to ensure excellent visibility when
either driving at intersections or park-
ing at night.
 The steering wheel is operated
 The turn signal lever is operated
 The shift position is in R (both left
and right side cornering lights)
■Cornering light control
●The lights illuminate when the vehicle speed is approximately 30 km/h (19
mph) or less. However, the lights turn off when the vehicle speed increases to approximately 35 km/h (22 mph) or
more.
●After the lights remain illuminated for 30
minutes, they automatically turn off.
*:If equipped
1 Push the lever away from you with
the headlight switch in the or
position.
2 Press the Automatic High Beam
switch.
Cornering lights
Automatic High Beam*
The Automatic High Beam uses an
in-vehicle camera sensor to assess
the brightness of streetlights, the
lights of a vehicle ahead, etc., and
automatically turns the high beam
on or off as necessary.
WARNING
■Limitations of the Automatic High Beam
Do not rely on the Automatic High Beam. Always drive safely, taking care to observe your surroundings and turning
the high beam on or off manually if nec- essary.
■To prevent incorrect operation of the Automatic High Beam system
Do not overload the vehicle.
Activating the Automatic High
Beam system

194
-$@-$I@0.@0.&@ &&

4-3. Operating the lights and wipers
The Automatic High Beam indicator will come on when the headlights are turned on automatically to indicate that the system
is active.
■High beam automatic turning on or off
conditions
●When all of the following conditions are
met, the high beam will be automatically turned on (after approximately 1 second):• Vehicle speed is above approximately 40
km/h (25 mph). • The area ahead of the vehicle is dark.• There are no vehicles ahead with head-
lights or tail lights turned on. • There are few streetlights on the road ahead.
●If any of the following conditions are met, the high beam will be automatically
turned off: • Vehicle speed drops below approxi-mately 30 km/h (19 mph).
• The area ahead of the vehicle is not dark. • Vehicles ahead have headlights or tail lights turned on.
• There are many streetlights on the road ahead.
■Camera sensor detection information
●The high beam may not be automatically turned off in the following situations:• When oncoming vehicles suddenly
appear from a curve • When the vehicle is cut in front of by another vehicle
• When vehicles ahead are hidden from sight due to repeated curves, road divid-ers or roadside trees
• When vehicles ahead appear from the faraway lane on wide road
• When vehicles ahead have no lights
●The high beam may be turned off if a
vehicle ahead that is using fog lights with- out using the headlights is detected.
●House lights, street lights, traffic signals, and illuminated billboards or signs may cause the high beam to switch to the low
beams, or the low beams to remain on.
●The following factors may affect the
amount of time taken to turn the high beam on or off:• The brightness of headlights, fog lights,
and tail lights of vehicles ahead • The movement and direction of vehicles ahead
• When a vehicle ahead only has opera- tional lights on one side• When a vehicle ahead is a two-wheeled
vehicle • The condition of the road (gradient, curve, condition of the road surface etc.)
• The number of passengers and amount of luggage
●The high beam may be turned on or off when the driver does not expect it.
●Bicycles or similar objects may not be detected.
●In the situations shown below, the system may not be able to accurately detect sur-
rounding brightness levels. This may cause the low beams to remain on or the high beams to cause problems for pedes-
trians, vehicles ahead or other parties. In these cases, manually switch between the high and low beams.
• In bad weather (rain, snow, fog, sand- storms etc.)• The windshield is obscured by fog, mist,
ice, dirt etc. • The windshield is cracked or damaged.• The camera sensor is deformed or dirty.
• Surrounding brightness levels are equal to those of headlights, tail lights or fog lights.
• Vehicles ahead have headlights or tail lights that are either switched off, dirty, changing color, or have improperly
adjusted aim. • When driving through an area of inter-mittently changing brightness and dark-

195
4
-$@-$I@0.@0.&@ &&

4-3. Operating the lights and wipers
Driving
ness. • When frequently and repeatedly driving ascending/descending roads, or roads
with rough, bumpy or uneven surfaces (such as stone-paved roads, gravel tracks etc.).
• When frequently and repeatedly taking curves or driving on a winding road.• There is a highly reflective object ahead
of the vehicle, such as a sign or a mirror. • The vehicle’s headlights are damaged or dirty.
• The vehicle is listing or titling, due to a flat tire, a trailer being towed etc.• The driver believes that the high beam
may be causing problems or distress to other drivers or pedestrians nearby.• The vehicle is used in a territory in which
vehicles travel on the opposite side of the road of the country for which the vehicle is approved, for example using a vehicle
designed for right-hand traffic in a left- hand traffic territory, or vice versa.
■Switching to low beam
Pull the lever to the original position.
The Automatic High Beam indicator will
turn off.
Push the lever away from you to activate
the Automatic High Beam system again.
■Switching to high beam
Press the Automatic High Beam
switch.
The Automatic High Beam indicator will
turn off and the high beam indicator will
turn on.
Press the switch to activate the Automatic
High Beam system again.
Turning the high beam on/off
manually

196
-$@-$I@0.@0.&@ &&

4-3. Operating the lights and wipers
Turns the rear fog light on
Releasing the switch ring returns it to .
Operating the switch ring again turns the
rear fog light off.
■Rear fog light can be used when
The headlights are turned on.
Each time the headlights are turned off, the rear fog light is turned off.
Operate the lever and switch as fol-
lows to use the wipers. When AUTO is
selected, the wipers will operate auto-
matically when the sensor detects fall-
ing rain. The system automatically
adjusts wiper timing in accordance
with rain volume and vehicle speed.
Fog light switch
When in difficult driving conditions,
such as in rain and fog, turn on the
rear fog light to notify following
vehicles the existence of your vehi-
cle.
Turning on the rear fog light
Windshield wipers and
washer
Operating the lever can switch
between automatic operation and
manual operation, or can use the
washer.
NOTICE
■When the windshield is dry
Do not use the wipers, as they may dam-
age the windshield.
Operating the wiper lever

197
4
-$@-$I@0.@0.&@ &&

4-3. Operating the lights and wipers
Driving
1 Off
2 Rain-sensing operation
3 Low speed operation
4 High speed operation
5 Temporary operation
When AUTO is selected, the sensor
sensitivity can be adjusted by turning
the switch ring.
6 Increases the sensitivity
7 Decreases the sensitivity
8 Washer/wiper dual operation
The wipers will automatically operate a
couple of times after the washer squirts.
(After operating several times, the wipers
operate once more time after a short delay
to prevent dripping. However, the dripping
prevention does not operate while the
vehicle is moving.)
When the engine switch is
in IGNITION ON mode and
the headlights are on, if the lever is pulled,
the headlight cleaners will operate once.
After this, the headlight cleaners will oper-
ate every 5th time the lever is pulled.
■The windshield wiper and washer can be
operated when
The engine switch

is in
IGNITION ON mode .
■Raindrop sensor
●The raindrop sensor judges the amount
of raindrops. An optical sensor is adopted. It may not operate properly when sunlight from the
rising or setting of the sun intermittently strikes the windshield, or if bugs etc. are present on the windshield.
●If the wiper is turned to AUTO position while the engine switch is
in IGNITION ON mode , the wipers will operate once to show that AUTO mode is activated.
●If the temperature of the raindrop sensor is 85°C (185°F) or higher, or -30°C (-
22°F) or lower, automatic operation may not occur. In this case, operate the wipers in any mode other than AUTO.
■If no windshield washer fluid sprays
Check that the washer nozzles are not blocked if there is washer fluid in the wind-
shield washer fluid reservoir.

209
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
WARNING
●If the part of the windshield in front of the camera sensor is fogged up or covered with condensation or ice, use
the windshield defogger to remove the fog, condensation or ice. ( P.281)
●If water droplets cannot be properly removed from the area of the wind-
shield in front of the camera sensor by the windshield wipers, replace the wiper insert or wiper blade.
If the wiper inserts or wiper blades need to be replaced, contact any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer.
●Do not attach window tinting to the windshield.
●Replace the windshield if it is damaged
or cracked. If the windshield needs to be replaced, contact any authorized Lexus retailer
or Lexus authorized repairer, or any reliable repairer.
●Do not get the camera sensor wet.
●Do not allow bright lights to shine into the camera sensor.
●Do not dirty or damage the camera
sensor. When cleaning the inside of the wind-shield, do not allow glass cleaner to
contact the lens. Also, do not touch the lens. If the lens is dirty or damaged, contact
any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer.
●Do not subject the camera sensor to a
strong impact.
●Do not change the installation position or direction of the camera sensor or remove it.
●Do not disassemble the camera sen-
sor.
●Do not install an electronic device or device that emits strong electric waves
near the camera sensor.
●Do not modify any components of the vehicle around the camera sensor (inside rear view mirror, etc.) or ceiling.
●Do not attach any accessories that
may obstruct the camera sensor to the hood, front grille or front bumper. Contact any authorized Lexus retailer
or Lexus authorized repairer, or any reliable repairer for details.
●If a surfboard or other long object is to be mounted on the roof, make sure
that it will not obstruct the camera sen- sor.
●Do not modify the headlights or other lights.

216
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
cle • When approaching the side or front of a vehicle
• If a preceding vehicle has a small rear end, such as an unloaded truck• If a preceding vehicle has a low rear end,
such as a low bed trailer
• If a vehicle ahead is carrying a load which
protrudes past its rear bumper • If a vehicle ahead has extremely high ground clearance
• If a vehicle ahead is irregularly shaped, such as a tractor or side car
• If the sun or other light is shining directly on a vehicle ahead
• If a vehicle cuts in front of your vehicle or emerges from beside a vehicle• If a vehicle ahead makes an abrupt
maneuver (such as sudden swerving, acceleration or deceleration)• When suddenly cutting behind a preced-
ing vehicle • When a vehicle ahead is not directly in front of your vehicle
• When driving in inclement weather such as heavy rain, fog, snow or a sandstorm• When the vehicle is hit by water, snow,
dust, etc. from a vehicle ahead • When driving through steam or smoke• When driving in a place where the sur-
rounding brightness changes suddenly, such as at the entrance or exit of a tunnel• When a very bright light, such as the sun
or the headlights of oncoming traffic, shines directly into the camera sensor• When the surrounding area is dim, such
as at dawn or dusk, or while at night or in a tunnel• After the engine has
started the vehicle has not been driven for a certain amount of time• While making a left/right turn and for a
few seconds after maki ng a left/right turn • While driving on a curve and for a few seconds after driving on a curve
• If your vehicle is skidding • If the front of the vehicle is raised or low-ered
• If the wheels are misaligned
• If a wiper blade is blocking the camera sensor• The vehicle is wobbling.
• The vehicle is being driven at extremely high speeds.• When driving on a hill
• If the radar sensor or camera sensor is misaligned
●In some situations such as the following, sufficient braking force may not be obtained, preventing the system from
performing properly: • If the braking functions cannot operate to their full extent, such as when the brake
parts are extremely cold, extremely hot, or wet• If the vehicle is not properly maintained
(brakes or tires are excessively worn,

220
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
WARNING
■Before using LKA system
Do not rely solely upon the LKA system. The LKA system does not automatically
drive the vehicle or reduce the amount of attention that must be paid to the area in front of the vehicle. The driver must
always assume full responsibility for driv- ing safely by paying careful attention to the surrounding conditions and operat-
ing the steering wheel to correct the path of the vehicle. Also, the driver must take adequate breaks when fatigued, such as
from driving for a long period of time. Failure to perform appropriate driving operations and pay careful attention may
lead to an accident, resulting in death or serious injury.
■To avoid operating LKA system by mistake
When not using the LKA system, use the LKA switch to turn the system off.
■Situations unsuitable for LKA system
Do not use the LKA system in the follow- ing situations.The system may not operate properly
and lead to an accident, resulting in death or serious injury.
●A spare tire, tire chains, etc. are equipped.
●When the tires have been excessively
worn, or when the tire inflation pres- sure is low.
●Tires which differ by structure, manu-facturer, brand or tread pattern are
used.
●Objects or patterns that could be mis- taken for white (yellow) lines are pres-ent on the side of the road (guardrails,
curbs, reflective poles, etc.).
●Vehicle is driven on a snow-covered road.
●White (yellow) lines are difficult to see due to rain, snow, fog, dust, etc.
●Asphalt repair marks, white (yellow) line marks, etc. are present due to road repair.
●Vehicle is driven in a temporary lane or
restricted lane due to construction work.
●Vehicle is driven on a road surface which is slippery due to rainy weather,
fallen snow, freezing, etc.
●Vehicle is driven in traffic lanes other than on highways and freeways.
●Vehicle is driven in a construction zone.
■Preventing LKA system malfunctions
and operations performed by mistake
●Do not modify the headlights or place
stickers, etc. on the surface of the lights.

224
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
●The vehicle is driven on a surface that is bright due to reflected light, etc.
●The vehicle is driven in an area where the brightness changes suddenly, such as at the entrances and exits of tunnels, etc.
●Light from the headlights of an oncoming vehicle, the sun, etc. enters the camera.
●The vehicle is driven where the road diverges, merges, etc.
●The vehicle is driven on a slope.
●The vehicle is driven on a road which tilts left or right, or a winding road.
●The vehicle is driven on an unpaved or rough road.
●The vehicle is driven around a sharp curve.
●The traffic lane is excessively narrow or wide.
●The vehicle is extremely tilted due to car-rying heavy luggage or having improper tire pressure.
●The distance to the preceding vehicle is extremely short.
●The vehicle is moving up and down a
large amount due to road conditions during driving (poor roads or road seams).
●The headlight lenses are dirty and emit a faint amount of light at night, or the beam
axis has deviated.
●The vehicle is struck by a crosswind.
●The vehicle has just changed lanes or crossed an intersection.
●Snow tires, etc. are equipped.
■Warning message
If the following warning message is dis- played on the multi-information display and the LKA indicator illuminates in orange, fol-
low the appropriate troubleshooting proce- dure.
Warning mes-
sageDetails/Actions
“Lane Keep-
ing Assist
Malfunction
Visit Your
Dealer”
The system may not be
operating properly.
 Have the vehicle
inspected any authorized
Lexus retailer or Lexus
authorized repairer, or
any reliable repairer.
“Front Cam-
era Vision
Blocked
Clean and
Demist Wind-
shield”
Dirt, rain, condensation,
ice, snow, etc. are present
on the windshield in front
of the camera sensor.
 Turn the LKA system
off, remove any dirt, rain,
condensation, ice, snow,
etc. from the windshield,
and then turn the LKA sys-
tem back on.
“Front Cam-
era Unavail-
able”
The operation conditions
of the camera sensor
(temperature, etc.) are
not met.
 When the operation
conditions of the camera
sensor (temperature, etc.)
are met, the LKA system
will become available.
Turn the LKA system off,
wait for a little while, and
then turn the LKA system
back on.

355
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
Rear fog light
■Bulbs that need to be replaced by
any authorized Lexus retailer or
Lexus authorized repairer, or any
reliable repairer
 Headlights
 Front position lights and daytime
running lights
 Front turn signal lights
 Cornering lights
 Side turn signal lights
 Tail lights
 Stop lights
 Rear turn signal lights
 Back-up lights
 High mounted stoplight
 License plate lights
■LED lights
The lights other than the rear fog light each
consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to any authorized Lexus retailer or Lexus autho-
rized repairer, or any reliable repairer to have the light replaced.
■Condensation build-up on the inside of
the lens
Temporary condensation build-up on the
inside of the headlight lens does not indi- cate a malfunction. Contact any authorized Lexus retailer or Lexus authorized repairer,
or any reliable repairer for more informa- tion in the following situations:
●Large drops of water have built up on the inside of the lens.
●Water has built up inside the headlight.
■When replacing light bulbs
 P.354
Light bulbs
You may replace the following bulbs
by yourself. Before replacing,
check the wattage of the light bulb
to be replaced. As there is a danger
that components may be damaged,
we recommend that replacement is
carried out by any authorized Lexus
retailer or Lexus authorized
repairer, or any reliable repairer.
Bulb location
A