key lexus LS400 1994 Engine / 1994 LS400: STARTING AND DRIVING

STARTING AND DRIVING
120
BEFORE STARTING THE ENGINE
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, headrest height and
steering wheel angle.
3. Adjust inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts.
Remember to check that the service reminder, indicators
function when turning the key to “ON”, and check the fuel
gauge to see that you have sufficient fuel.
IGNITION SWITCH WITH STEERING
LOCK
“START” − Starter motor on. The key will return to the
“ON” position when released.For starting tips, see page 121.
“ON” − Engine on and all accessories on.
This is the normal driving position.
NOTICE:
Do not leave the key in the “ON” position if the engine is
not running. The battery will discharge and the
electronic ignition system / distributor ignition system
could be damaged.
“ACC” − Accessories such as the radio operate, but the
engine is off.
If you leave the key in the “ACC” or “LOCK” position and open
the driver’s door, a buzzer will remind you to remove the key.
“LOCK” − Engine is off and the steering wheel is locked.
The key can be removed only at this position.
To turn the key from “ACC” to the “LOCK” position, you must
put the transmission selector lever in the “P” position.

STARTING AND DRIVING
121 When starting the engine, the key may seem stuck at the
“LOCK” position. To free it, first be sure the key is pushed all
the way in, and then rock the steering wheel slightly while
turning the key gently.
If, in an emergency, you must turn the engine off while the
vehicle is in motion, turn the key only to “ACC”.
PARKING BRAKE
Release
Set
To set: Fully depress the parking brake pedal.
To release: Pull the parking brake release lever.
Before leaving your vehicle, firmly apply the parking brake.
CAUTION:
Before driving, make sure the parking brake is fully
released and that the parking brake reminder light is off.
HOW TO START THE ENGINE
Before cranking
1. Apply the parking brake firmly.
2. Turn off unnecessary lights and accessories.
3. Put the selector lever in “P”. If you need to restart the engine
while the vehicle is moving, put the selector lever in “N”. A
starter safety device will prevent the starter from operating if
the selector lever is in any drive position.
4. Depress the brake pedal and hold it to the floor until you are
ready to drive off.
Starting the engine
Before starting the engine, be sure to follow the instructions in
“Before cranking”.
Normal starting procedure
The multiport fuel injection system / sequential multiport fuel
injection system in your engine automatically controls the
proper air-fuel mixture for starting. You can start a cold or hot
engine as follows:
1. With your foot off the accelerator pedal, crank the engine by
turning the key to “START”. Release it when the engine starts.
2. After the engine runs for about 10 seconds, you are ready
to drive.
If the weather is below freezing, let the engine warm up for a
few minutes before driving. Do not leave the vehicle while the
engine is warming up.

STARTING AND DRIVING
With the brake pedal depressed, shift
while pressing the lock release button in
(The ignition switch must be in the “ON” position.)
Shift while pressing the lock
release button in
Shift without pressing
the button
Lock release button
To prevent misshifting
Parking, engine starting
and key removal position
Reverse position
Neutral position
Normal driving position
Position for engine braking
Position for stronger engine braking
than that in “2” position
Overdrive switch
For selecting either a three-speed
or four-speed transmission
ON position
(Shifting into overdrive possible)
OFF position
(Shifting into overdrive not possible)
Shift position indicator
Shows the selector lever position
Shift position is also displayed
on the instrument cluster
Driving pattern selector switch
For selecting a driving pattern suitable
to existing driving conditions
NORMAL position
for general driving
conditions
POWER position
for powerful acceleration
123
AUTOMATIC TRANSMISSION

STARTING AND DRIVING
124Your automatic transmission has a shift lock system to
minimize the possibility of incorrect operation. This means you
can only shift out of “P” position when the brake pedal is
depressed (with the ignition switch in “ON” position and the
lock release button pressed in).
Correct use of the automatic transmission is explained in the
following parts.
(a) Normal driving
(b) Using engine braking
(c) Using the “2” and “L” positions
(d) Backing up
(e) Parking
(f) Good driving practice
(g) If you cannot shift the selector lever out of “P” position
(h) If the “O / D OFF” indicator light flashes
(a) Normal driving
“P” (Park)
position
“N” (Neutral)
position
1. Start the engine as instructed in “How to start the
engine” on page 121.
The transmission must be in “P” or “N”. The engine will not start
in “R”, “2”, “L” or “D” position even if the key is turned to
“START”.
Driving pattern
selector switchIndicator light
Power position
Normal position
2. Set the driving pattern selector switch to the NORMAL
position.
Your transmission has a driving pattern selector switch which
allows you to select either “NORM” or “PWR” to suit your
driving condition. For ordinary driving, Lexus recommends that
you use the NORMAL position to improve fuel economy.
3. For more powerful acceleration and sporty driving, use
the POWER position.
In the POWER position, the “ECT PWR” light in the instrument
cluster is on and the transmission is shifted up at higher vehicle
speeds and shifted down more responsively than in the
NORMAL position.

STARTING AND DRIVING
129
Turning on the system
To operate the cruise control, push the main switch. This turns
the system on. The indicator light in the instrument cluster
shows that you can now set your desired cruising speed.
Another push on the switch will turn the system completely off.
When the ignition key is turned off, the main switch is also
automatically turned off. To use the cruise control again, push
the main switch again to turn it on.
CAUTION:
To avoid accidental cruise control engagement, keep the
main switch off when not using the cruise control.
Setting at a desired speed
Bring the vehicle to the desired speed, press the control lever
downward in the “SET / COAST” direction and release it. This
sets the vehicle at that speed. Now you may take your foot off
the accelerator pedal. If you need acceleration − for example,
when passing − depress the accelerator pedal enough for the
vehicle to exceed the set speed. When you release the
accelerator, the vehicle will return to the speed set prior to the
acceleration.
Cancelling the preset speed
You can cancel the preset speed by either of the following:
a. Pulling the control lever in the “CANCEL” direction.
b. Depressing the brake pedal.

STARTING AND DRIVING
132
The indicator light shows the selector switch is in
“SPORT” position. When the indicator light is not on, this
means the selector switch is in “NORMAL” position.
When you turn the ignition key to the “ON” position, the
indicator lights will come on for two seconds.
HEIGHT CONTROL SYSTEM
(U. S. A. ONLY)
The height control system adjusts the vehicle height. This
adjustment is automatically made in response to the
driving conditions to provide good riding comfort and
stability in all driving conditions.
(a) Vehicle height adjustment
Push the selector switch to select one of the following modes:
“NORMAL” mode − For driving on roads with a normal
surface.
“HIGH” mode − For driving on rough roads which are
unsurfaced or continually bumpy.
To change the mode, push the selector switch.
“NORMAL” mode
The vehicle height remains at normal height at all driving
speeds.

STARTING AND DRIVING
133 “HIGH” mode
The vehicle height switches between the following two vehicle
heights according to the driving conditions:
Vehicle height
Driving condition
NormalHigh-speed driving
HighLow and medium speed driving
The indicator light shows the vehicle height is high.
When you turn the ignition key to the “ON” position, the
indicator light will come on for 2 seconds.
(b) Height control ON / OFF switch
OnOff
This switch is located inside the tool storage section on the left
side of the trunk compartment. Sliding the switch to the OFF
position will turn off the height control system. When the switch
is turned off, the “HI” display plinks.
NOTICE:
Before jacking up, towing or hoisting the vehicle, always
turn the height control ON / OFF switch to OFF. If this is
not done, the vehicle height automatic adjustment
function will operate, causing imbalance of the vehicle
and contact of the bumper, etc. with the road surface.
(c) Malfunction warning
If the “HI” display blinks when the height control ON / OFF
switch is turned on, there is a malfunction in the Lexus ride
control system or height control system.

STARTING AND DRIVING
136Always maintain a safe distance from the vehicle in front of
you. Compared with vehicles not fitted with an anti-lock brake
system, your vehicle requires a longer stopping distance in the
following cases:

Driving on rough, gravel or snow-coverd roads.

Driving with tire chains installed.

Driving on roads where the road surface is pitted or has
other differences in surface height.
Avoid high speeds on wet roads. The anti-lock brake system
cannot eliminate the risk of aquaplaning.
Anti-lock brake system warning light
This light comes on when the ignition key is turned to the
“ON” position. After a few seconds, the light will go off.If either of the following conditions occurs, this indicates a
malfunction somewhere in the parts monitored by the warning
light system. Contact Your Lexus dealer as soon as possible
to service the vehicle.

The light does not come on as described above, or remains
on.

The light comes on while driving.
Even if the anti-lock brake system should fail, the brake system
will still operate conventionally. Have your vehicle checked by
your Lexus dealer as soon as possible.
Drum-in-disc type parking brake system
Your vehicle has a drum-in-disc type parking brake system.
This type of brake system needs bedding-down of the brake
shoes periodically or whenever the parking brake shoes
and / or drums are replaced.
Have your Lexus dealer perform the bedding-down.