oil lexus LFA 2012 Technical Information / LEXUS 2012 LFA (OM77006U) User Guide

132
2-2. Instrument cluster
“Status” (vehicle status)“Trip Info”, “Oil Level”, “Oil Maintenance” and “Tire Pressure” information
can be checked. Select “Status” and press right on
the control pad.
Select the desired menu item and
press right on the control pad.
“Trip Info” (P. 133)
“Oil Level” ( P. 135)
“Oil Maintenance” ( P. 1 3 8 )
“Tire Pressure” ( P. 140)
STEP1
STEP2

135
2-2. Instrument cluster
2
When driving
■“Oil Level” (engine oil level)
The amount of oil remaining in the ta nk can be calculated and is shown
on a scale of one to ten . If the engine oil level cannot be measured, the
reason will be shown on the screen.
Conditions for measurement
● The engine oil temperature is between 203 F and 230F (95C and
110 C).
● The engine is idling.
● The vehicle is stopped on level ground.
Select “Oil Level” and press right
on the control pad.
The amount of engine oil remain-
ing is measured automatically.
The amount of time needed to
complete the measurement is
counted down on the screen.
STEP1
STEP2

136
2-2. Instrument cluster
Measurement resultOnce measurement is complete,
the result will be displayed.
The oil amount between the maxi-
mum and minimum markings is
approximately 2.1 qt. (2.0 L, 1.8
Imp. qt.).
As the engine oil level in the oil
tank varies depending on the driv-
ing condition of the vehicle imme-
diately before measurement, the
results may vary even if the overall
oil amount is constant.
Perform the following actions as necessary according to the measure-
ment results:
● If the oil level is low, add engine oil as needed. ( P. 257)
Even if the measurement result shows th at the engine oil is below the maxi-
mum level, be careful not to add more oil than necessary. If unsure of how
much oil to add, contact your Lexus dealer.
● If “Engine oil level low Check oil le vel” is displayed on the meter, avoid
high load driving and add oil immediately.
Do not let the oil level reach or fall below the minimum marking, as doing so
may cause engine damage.
MAX
MIN

137
2-2. Instrument cluster
2
When driving
“Cannot measure” displayIf measurement cannot be per-
formed, the item with “No” dis-
played may be the cause. Check
the following items and then
attempt to perform the measure-
ment again:
If the measuring function does not work even after all the above condi-
tions have been met, have the vehicle inspected by your Lexus dealer.
ItemDetailsCorrection procedure
Engine Warm The engine oil has not
warmed sufficiently. Measure when the engine
oil temperature is between
203
F and 230 F (95 C
and 110 C).
Idling The engine speed is too low
or too high. Measure when the engine
speed is between 900 rpm
and 1100 rpm.
Stationary The vehicle is not com-
pletely stationary. Measure when the vehicle
is completely stopped with
Neutral selected and the
parking brake set.
Vehicle Level The vehicle is parked on an
incline. Measure when the vehicle
is on level ground with an
incline of 4 degrees or less.

138
2-2. Instrument cluster
■“Oil Maintenance” (engine oil maintenance)
This system calculates engine oil replacement timing and reminds the
driver when it is time to replace th e oil. Resetting operation should be
performed at your Lexus dealer when you have them change the
engine oil. (This procedure cannot be performed while the vehicle is in
motion.)
Select “Oil Maintenance” and
press right on the control pad.
Press and hold right on the control
pad for 5 seconds.
STEP1
STEP2

139
2-2. Instrument cluster
2
When driving
“Complete” will be displayed when
the reset procedure has been
completed.
The system will start measuring the
distance to the next engine oil
replacement timing.
STEP3

154
2-2. Instrument cluster
■“Units”
The units of measurement used fo r the speedometer, odometer, and
trip information can be changed.
Each time right on the control pad
is pressed, the distance (miles,
km), the speed (MPH, km/h) and
the fuel consumption (MPG, km/l,
L/100km) measurement units will
be changed.
■ “Temp” (temperature)
The units of measurement used fo r the outside temperature, engine
coolant temperature, engine oil temperature and air conditioning tem-
perature displays can be changed.
Each time right on the control pad
is pressed, the temperature display
unit will be changed (Fahrenheit,
Celsius).

156
2-2. Instrument cluster
■Meter operation restrictions while vehicle is in motion
While the vehicle is in motion, some menu items cannot be changed using the con-
trol pad. Restricted items are displayed in gray or without an arrow. These items can
be operated once the vehicle is stopped.
■“Rev Ind” (rev indicator)
●Even if the green or amber indicator is set to 9000 rpm, the over-rev warning
will be displayed.
●If the green and amber indicators are both set to the same engine speed, the
indicator will be shown in amber.
■Measuring the engine oil level
●The dry sump lubrication system circulates the engine oil between the engine
and oil tank according to driving conditions. Accordingly, the engine oil level in
the oil tank may vary even if the overall amount is constant, affecting the mea-
surement results.
●It takes some time for the engine oil level to stabilize after the engine is started.
To obtain a more stable result, drive the vehicle for a while and then perform the
measurement without stopping the engine.
●If an attempt to measure the oil level is made immediately after the previous oil
level measurement process was completed, the previous measurement may be
displayed.
●If the measurement result flashes, the measuring function is malfunctioning.
Have the vehicle inspected by your Lexus dealer.
■Engine oil maintenance
“Oil maintenance required” will be displayed once the vehicle has been driven for
more than 6214 miles (10000 km) since the last reset. (
P. 3 2 7 )
The engine oil may need to be replaced earlier depending on driving conditions.
●Over-rev warning (regular setting)
If the engine speed enters the red zone, the
over-rev warning will be shown in red
regardless of the set speed.

181
2-5. Driving information
2
When driving
■Tire grip at low temperatures
The tires fitted to the LFA are designed for dry road conditions. As such, tire grip on
cold, snowy and/or icy roads will be reduced compared to standard tires.
Be sure to use snow tires on snowy and/or icy roads and drive carefully at a speed
appropriate for road and weather conditions.
■Engine starting restrictions
In order to protect the engine, the engine may not start when the engine coolant
temperature or engine oil temperature is below -13 F (-25C). In that case, a
buzzer will sound and “Temp low Engine cannot be started” will be shown on the
meter. ( P. 3 2 7 )
CAUTION
■Driving with snow tires
Observe the following precautions to reduce the risk of accidents.
Failing to do so may result in a loss of vehicle control and cause death or serious
injury.
●Use tires of the specified size.
●Maintain the recommended level of air pressure.
●Do not drive in excess of 75 mph (120 km/h), regardless of the type of snow tires
being used.
●Use snow tires on all, not just some wheels.
NOTICE
■Driving with tire chains
Do not fit tire chains. Tire chains may da mage the vehicle body and suspension, and
adversely affect driving performance.
■Repairing or replacing snow tires
Request repairs or replacement of snow ti res from Lexus dealers or legitimate tire
retailers.
This is because the removal and attachment of snow tires affects the operation of
the tire pressure warning valves and transmitters.

231
4-1. Maintenance and care
4
Maintenance and care
NOTICE
■Application of coatings to the vehicle body
Do not apply any kind of coating to the vehicle body as doing so may damage the
paint or reduce its durability.
■To prevent paint deterioration and corrosion on the body and components (alu-
minum wheels etc.)
Observe the following precautions:
●Wash the vehicle immediately in the following cases:
• After driving near the sea coast
• After driving on salted roads
• If coal tar or tree sap is present on the paint surface
• If dead insects, insect droppings or bird droppings are present on the paint
surface
• After driving in an area contaminated with soot, oily smoke, mine dust, iron
powder or chemical substances
• If the vehicle becomes heavily soiled with dust or mud
• If liquids such as benzene and gasoline are spilled on the paint surface
●If the paint is chipped or scratched, have it repaired immediately.
●To prevent the wheels from corroding, remove any dirt and store in a place with
low humidity when storing the wheels.
For the Matte Black, pay attent ion to the following as well:
●If anything is spilled on a painted surface, wipe it off as soon as possible.
If spilled washer fluid or alkaline fluids are left as is, the paint in the affected area
may deteriorate, causing blemishing.
●Do not wax or apply coating to the vehicle.
Doing so may cause a change in the body surface's texture or irregularities in the
paint.