lock lexus LS400 1994 Engine / 1994 LS400: STARTING AND DRIVING

SECTION 3 – 1
11 7
STARTING AND DRIVING
Starting and driving
Three-way catalytic converter11 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine exhaust caution
11 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before starting the engine120 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition switch with steering lock120 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking brake121 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to start the engine121 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic transmission123 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cruise control128 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lexus ride control system131 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Height control system132 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Traction control system134 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake system135 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Types of tires137 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

STARTING AND DRIVING
120
BEFORE STARTING THE ENGINE
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, headrest height and
steering wheel angle.
3. Adjust inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts.
Remember to check that the service reminder, indicators
function when turning the key to “ON”, and check the fuel
gauge to see that you have sufficient fuel.
IGNITION SWITCH WITH STEERING
LOCK
“START” − Starter motor on. The key will return to the
“ON” position when released.For starting tips, see page 121.
“ON” − Engine on and all accessories on.
This is the normal driving position.
NOTICE:
Do not leave the key in the “ON” position if the engine is
not running. The battery will discharge and the
electronic ignition system / distributor ignition system
could be damaged.
“ACC” − Accessories such as the radio operate, but the
engine is off.
If you leave the key in the “ACC” or “LOCK” position and open
the driver’s door, a buzzer will remind you to remove the key.
“LOCK” − Engine is off and the steering wheel is locked.
The key can be removed only at this position.
To turn the key from “ACC” to the “LOCK” position, you must
put the transmission selector lever in the “P” position.

STARTING AND DRIVING
121 When starting the engine, the key may seem stuck at the
“LOCK” position. To free it, first be sure the key is pushed all
the way in, and then rock the steering wheel slightly while
turning the key gently.
If, in an emergency, you must turn the engine off while the
vehicle is in motion, turn the key only to “ACC”.
PARKING BRAKE
Release
Set
To set: Fully depress the parking brake pedal.
To release: Pull the parking brake release lever.
Before leaving your vehicle, firmly apply the parking brake.
CAUTION:
Before driving, make sure the parking brake is fully
released and that the parking brake reminder light is off.
HOW TO START THE ENGINE
Before cranking
1. Apply the parking brake firmly.
2. Turn off unnecessary lights and accessories.
3. Put the selector lever in “P”. If you need to restart the engine
while the vehicle is moving, put the selector lever in “N”. A
starter safety device will prevent the starter from operating if
the selector lever is in any drive position.
4. Depress the brake pedal and hold it to the floor until you are
ready to drive off.
Starting the engine
Before starting the engine, be sure to follow the instructions in
“Before cranking”.
Normal starting procedure
The multiport fuel injection system / sequential multiport fuel
injection system in your engine automatically controls the
proper air-fuel mixture for starting. You can start a cold or hot
engine as follows:
1. With your foot off the accelerator pedal, crank the engine by
turning the key to “START”. Release it when the engine starts.
2. After the engine runs for about 10 seconds, you are ready
to drive.
If the weather is below freezing, let the engine warm up for a
few minutes before driving. Do not leave the vehicle while the
engine is warming up.

STARTING AND DRIVING
With the brake pedal depressed, shift
while pressing the lock release button in
(The ignition switch must be in the “ON” position.)
Shift while pressing the lock
release button in
Shift without pressing
the button
Lock release button
To prevent misshifting
Parking, engine starting
and key removal position
Reverse position
Neutral position
Normal driving position
Position for engine braking
Position for stronger engine braking
than that in “2” position
Overdrive switch
For selecting either a three-speed
or four-speed transmission
ON position
(Shifting into overdrive possible)
OFF position
(Shifting into overdrive not possible)
Shift position indicator
Shows the selector lever position
Shift position is also displayed
on the instrument cluster
Driving pattern selector switch
For selecting a driving pattern suitable
to existing driving conditions
NORMAL position
for general driving
conditions
POWER position
for powerful acceleration
123
AUTOMATIC TRANSMISSION

STARTING AND DRIVING
124Your automatic transmission has a shift lock system to
minimize the possibility of incorrect operation. This means you
can only shift out of “P” position when the brake pedal is
depressed (with the ignition switch in “ON” position and the
lock release button pressed in).
Correct use of the automatic transmission is explained in the
following parts.
(a) Normal driving
(b) Using engine braking
(c) Using the “2” and “L” positions
(d) Backing up
(e) Parking
(f) Good driving practice
(g) If you cannot shift the selector lever out of “P” position
(h) If the “O / D OFF” indicator light flashes
(a) Normal driving
“P” (Park)
position
“N” (Neutral)
position
1. Start the engine as instructed in “How to start the
engine” on page 121.
The transmission must be in “P” or “N”. The engine will not start
in “R”, “2”, “L” or “D” position even if the key is turned to
“START”.
Driving pattern
selector switchIndicator light
Power position
Normal position
2. Set the driving pattern selector switch to the NORMAL
position.
Your transmission has a driving pattern selector switch which
allows you to select either “NORM” or “PWR” to suit your
driving condition. For ordinary driving, Lexus recommends that
you use the NORMAL position to improve fuel economy.
3. For more powerful acceleration and sporty driving, use
the POWER position.
In the POWER position, the “ECT PWR” light in the instrument
cluster is on and the transmission is shifted up at higher vehicle
speeds and shifted down more responsively than in the
NORMAL position.

STARTING AND DRIVING
128
(f) Good driving practice

If the transmission repeatedly upshifts and downshifts
between the third and overdrive gears when climbing a
gentle slope, it is suggested that the overdrive switch be
turned off. Be sure to turn the switch on immediately
afterward.

When towing a trailer, in order to maintain efficient engine
braking and electrical charging performance, do not use
overdrive.
CAUTION:
Always keep your foot on the brake pedal while stopped
with the engine running. This prevents the vehicle from
creeping.
NOTICE:
Do not hold the vehicle on an upgrade with the
accelerator pedal. This can cause the transmission to
overheat. Always use the brake pedal or parking brake.
(g) If you cannot shift the selector lever out
of “P” position
If you cannot shift the selector lever from “P” position even
though the brake pedal is depressed, use the shift lock
override button. For instructions, see “If you cannot shift
automatic transmission selector lever” on page 163.
(h) If the “O / D OFF” indicator light flashes
If the “O / D OFF” indicator light flashes, contact your Lexus
dealer as soon as possible. There may be trouble in the
transmission system.
CRUISE CONTROL
The cruise control allows you to cruise the vehicle at a
desired speed over 40 km / h (25 mph) with your foot off the
accelerator pedal.
Your cruising speed can be maintained although a slight speed
change may occur when driving up or down a gradient, within
the limits of engine performance. On steeper hills, a greater
speed change will occur so it is better to drive without the cruise
control.
When the cruise control is on, the driving pattern of the
automatic transmission is fixed in the normal position,
regardless of the position of the selector switch.
CAUTION:

To help maintain maximum control of your vehicle, do
not use the cruise control when driving in heavy or
varying traffic, or on slippery (rainy, icy or
snow-covered) or winding roads.

Avoid vehicle speed increases when driving downhill.
Use engine braking by downshifting the transmission.

STARTING AND DRIVING
135 CAUTION:
Under certain slippery road conditions, full stability of the
vehicle and power to the rear wheels cannot be
maintained, even though the traction control system is in
operation. In situations where the road surface is covered
with ice or snow, your vehicle should be fitted with snow
tires or tire chains and driven at a more cautious pace.
BRAKE SYSTEM
The tandem master cylinder brake system is a hydraulic
system with two separate sub-systems. If either sub-system
should fail, the other will still work. However, the pedal will be
harder to press, and your stopping distance will be longer.
Also, the brake system warning light may come on.
CAUTION:
Do not rely on a single brake system. Have your brakes
fixed immediately.
Brake booster
The brake booster uses engine vacuum to power-assist the
brakes. If the engine should quit while you are driving, you can
bring the vehicle to a stop with normal pedal pressure. There
is enough reserve vacuum for one or two stops but no more!
CAUTION:

Do not pump the brake pedal if the engine stalls. Each
push on the pedal uses up your vacuum reserve.
Even if the power assist is completely lost, the brakes
will still work. But you will have to push the pedal hard
− much harder than normal. And your braking distance
will be longer.
Anti-lock brake system
The anti-lock brake system is designed to prevent lock-up
of the wheels during sudden braking or braking on
slippery surfaces. This helps the vehicle remain steerable
and stable under these circumstances.
The system functions with normal pedal operation. When the
anti-lock function is in action, pulsation of the brake pedal may
occur, together with a characteristic noise. This indicates that
the system is functioning properly.
The anti-lock brake system comes into operation when the
vehicle is accelerating and the vehicle speed reaches
approximately 10 km / h (6 mph). It stops operating when the
vehicle is decelerating and the vehicle speed falls below
approximately 5 km / h (3 mph).
You may hear a sound in the engine compartment for a few
seconds just after the vehicle is started. This means that the
anti-lock brake system is in the self-check mode, and does not
indicate malfunction.
Even though the anti-lock brake system is operating, full
stability of the vehicle cannot be maintained for certain slippery
road conditions or high speed driving when cornering. Even
with the anti-lock brake system installed, it is still important, to
drive with all due care.

STARTING AND DRIVING
136Always maintain a safe distance from the vehicle in front of
you. Compared with vehicles not fitted with an anti-lock brake
system, your vehicle requires a longer stopping distance in the
following cases:

Driving on rough, gravel or snow-coverd roads.

Driving with tire chains installed.

Driving on roads where the road surface is pitted or has
other differences in surface height.
Avoid high speeds on wet roads. The anti-lock brake system
cannot eliminate the risk of aquaplaning.
Anti-lock brake system warning light
This light comes on when the ignition key is turned to the
“ON” position. After a few seconds, the light will go off.If either of the following conditions occurs, this indicates a
malfunction somewhere in the parts monitored by the warning
light system. Contact Your Lexus dealer as soon as possible
to service the vehicle.

The light does not come on as described above, or remains
on.

The light comes on while driving.
Even if the anti-lock brake system should fail, the brake system
will still operate conventionally. Have your vehicle checked by
your Lexus dealer as soon as possible.
Drum-in-disc type parking brake system
Your vehicle has a drum-in-disc type parking brake system.
This type of brake system needs bedding-down of the brake
shoes periodically or whenever the parking brake shoes
and / or drums are replaced.
Have your Lexus dealer perform the bedding-down.