door lock LEXUS LS430 2005 Workshop Manual

INTERIOR EQUIPMENT
131
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, always keep the auxiliary boxes closed
while driving.
TRUNK STORAGE EXTENSION
14L241
 1Type A 2Type B
3Unlock 4Lock 5Open
Pull down the center armrest in the rear seat. Pull the lever
and open the door.
Be sure to use “LEXUS Genuine Sports Gear, Bag” or carry
long objects (ski boards, poles, etc.) properly.
For installation and handling of the “LEXUS Genuine Sports
Gear”, follow the instructions provided with goods.
You can use a container as an accessory box. To lock the box,
insert the master key and turn it clockwise.

INTERIOR EQUIPMENT
132
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, always keep the container closed while
driving.
14L223
 1From passenger compartment side
2From trunk side
To extend a storage space, push the button on the door to
unlock and then push the door from the passenger side or pull
it from the trunk side.
See “Cargo and luggage” on page 394 for precautions to
observe in loading luggage.
CAUTION
Be sure to close the door when the trunk storage
extension is not in use. Luggage or cargo in the trunk
may be thrown into the passenger compartment in a
sudden stop or crash resulting in injury.

EXTERIOR EQUIPMENT
143
TRUNK LID
15L096a
 1Type A 2Type B
To unlock the trunk lid, insert the master key and turn it
clockwise.
To close the trunk lid, lower it and press down on it. After
closing the trunk lid, try pulling it up to make sure it is securely
closed.
The trunk lid can be unlocked by pushing the trunk button or
using the wireless remote control function. For details, see
“Smart key system” on page 20 and “Wireless remote control”
on page 36.
When you open the trunk, the lights illuminate the inside of the
trunk and around your feet.
CAUTION
 Keep the trunk lid closed while driving. This not only
prevents luggage from being thrown out, but also
prevents exhaust gases from entering the vehicle.
 Always lock the trunk lid and all doors, and keep the
vehicle keys out of children’s reach .
 Never leave children unattended in the vehicle.
Unsupervised children may lock themselves in the
vehicle or trunk and suffer serious injuries or death.

EXTERIOR EQUIPMENT
147
15L037b
2. To remove the fuel tank cap, turn the cap slowly
counterclockwise, then pause slightly before removing it.
The removed cap can be stored on the back side of the fuel
filler door.
It is not unusual to hear a slight swoosh when the cap is
opened. When installing the cap, turn the cap clockwise until
you hear a click.
If the cap is not tightened securely, the malfunction indicator
lamp comes on. Make sure the cap is tightened securely.
The indicator lamp goes off after driving several times. If the
indicator lamp does not go off, contact your Lexus dealer as
soon as possible.
CAUTION
 Make sure the cap is tightened securely to prevent
fuel spillage in case of an accident.
 Use only a genuine Lexus fuel tank cap for
replacement. It is designed to regulate fuel tank
pressure.
NOTICE
To prevent damage to the cap, observe the following
precautions.
Apply force only in the turning direction to the cap.
Do not pull or pry it.
 Do not tighten the cap further after you hear one click
when installing.

EXTERIOR EQUIPMENT
149
To close the moon roof, push the slide control switch
toward the front for about 1 second. The moon roof will
fully
close. To stop partway, push the same switch or push
the “TILT” switch.
15L087
 1 Tilt up 2Lower
To tilt up the moon roof, push the “TILT” switch on the rear
side. The moon roof will fully tilt up. To stop partway, push
either side of the “TILT” switch.
To lower the moon roof, push the “TILT” switch on the
front side. The moon roof will be fully lowered. To stop
partway, push either side of the “TILT” switch.
To operate the moon roof, the ignition switch must be in the
“ON” position.
Retained accessory power: Even if the ignition switch is
turned to the “ACC” or “LOCK” position, the moon roof can be
operated until any of the doors is opened (or for about 45
seconds).
Operating the moon roof from outside the
vehicle
The moon roof can be closed or opened using a key.*
NOTE:
* This feature can be deactivated, or sliding open or tilting
up can be selected.
Ask your Lexus dealer for details.
15L093
Type A

EXTERIOR EQUIPMENT
150
15L094
Type B
Insert the key into the key hole on the driver’s door.
To close the moon roof: Turn the key in the locking direction
and hold it.
After the door is locked, the moon roof begins to close. To stop
in the middle, return the key.
To slide open the moon roof: Turn the key in the unlocking
direction and hold it.
After the door is unlocked, the moon roof begins to open. To
stop in the middle, return the key.
Jam protection function
During closing operation, the moon roof stops and is open if
something gets caught into the roof opening.
If the moon roof receives a strong impact, this function may
work even if nothing is caught.
CAUTION
To avoid serious personal injury, you must do the
following.
 While the vehicle is moving, always keep the heads,
hands and o ther parts of the bodies of all occupants
away from the roof opening. Otherwise, they could
be seriously injured if the vehicle stops suddenly or
if the vehicle is involved in an accident.
 Before you close the moon roof, always make sure
there is nobody around the moon roof. You must also
make sure nobody places his or her head, hands and
other parts of the body in the roof opening. If
someone’s neck, head or hands get caught in the
closing roof, it could result in death or serious injury.
When anyone closes the moon roof, first make sure
it is safe to do so.
 Be sure to remove the ignition key or turn the ignition
switch to the “LOCK” position when you leave your
vehicle.

OCCUPANT RESTRAINT SYSTEMS
169
Be careful not to damage the belt webbing or
hardware. Take care that they do not get caught or
pinched in the seat or doors.
 Inspect the belt system periodically. Check for cuts,
fraying, and loose parts. Damaged parts should be
replaced. Do not disassemble or modify the system.
 Keep the belts clean and dry. If they need cleaning,
use a mild soap solution or lukewarm water. Never
use bleach, dye, or abrasive cleaners, or allow them
to come into contact with the belt they may severely
weaken the belts. (See “Cleaning the interior” on
page 515 for instructions.)
 Replace the belt assembly (including bolts) if it has
been used in a severe impact. The entire assembly
should be replaced even if damage is not obvious.Front seat belt buckle illumination
16L371
Opening the driver’s door lights up the driver’s seat belt
buckle for easy use. The same applies for the front
passenger’s door and seat belt buckle.
The light remains on for 15 seconds after the door is closed,
but goes off immediately when all the doors are locked.

OCCUPANT RESTRAINT SYSTEMS
222Conditions for memorized position activation

Ignition switch “ON” and selector lever in “N” or “P” position
with the vehicle stopped.
All parts of the memorized positions can be activated.
 Ignition switch off and within 30 seconds of opening driver’s
door.
The memorized position can be activated, except for the tilt
and telescopic steering.
If any driving position memory switch is pushed while one of
the memorized driving position profiles is being activated, the
operation will stop.
To activate the system, push the desired button (“1”, “2” or \
“3”)
again.
The driving position memory control system cannot be
operated while the vehicle is moving.
CAUTION
 Do not start the vehicle while the adjustments are
being made.
 Take care not to select the wrong button, or the seat
could strike the rear passenger or hit your body
against the steering wheel. If this happens, you can
stop the movement by pressing another driving
position memory switch.
MEMORY CALL SYSTEM USING A SMART KEY
This system allows you to adjust the driver’s seat, the
driver’s head restraint height, driver’s seat cushion
length, the height of the shoulder belt anchor of the
driver’s seat belt and outside rear view mirrors to the
memorized position when you open the driver’s door after
unlocking it with a smart key. And when you push the
ignition switch, the tilt and telescopic steering is adjusted.
To activate this system, the ID of the smart key needs to
be registered in the memory button.
Registering the smart key ID code
Before the registration of the ID of the smart key, the driving
position must be memorized in the memory button.
When registering, the driver’s door must be closed with the
ignition switch in the “OFF” position.
1. Keep the smart key in possession, select a button in
which you want to record the ID of the key from buttons
“1”, “2” and “3” and push it.
2. Push the “LOCK” or “UNLOCK” button on the smart
key for about one second with button “1”, “2” or “3” held\
down.
When the registration is completed, one beep sounds. If the
key has already been registered, the previous memory will be
erased. If the same driving position profile for the same key is
registered in another button, that memory will also be erased.

OCCUPANT RESTRAINT SYSTEMS
223
CAUTION
Do not push the “LOCK” button any longer than 2 or 3
seconds. Pushing the button longer activates an alarm.
For details, see page 40.
Erasing the previous registration memory
The driver’s door must be closed with the ignition switch in the
“OFF” position.
1. Keep the smart key in which you want to cancel the
registration in possession and push the “SET” button.
2. Push the “LOCK” or “UNLOCK” button on the smart
key for about one second with the “SET” button held
down.
When the previous key ID memory is erased, two beeps
sound.MEMORY CALL SYSTEM USING A WIRELESS REMOTE
CONTROL KEY
This system allows you to adjust the driver’s seat, the
driver’s head restraint height, driver’s seat cushion
length, the height of the shoulder belt anchor of the
driver’s seat belt and outside rear view mirrors to the
memorized
position when you open the driver’s door after
unlocking it with a wireless remote control key. And when
you insert the key into the ignition switch, the tilt and
telescopic steering is adjusted.
To activate this system, the ID of the wireless remote
control key ne eds to be registered in the memory button.
Registering the wireless remote control key
ID code
Before the registration of the ID of the wireless remote control
key, the driving position must be memorized in the memory
button.
When registering, the driver’s door must be closed with the
ignition switch in the “OFF” position.
1. Keep the wireless remote control key in possession,
select a button in which you want to record the ID of the
key from buttons “1”, “2” and “3” and push it.
2. Push the “LOCK” or “UNLOCK” button on the wireless
remote control key for about one second with button “1”,
“2” or “3” held down.

OCCUPANT RESTRAINT SYSTEMS
224When the registration is completed, one beep sounds. If the
key has already been registered, the previous memory will be
erased. If the same driving position profile for the same key is
registered
in another button, that memory will also be erased.
CAUTION
Do not push the “LOCK” button any longer than 2 or 3
seconds. Pushing the button longer activates an alarm.
For details, see page 40.
Erasing the previous registration memory
The driver’s door must be closed with the ignition switch in the
“OFF” position.
1. Keep the wireless remote control key in which you want
to cancel the registrati on in possession and push the
“SET” button.
2. Push the “LOCK” or “UNLOCK” button on the wireless
remote control key for about one second with the “SET”
button held down.
When the previous key ID memory is erased, two beeps
sound.
REAR SEAT POSITION MEMORY SYSTEM
A microcomputer will memorize the position of the rear seats
and the height of the rear head restraints.
Recording the rear seat position in the computer’s memory can
only be done when the ignition switch is in the “ON” position.
Setting the rear seat position
16L301a
1. Adjust the rear seat position and the height of the head
restraint of the rear seat to the desired position.
2. Keep pushing the “SET” button until a beep sounds.
The beep sound means that the position has been memorized.
The memory will be erased when the battery is removed for
inspection or service.