lock lexus LC500 2018 User Guide

32
-$@-$I@0.@0.&@ &&

1-1. For safe use
Do not twist the seat belt.
Not twisted
Twisted
■Child seat belt usage
The seat belts of your vehicle were princi- pally designed for persons of adult size.
●Use a child restraint system appropriate for the child, until the child becomes large
enough to properly wear the vehicle’s seat belt. ( P.48)
●When the child becomes large enough to properly wear the vehicle’s seat belt, fol-
low the instructions regarding seat belt usage.
■Seat belt regulations
If seat belt regulations exist in the country where you reside, please contact any authorized Lexus retailer or Lexus autho-
rized repairer, or any reliable repairer for seat belt replacement or installation.
1 To fasten the seat belt, push the
plate into the buckle until a click
sound is heard.
2 To release the seat belt, press the
release button .
■Emergency locking retractor (ELR)
The retractor will lock the belt during a sud- den stop or on impact. It may also lock if you
lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.
The front seats are equipped with
guides to allow the seat belts to be
extended easily. When it is difficult to
extend the seat belt, pass the seat belt
through the guide.
When getting into or out of a rear seat,
release the seat belt from the guide.
A
B
Fastening and releasing the seat
belt
Seat belt guide
A

44
-$@-$I@0.@0.&@ &&

1-1. For safe use
●A frontal impact applied to the front bumper while driving at speeds outside of the operational speed range
●A side impact or rear impact
●A vehicle rollover (In some accident situ-ations, the Pop Up Hood may operate.)
WARNING
■When the Pop Up Hood is operated
●Do not pull the hood lock release lever.
Doing so after the Pop Up Hood has operated will further raise the hood and may cause an injury. Do not drive
with the hood raised, as doing so may block the driver’s vision, possibly caus-ing an accident.
●Do not forcibly push down the hood.
As the popped up hood cannot be lowered by hand, doing so may deform the hood or cause an injury.
●If the Pop Up Hood has operated, have
it replaced by any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer. If the Pop Up
Hood has operated, stop the vehicle in a safe place and contact authorized Lexus retailer or Lexus authorized
repairer, or any reliable repairer.
●Do not touch the lifters immediately after the Pop Up Hood has operated, as the lifters may be hot and burn you.
NOTICE
■Pop Up Hood precautions
●Make sure to close the hood before driving, as the system may not operate
properly if the hood is not fully closed.
●Make sure that all 4 tires are of the specified size and inflated to the speci-fied tire pressure. If tires of a different
size are used, the system may not operate properly.
●If something has hit the area around the front bumper, the sensors may be
damaged even if the Pop Up Hood has not operated. Have the vehicle inspected by any authorized Lexus
retailer or Lexus authorized repairer, or any reliable repairer.
●Do not remove or repair the parts or wiring of the Pop Up Hood, as doing
so may cause accidental operation or prevent the system from operating properly. If repair or replacement is
necessary, contact any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer.
●Do not remove such components as
the front bumper, hood or suspension, or replace them with non-genuine parts, as doing so may prevent the sys-
tem from operating properly.
●Do not install anything to the front bumper or hood, as doing so may pre-vent the sensors from detecting an
impact correctly and prevent the sys- tem from operating properly.
●Do not close the hood with force or
apply load to the lifters, as doing so may damage the lifters and prevent the system from operating properly.
●Do not modify the suspension, as
changes made to the vehicle height may prevent the system from operat-ing properly.

47
1
-$@-$I@0.@0.&@ &&

1-2. Child safety
For safety and security
WARNING
■When installing a child restraint sys- tem
For safety reasons, always install a child restraint system in a rear seat. In the event that the rear seat cannot be used,
the front seat can be used as long as the airbag manual on-off system is set to “OFF”.
If the airbag manual on-off system is left on, the strong impact of the airbag deployment (inflation) may cause serious
injury or even death.
■When a child restraint system is not installed on the front passenger seat
Ensure that the airbag manual on-off sys- tem is set to “ON”.If it is left off, the airbag may not deploy in
the event of an accident, which may result in serious injury or even death.
Riding with children
Observe the following precautions
when children are in the vehicle.
Use a child restraint system appro-
priate for the child, until the child
becomes large enough to properly
wear the vehicle’s seat belt.
 It is recommended that children
sit in the rear seats to avoid acci-
dental contact with the shift lever,
wiper switch, etc.
 Use the window lock switch to
avoid children operating the
power window accidentally.
( P.152)
 Do not let small children operate
equipment which may catch or
pinch body parts, such as the
power window, hood, trunk, seats
etc.
WARNING
■When children are in the vehicle
Never leave children unattended in the vehicle, and never allow children to have or use the key.
Children may be able to start the vehicle or shift the vehicle into neutral. There is
also a danger that children may injure themselves by playing with the windows or other features of the vehicle. In addi-
tion, heat build-up or extremely cold temperatures inside the vehicle can be fatal to children.

56
-$@-$I@0.@0.&@ &&

1-2. Child safety
When installing a forward-facing
child seat, if there is a gap between
the child seat and the seatback,
adjust the seatback angle until good
contact is achieved.
 If the seat belt shoulder anchor is
ahead of the child seat belt guide,
move the seat cushion forward.
 When installing a junior seat, if the
child in your child restraint system is
in a very upright position, adjust the
seatback angle to the most comfort-
able position. And if the seat belt
shoulder anchor is ahead of the
child seat belt guide, move the seat
cushion forward.
■Installing child restraint system
using a seat belt
Install the child restraint system in
accordance to the operation manual
enclosed with the child restraint sys-
tem.
1 If installing the child restraint sys-
tem to the front passenger seat is
unavoidable, refer to P.51 for front
passenger seat adjustment.
2 If the head restraint interferes with
the child restraint system installa-
tion and the head restraint can be
removed, remove the head
restraint. Otherwise, put the head
restraint in the upper most position.
( P.143)
3 Run the seat belt through the child
restraint system and insert the plate
into the buckle. Make sure that the
belt is not twisted. Securely fix the
seat belt to the child restraint sys-
tem in accordance to the directions
enclosed with the child restraint
system.
4 If your child restraint system is not
equipped with a lock-off (a seat belt

57
1
-$@-$I@0.@0.&@ &&

1-2. Child safety
For safety and security
locking feature), secure the child
restraint system using a locking clip.
5 After installing the child restraint
system, rock it back and forth to
ensure that it is installed securely.
( P.57)
■Removing a child restraint system
installed with a seat belt
Press the buckle release button and
fully retract the seat belt.
When releasing the buckle, the child
restraint system may spring up due to the
rebound of the seat cushion. Release the
buckle while holding down the child
restraint system.
Since the seat belt automatically reels itself,
slowly return it to the stowing position.
■When installing a child restraint system
You may need a locking clip to install the child restraint system. Follow the instruc-tions provided by the manufacturer of the
system. If your child restraint system does not provide a locking clip, you can purchase the following item from any authorized
Lexus retailer or Lexus authorized repairer, or any reliable repairer: Locking clip for child restraint system (Part
No. 73119-22010)
■ISOFIX rigid anchors (ISOFIX
child restraint system)
Lower anchors are provided for the
each rear seat. (Buttons displaying the
location of the anchors are attached to
the seats.)
WARNING
■When installing a child restraint sys- tem
Observe the following precautions. Failure to do so may result in death or serious injury.
●Do not allow children to play with the
seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious inju-
ries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to
cut the belt.
●Ensure that the belt and plate are securely locked and the seat belt is not twisted.
●Shake the child restraint system left
and right, and forward and backward to ensure that it has been securely installed.
●After securing a child restraint system,
never adjust the seat.
●When a junior seat is installed, always ensure that the shoulder belt is posi-tioned across the center of the child’s
shoulder. The belt should be kept away from the child’s neck, but not so that it could fall off the child’s shoulder.
●Follow all installation instructions pro-
vided by the child restraint system manufacturer.
Child restraint system fixed with
an ISOFIX rigid anchor

68
-$@-$I@0.@0.&@ &&

1-3. Hybrid system
There are air intake vents under the
rear seats for the purpose of cooling
the hybrid battery (traction battery). If
the vents become blocked, the hybrid
battery input and output may be
restricted, leading to a reduction in
hybrid battery (traction battery) out-
put.
When a certain level of impact is
detected by the impact sensor, the
emergency shut off system blocks the
high voltage current and stops the fuel
pump to minimize the risk of electrocu-
tion and fuel leakage. If the emergency
shut off system activates, your vehicle
will not restart. To restart the hybrid
system, contact any authorized Lexus
retailer or Lexus authorized repairer,
or any reliable repairer.
A message is automatically displayed
when a malfunction occurs in the
hybrid system or an improper opera-
tion is attempted.
If a warning message is shown on the
multi-information display, read the
NOTICE
■Hybrid battery (traction battery)
Do not carry large amounts of water
such as water cooler bottles in the vehi- cle. If water spills onto the hybrid battery (traction battery), the battery may be
damaged. Have the vehicle inspected by any authorized Lexu s retailer or Lexus authorized repairer, or any reliable
repairer.
Hybrid battery (traction bat-
tery) air intake vents
NOTICE
■Hybrid battery (traction battery) air intake vents
●Make sure not to block the air intake vents with anything, such as a seat cover, plastic cover, or luggage. If the
vents become blocked, the hybrid bat- tery (traction battery) input and output may be restricted, leading to a reduc-
tion in hybrid battery (traction battery) output and a malfunction.
●When dust etc. has accumulated in the air intake vents, periodically clean
them with a vacuum cleaner to prevent the vents from clogging.
●Filters are installed to the air intake vents. When the filters remain notice-
ably dirty even after cleaning the air intake vents, filter cleaning or replace-ment is recommended. When clean-
ing or replacing the filters, contact any authorized Lexus retailer or Lexus authorized repairer, or any reliable
repairer. Refer to P.309 for details on how to clean the filters.
●Do not get water or foreign materials
in the air intake vents as this may cause a short circuit and damage the hybrid battery (traction battery).
Emergency shut off system
Hybrid warning message

75
1
-$@-$I@0.@0.&@ &&

1-4. Theft deterrent system
For safety and security
■Setting
Turn the engine switch
off, have all the passengers exit the
vehicle and ensure that both side doors
are closed.
Press twice within 5 seconds.
■Canceling
Using the entry function: Push the
edge of the door handle to unlock the
doors.
Using the wireless remote control:
Press .
NOTICE
■To ensure the system operates cor- rectly
Do not modify or remove the system. If modified or removed, the proper opera-tion of the system cannot be guaranteed.
Double locking system
Unauthorized access to the vehicle
is prevented by disabling the door
unlocking function from both the
interior and exterior of the vehicle.
Vehicles employing this system
have labels on the side windows.
Setting/canceling the double
locking system

76
-$@-$I@0.@0.&@ &&

1-4. Theft deterrent system
*:If equipped
■Items to check before locking the
vehicle
To prevent unexpected triggering of
the alarm and vehicle theft, make sure
of the following:
 Nobody is in the vehicle.
 The windows are closed before the
alarm is set.
 No valuables or other personal
items are left in the vehicle.
WARNING
■Double locking system precaution
Never activate the do uble locking sys-
tem when there are people in the vehicle because both side doors cannot be opened from inside the vehicle.
Alarm*
The alarm uses light and sound to
give an alert when an intrusion is
detected.
The alarm is triggered in the follow-
ing situations when the alarm is set:
 A locked door or trunk is
unlocked or opened in any way
other than using the entry func-
tion or wireless remote control.
(The door will lock again auto-
matically.)
 The hood is opened.
 The intrusion sensor detects
something moving inside the
vehicle. (Example: an intruder
breaks a window and gets into the
vehicle.)
 The tilt sensor detects a change of
vehicle inclination.
Setting/canceling/stopping the
alarm system

77
1
-$@-$I@0.@0.&@ &&

1-4. Theft deterrent system
For safety and security
■Setting
Close the doors, trunk and hood, and
lock both side doors using the entry
function or wireless remote control.
The system will be set automatically
after 30 seconds.
The indicator light changes from being on
to flashing when the system is set.
■Canceling or stopping
Do one of the following to deactivate
or stop the alarm:
 Unlock the doors or open the trunk
using the entry function or wireless
remote control.
 Start the engine .
(The alarm will be deactivated or
stopped after a few seconds.)
■System maintenance
The vehicle has a maintenance-free type alarm system.
■Triggering of the alarm
The alarm may be triggered in the following situations:(Stopping the alarm deactivates the alarm
system.)
●The doors are unlocked using the
mechanical key.
●A person inside the vehicle opens a door, the trunk or hood, or unlocks the vehicle using a door lock switch.
●The 12-volt battery is recharged or replaced when the vehicle is locked.
( P.398)
■Alarm-operated door lock
In the following cases, depending on the sit-
uation, the door may automatically lock to prevent improper entry into the vehicle:
●When a person remain ing in the vehicle unlocks the door and the alarm is acti-vated.
●While the alarm is activated, a person remaining in the vehicle unlocks the door.
●When recharging or replacing the 12-volt battery

78
-$@-$I@0.@0.&@ &&

1-4. Theft deterrent system
■The intrusion sensor and tilt sensor
detection
 The intrusion sensor detects intrud-
ers or movement in the vehicle.
 The tilt sensor detects changes in
vehicle inclination, such as when the
vehicle is towed away.
This system is designed to deter and
prevent vehicle theft but does not
guarantee absolute security against all
intrusions.
■Setting the intrusion sensor and tilt
sensor
The intrusion sensor and tilt sensor will
be set automatically when the alarm is
set. ( P.77)
■Canceling the intrusion sensor and
tilt sensor
If you are leaving pets or other moving
things inside the vehicle, make sure to
disable the intrusion sensor and tilt
sensor before setting the alarm, as they
will respond to movement inside the
vehicle.
1 Turn the engine switch switch> off.
2 Press the intrusion sensor and tilt
sensor cancel switch.
Press the switch again to re-enable the intrusion sensor and tilt sensor.
Each time the intrusion sensor and tilt sen- sor are canceled/set, a message will be shown on the multi-information display in
the instrument cluster.
■Canceling and automatic re-enabling of
the intrusion sensor and tilt sensor
●The alarm will still be set even when the
intrusion sensor and tilt sensor are can- celed.
●After the intrusion sensor and tilt sensor are canceled, pressing the engine switch or unlocking the doors
using the entry function or wireless remote control will re-enable the intru-sion sensor and tilt sensor.
●The intrusion sensor and tilt sensor will automatically be re-enabled when the
alarm system is deactivated.
■Intrusion sensor detection consider- ations
The sensor may trigger the alarm in the fol- lowing situations:
●People or pets are in the vehicle.
●A window is open.
In this case, the sensor may detect the fol-
NOTICE
■To ensure the system operates cor- rectly
Do not modify or remove the system. If modified or removed, the proper opera-tion of the system cannot be guaranteed.
Intrusion sensor and tilt sensor