seat adjustment lexus LS400 1995 Engine / 1995 LS400: COMFORT ADJUSTMENT

COMFORT ADJUSTMENT
80
Fully extend the shoulder belt to put it in the lock mode.
Place the shoulder bolt between the vehicle seatback and the
child restraint system and allow it to retract. To hold the child
restraint system securely, let the shoulder belt retract as far as
it will go while firmly pushing down the child restraint system.
If your child restraint system requires the use of a top strap,
latch the hook onto the anchor bracket and tighten the top
strap.

COMFORT ADJUSTMENT
82INSTALLATION ON FRONT SEAT
Do not use a child restraint system which requires use of a top
strap in the front seat. A child restraint system which requires
use of a top strap should only be installed in the rear seat.
CAUTION

Do not use a rear−facing child restraint system in the
front seat because the force of the rapid inflation of
the passenger airbag may cause severe injury to the
child.
Move fully back

When using a forward−facing child restraint system,
move the seat as far back as possible.

COMFORT ADJUSTMENT
83
Faster the lap and shoulder belt over the child restraint system
following the instructions provided by its manufacturer. Keep
the lap portion of the belt tight.
Fully extend the shoulder belt to put it in the lock mode.
Place the shoulder belt between the vehicle seatback and child
restraint system and allow it to retract. To hold the child
restraint system securely, let the shoulder belt retract as far as
it will go while firmly pushing down the child restraint system.

COMFORT ADJUSTMENT
85
DRIVING POSITION MEMORY
SYSTEM
The micro computer can memorize the position of the driver’s
seat, the height of the shoulder belt anchor of the driver’s seat
belt, and the positions of the tilt and telescopic steering, and
outside rear view mirrors. Two different driving position profiles
can be entered into the computer’s memory.
Recording a driving position in the computer’s memory can
only be done when the ignition key is in the “ON” position and
the shift lever is in the “P” position.
Setting a driving position
1. Adjust the driver’s seat, driver’s shoulder belt anchor,
tilt and telescopic steering and outside rear view mirrors
to the desired position.
2. While pushing the “SET” button, push button “1” or “2”
until the signal beeps.
The beep sound means that true positions are recorded in the
computer’s memory.
By repeating these two steps and pressing the remaining
button, the driving position for another driver can be recorded.
To set a new memorized position, select the desired position
and perform step 2. The previous memory will be erased and
the new position will be set.
To make only slight changes to an already memorized position,
the easiest way is to first activate the memorized position, then
make the desired changes and perform step 2 above.

COMFORT ADJUSTMENT
86
Activating a memorized position
When you push button “1” or “2”, the driving position will
be automatically adjusted to the position recorded for that
button.
Conditions for memorized position activation

Ignition key “ON” and shift lever in “P” position
All parts of the memorized positions can be activated.
However, if the brake pedals being depressed, the sear
position will not change.

Key not in ignition switch and within 30 seconds of opening
driver’s door.
The memorized position can be activated, except for the tilt
and telescopic steering. This will be activated when the key
is inserted into the ignition switch.
If any driving position memory switch is pushed while one of
the memorized driving position profiles is being activated, the
operation will stop.To activate the system, push the desired button (“1” or “2”)
again.
The driving position memory control system cannot be
operated while the vehicle is moving.
If the vehicle’s battery is disconnected, the computer’s
memory will be erased and the memorized positions will have
to be set again.
CAUTION

Do not start the vehicle while the adjustments are
being made.

Take care not to select the wrong button, or the seat
could strike the rear passenger or hit your body
against the steering wheel. If this happens, you can
stop the movement by pressing another driving
position memory switch, or depressing the brake
pedal.