lock LEXUS LS430 2005 Owners Manual

STARTING AND DRIVING
298
BEFORE STARTING THE ENGINE
1. Check the area around the vehicle before entering it.
2. Adjust seat cushion length, seat position, seatback angle,
seat cushion angle, seat cushion height, head restraint height
and steering wheel angle.
3. Adjust the inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts.
Remember to check that the service reminder indicators
function when turning the ignition switch to “ON”, and check the
fuel gauge to see that you have sufficient fuel.
SMART IGNITION SWITCH WITH STEERING LOCK
31L345a
Carrying a smart key allows you to start the engine
without the key being inserted into the ignition switch.
The smart key system can be deactivated using a key cancel
switch. For details, see “Deactivating the smart key system”
on page 34.

STARTING AND DRIVING
299
31L346a
When you enter the vehicle carrying a sm art key and push
the ignition switch, the electronic code in the key is
automatically checked as to whether it corresponds to the
registered ID code for the vehicle. The key indicator light
comes on, the steering column lock is released, and the
engine immobilizer system is cancelled.
At this time, the security indicator light goes off and you can
start the engine when you turn the ignition switch and the key
indicator light does not come on. When you turn the ignition
switch, turn it slowly and surely. If you turn it quickly, it may
become stuck. To free it, see the following “If the ignition switch
seems to be stuck”.
If you push the ignition switch when the smart key is not within
the effective range of the smart key system, a warning tone
sounds and “Key is not Detected” appears on the display. If the ignition switch seems to be stuck:
To free the ignition switch, perform the following:
31L638
1. Push the ignition switch.
31L639
2. Be sure to push the ignition switch while turning the
steering wheel slightly in either direction, and then turn
the switch.

STARTING AND DRIVING
300“START” Starter motor on. The ignition switch will
return to the “ON” position when released.
For starting tips, see page 304.
“ON” Engine on and all accessories on.
This is the normal driving position.
NOTICE
Do not leave the ignition switch in the “ON” position if
the engine is not running. The battery will discharge
and the electronic ignition system could be damaged.
“ACC” Accessories such as the radio operate, but the
engine is off.
31L347
“LOCK” Engine is off and the steering wheel is locked.
When
you leave your vehicle, be sure to turn the ignition switch
to the “LOCK” position and carry the smart key.
 If you open the driver’s door without returning the ignition
switch to the “LOCK” position, beeps keep sounding while
the door is opened.
 If you close a door to leave your vehicle while carrying a key
on which the ignition switch has not been returned to the
“LOCK” position, “Key is not Detected” appears on the
multi−information display, a warning tone sounds inside and
beeps sound outside.
 If the selector lever is in a position other than “P”, you cannot
turn the ignition switch to the “LOCK” position. At this time,
when you open the driver’s door and are going to get out of
the vehicle, “Shift to P Range” appears on the
multi−information display and a warning tone sounds inside.

STARTING AND DRIVING
301
When you turn the ignition switch to the “LOCK” position, the
engine immobilizer system is automatically set. See “Engine
immobilizer system” on page 17.
If, in an emergency, you must turn the engine off while the
vehicle is moving, turn the ignition switch only to “ACC”.
IGNITION SWITCH WITH STEERING
LOCK
31L348
 1Type A 2Type B
Type A: Insert the key, push and turn it to each position.
Type B: Insert the key and turn it to each position.

STARTING AND DRIVING
303
“START” Starter motor on. The key will return to the
“ON” position when released.
For starting tips, see page 304.
“ON” Engine on and all accessories on.
This is the normal driving position.
NOTICE
Do not leave the key in the “ON” position if the engine
is not running. The battery will discharge and the
electronic ignition system could be damaged.
“ACC” Accessories such as the radio operate, but the
engine is off.
If you leave the key in the “ACC” or “LOCK” position and open
the driver’s door, a buzzer will remind you to remove the key.*
NOTE:
* The volume or interval of beep sound can be changed.
Ask your Lexus dealer for details.
31L349
 1 Type A 2Type B
“LOCK” Engine is off and the steering wheel is locked.
The ignition key can be removed only at this position.
To turn the ignition switch from “ACC” to the “LOCK” position,\
you must put the transmission selector lever in the “P” position.
Once you remove the key, the engine immobilizer system is
automatically set. See “Engine immobilizer system” on page
17.
If, in an emergency, you must turn the engine off while the
vehicle is moving, turn the key only to “ACC”.

STARTING AND DRIVING
305
The engine should be warmed up by driving, not in idle. For
warming
up, drive with smoothly turning engine until the engine
coolant temperature is within normal range.
If the engine stalls ...
Simply restart it, using the correct procedure given in normal
starting.
If the engine will not start
See “If your vehicle will not start” on page 400.
NOTICE
 Do not crank for more than 30 seconds at a time. This
may overheat the starter and wiring systems.
 Do not race a cold engine.
 If the engine becomes difficult to start or stalls
frequently, have the engine checked immediately.
AUTOMATIC TRANSMISSION
Your automatic transmission has a shift lock system to
minimize the possibility of incorrect operation. This
means you can only shift out of “P” position when the
brake pedal is depressed with the ignition switch in “ON”
position. ( )
31L320

STARTING AND DRIVING
315
(g) If you cannot shift the selector lever
If you cannot shift the selector lever even though the brake
pedal is depressed, use the shift lock override button. For
instructions, see “If you cannot shift automatic transmission
selector lever” on page 423.
ELECTRONIC THROTTLECONTROL SYSTEM
The electronic throttle control system always maintains
appropriate engine output in relation to the accelerator
opening in all driving conditions.
31L322
 1Power position 2Normal position
3Snow position
The electronic throttle control system has 3 modes:
Normal, Power and Snow modes.
Normal mode: For ordinary driving, Lexus recommends that
you use the normal mode to improve fuel economy.
Power mode: For more powerful acceleration and sporty
driving.

STARTING AND DRIVING
342In the following case, the preset speed automatically
cancels out. At this time, the multiinformation display
shows “RADAR READY” and the dynamic radar/laser
cruise control enters the ready mode.
The vehicle speed falls below about 40 km/h (25 mph). (40
km/h (25 mph) is designated as a cancel speed.)
CAUTION
In this case, the warning tone reminds you that the
dynamic
radar/laser cruise control is cancelled and you
must apply the brakes to slow the vehicle.
In the following cases, the warning messages appear and
the preset speed automatically cancels out. When
dynamic radar/laser cruise control is restored, the
warning messages turn off and dynamic radar/laser
cruise control enters “RADAR READY” mode.
a. The slip indicator light blinks and a warning tone sounds.
(This occurs when the vehicle is about to skid.)
b. The driving pattern selector switch is set to “SNOW” mode.
c. The anti −lock brake system is activated by automatic
braking. (The warning tone sounds.)
d. The sensor does not operate properly because a foreign
matter sticks to the sensor.
Dynamic radar cruise control—
e. The wipers are operated at high speed (including high
speed operation with the wiper lever in the “AUTO” position.)
Dynamic laser cruise control—
f. The wipers are operated at high or low speeds (including
high and low speed operations with the wiper lever in the
“AUTO” position.)

STARTING AND DRIVING
364
“Check VSC” warning message
31L337a
If the vehicle stability control system or the traction
control system malfunctions, the master warning light
and “TRAC OFF” indicator light come on. At this time a
warning tone sounds and the above message appears.
If the message appears, the vehicle stability control system
and traction control system do not work. Although it is no
problem to continue driving, have your vehicle checked by
your Lexus dealer as soon as possible.
VEHICLE STABILITY CONTROLSYSTEM
The vehicle stability control system helps provide
comprehensive control of the systems such as antilock
brake system, traction control, engine control, etc. This
system automatically controls the brakes and engine to
help prevent the vehicle from skidding when cornering on
a slippery road surface or operating steering wheel
abruptly.
This system activates when the vehicle speed is about more
than 15 km/h (9 mph).
You may hear a sound in the engine compartment for a few
seconds just after the vehicle begins to move. This means that
the system is in the self −check mode, but does not indicate a
malfunction.

STARTING AND DRIVING
367
Antilock brake system
The antilock brake system is designed to automatically
help prevent lockup of the wheels during a sudden
braking or braking on slippery road surfaces. This assists
in providing directional stability and steering
performance of the vehicle under these circumstances.
Effective way to press the ABS brake pedal: When the
anti−lock brake system function is in action, you may feel the
brake pedal pulsating and hear a noise. In this situation, to
let the anti−lock brake system work for you, just hold the
brake pedal down more firmly. Do not pump the brake in a
panic stop. This will result in reduced braking performance.
The anti −lock brake system becomes operative after the
vehicle has accelerated to a speed in excess of approximately
10 km/h (6 mph). It stops operating when the vehicle
decelerates to a speed below approximately 5 km/h (3 mph).
Depressing the brake pedal on slippery road surfaces such as
on a manhole cover, a steel plate at a construction site, joints
in a bridge, etc. on a rainy day tends to activate the anti −lock
brake system.
You may hear a click or motor sound in the engine
compartment for a few seconds when the engine is started or
just after the vehicle begins to move. This means that the
anti−lock brake system is in the self− check mode, and does not
indicate a malfunction. When the antilock brake system is activated, the
following conditions may occur. They do not indicate a
malfunction of the system:

You may hear the anti− lock brake system operating and feel
the brake pedal pulsating and the vibrations of the vehicle
body and steering wheel. You may also hear the motor
sound in the engine compartment even after the vehicle is
stopped.
 At the end of the anti−lock brake system activation, the
brake pedal may move a little forward.
CAUTION
Do not overestimate the antilock brake system:
Although the antilock brake system assists in
providing vehicle control, it is still important to drive
with all due care and maintain a moderate speed and
safe distance from the vehicle in front of you, because
there are limits to the vehicle stability and effectiveness
of steering wheel operation even with the antilock
brake system on.
If tire grip performance exceeds its capability, or if
hydroplaning occurs during high speed driving in the
rain, the antilock brake system does not provide
vehicle control.