Battery lexus LS400 1998 Engine / LEXUS 1998 LS400 (OM50498U) User Guide

INTERIOR EQUIPMENT
58
PENLIGHT
14L014
The penlight is in the tool box on the right side of the trunk.
Battery insertion: Insert the batteries into the penlight. (The
penlight terminals have no + or end, but be sure to insert both
batteries facing the same direction.)
To turn the penlight on, turn the penlight head.
To turn it off, turn the penlight head further in the same direction
or turn it in the reverse direction.
FLOOR MAT
14L034
Use a floor mat of the correct size.
If the floor mat has a hole, then it is designed for use with a locking
clip. Fix the floor mat and locking clip into the hole in the floor
carpet.

EXTERIOR EQUIPMENT
66
CAUTION
Make sure the cap is tightened securely to prevent fuel
spillage in case of an accident.
Use only a genuine Lexus fuel tank cap for replacement. It
has a builtin check valve to reduce fuel tank vacuum.
In case the opener is not actuated
15L008-2
Pull the manual lever toward the back.
This is used in case the fuel filler door cannot be opened due to a
discharged battery or other trouble.
MOON ROOF
15L0241
1
Open 2
Close
To slide open the moon roof, push the switch toward the back for
about 1 second. The moon roof will fully open. To stop partway,
push the same switch or push the ”TILT” switch.
The sun shade can be opened or closed manually. However, if you
open the moon roof, the sun shade will be opened with the moon
roof.
To close the moon roof, push the switch toward the front for
about 1 second. The moon roof will fully close. To stop partway,
push the same switch or push the ”TILT” switch.

COMFORT ADJUSTMENT
97
16L036-6
In the following cases, contact your Lexus dealer as soon as possible:
Any of the SRS airbags have been inflated.
If either front seat belt does not retract or cannot be pulled out due
to a malfunction or activation of the pretensioner.The front seat belt retractor assembly or surrounding area has
been damaged.
The front part of the vehicle and portion of the doors (shaded in
the illustration) were involved in an accident that did not cause the
SRS to work.
The surface of the seats with the side airbags or the pad section
of the steering wheel or front passenger airbag cover (shaded in
the illustration) is scratched, cracked, or otherwise damaged.
NOTICE
Do not disconnect the battery cables before contacting your
Lexus dealer.

COMFORT ADJUSTMENT
114The beep sound means that the positions are recorded in the
computer ’s memory.
By repeating these two steps and pressing the remaining button, the
driving position for another driver can be recorded.
To set a new memorized position, select the desired position and
perform step 2. The previous memory will be erased and the new
position will be set.
To make only slight changes to an already memorized position, the
easiest way is to first activate the memorized position, then make the
desired changes and perform step 2 above.
Activating a memorized position
16L056
When you push button ”1” or ”2”, the driving position will be
automatically adjusted to the position recorded for that button.Conditions for memorized position activation
Ignition key ”ON” and shift lever in ”P” position.
All parts of the memorized positions can be activated.
However, if the brake pedal is being depressed, the seat position
will not change.
Key not in ignition switch and within 30 seconds of opening
driver’s door.
The memorized position can be activated, except for the tilt and
telescopic steering.
If any driving position memory switch is pushed while one of the
memorized driving position profiles is being activated, the operation
will stop.
To activate the system, push the desired button (”1” or ”2”) again.
The driving position memory control system cannot be operated
while the vehicle is moving.
If the vehicle’s battery is disconnected, the computer’s memory will
be erased and the memorized positions will have to be set again.
CAUTION
Do not start the vehicle while the adjustments are being
made.
Take care not to select the wrong button, or the seat could
strike the rear passenger or hit your body against the
steering wheel. If this happens, you can stop the movement
by pressing another driving position memory switch, or
depressing the brake pedal.

THEFT DETERRENT
117
THEFT DETERRENT SYSTEM
To deter theft of the vehicle, this system is designed to give an
alarm if any of the doors, trunk or hood is forcibly unlocked or
the battery terminal is disconnected and then reconnected while
the vehicle is locked.*
NOTE: *The system operating condition can be changed. Ask
your Lexus dealer for details.
The alarm blows the horn intermittently and flashes the headlights,
tail lights and other exterior lights.
17L001
Setting the system
1. Turn the ignition key to the ”LOCK” position and remove it.
2. Close and lock all the doors, trunk and hood using an ignition
key or wireless remote control.If you lock them with wireless remote control, the turn signals flash
once.* If you do not want to make them flash, consult with your
Lexus dealer.
NOTE: *The turn signals can be set not to flash. Ask your Lexus
dealer for details.
The indicator light will come on when all the doors, trunk and hood
are closed and locked.
3. After 30 seconds, the indicator flashes and the system is set.
Cancelling the system
When you unlock any door or trunk using an ignition key or
wireless remote control, the system is cancelled.
If you unlock any door or trunk with wireless remote control, the turn
signals flash twice.* If you do not want to make them flash, consult
with your Lexus dealer.
NOTE: *The turn signals can be set not to flash. Ask your Lexus
dealer for details.
Activating the system
The alarm sounds for 60 seconds if any of the following are operated:
Unlocking any door or trunk without using an ignition key or
wireless remote control.
Opening the hood forcibly.
Reconnecting the battery.

THEFT DETERRENT
118If any door is unlocked and the ignition key is not in the ignition
switch during the alarm sounding, its door is automatically locked.
To stop the alarm: Use either of the following methods.
Unlock the door or trunk using an ignition key or wireless remote
control.
Turn the ignition switch on.
Testing the system
1. Open all the windows.
2. Set the system as described above.
The front doors should be locked with the ignition key or wireless
remote control. Be sure to wait until the indicator light starts
flashing.
3. Unlock one of the doors from the inside.
The system should activate the alarm.
4. Unlock any of the doors with a key or the wireless remote
control to cancel the system.
5. Repeat this operation for the other doors and hood.
When testing the hood, also check that the system is activated when
the battery terminal is disconnected and then reconnected.
If the system does not work properly, have it checked by your Lexus
dealer.
NOTICE
Disconnecting the battery may result in the erasure of
information you have set in the computer memory. After
reconnecting the battery, check that the memorized data has
been retained. If it has been erased, input it into the computer
once more.

AIR CONDITIONING AND AUDIO
121
AUTOMATIC AIR CONDITIONING CONTROLS
21L001-5
The automatic air conditioning automatically maintains the set
temperature.
This air conditioning features automatic fan speed and air flow
control which automatically selects the most suitable fan speed
and air flow to control the temperature. The ignition key must be
in the ”ON” position.NOTICE
To prevent the battery from being discharged, do not leave the air
conditioning on longer than necessary when the engine is not
running.

AIR CONDITIONING AND AUDIO
128
(b) Windshield defogging and defrosting
21L009-3
To remove interior fog on the windshield
Push the”FRONT WINDSHIELD” button.
To remove frost or exterior fog on the windshield
1. Place the temperature control button at the maximum
temperature.
2. Push the ”FRONT WINDSHIELD” button.
3. Push the fan speed control button on the right side to obtain a
maximum air flow.
4. Leave the air conditioning onoff button off.When the ”FRONT WINDSHIELD” button is pushed while
operating in automatic mode, the air conditioning is set to operate
and the OUTSIDE AIR mode is set.
If you push the ”FRONT WINDSHIELD” button once again while
in the FRONT WINDSHIELD mode, the mode then returns to the
last mode used.
CAUTION
Do not use the ”FRONT WINDSHIELD” button during
cooled air operation in extremely humid weather. The
difference between the temperature of the outside air and that
of the windshield could cause the outer surface of the
windshield to fog up blocking your vision.
When you turn the ignition switch on after the removal and
installation of the battery terminal, the indicator light may flash and
the operating sound of the motor may be heard. This does not
indicate a malfunction.
You may hear the operating sound of the motor about 70 seconds
after the ignition switch is turned off. This is not also a malfunction.

AIR CONDITIONING AND AUDIO
134
Using your audio system: some basics
This section describes some of the basic features of the Lexus audio
system. Some information may not pertain to your system.
Your audio system works when the ignition key is in the ”ACC” or
”ON” position.
NOTICE
To prevent the battery from being discharged, do not leave the
car audio on longer than necessary when the engine is not
running.
(a) Turning the system on and off
20L002-1
Push this knob to turn the audio system on and off. Turn this
knob to adjust the volume.
The system turns on in the last mode used.
20L042-2
Push ”AM”, ”FM1/2”, ”TAPE” or ”CD” to turn on that mode.
The selected mode turns on directly.
Push these buttons if you want to switch from one mode to another.
If the tape or disc is not set, the cassette player or compact disc player
does not turn on.
You can turn off the cassette player by ejecting the cassette tape. If
the audio system was previously off, then the entire audio system
will be turned off when you eject the cassette tape. If another
function was previously playing, it will come on again.

AIR CONDITIONING AND AUDIO
138
20L0461
Push this button on the upper side to step up the station band or
on the lower side to step down.
Your radio automatically changes to stereo reception when a stereo
broadcast is received. ”ST” appears on the display. If the signal
becomes weak, the radio reduces the amount of channel separation
to prevent the weak signal from creating noise. If the signal becomes
extremely weak, the radio switches from stereo to mono reception.
In this case, ”ST” disappears from the display.(b) Presetting a station
20L047-1
1. Tune in the desired station.
2. Push one of the station selector buttons ( 16 ) and hold it until
a beep is heard. This sets the station to the button and the button
number ( 16 ) appears on the display.
Each button can store one AM station and two FM stations. To
change the preset station to a different one, follow the same
procedure.
The preset station memory is cancelled when the power source is
interrupted by battery disconnection or a blown fuse.