low LEXUS LX470 2006 Owners Manual

STARTING AND DRIVING
281
Yes= The mode can be selected.
No = The mode cannot be selected.
Low
modeNormal modeHigh
mode
At vehicle
stoppageYe sYe sYe s
Under about 30
km/h (19 mph)NoYe sYe s
About 30 km/h
(19 mph) or overNoYe sNo
In the following cases the active height control
suspension does not operate even if the above conditions
are all met.
 The brake pedal has been depressed for longer than about
5 seconds with the vehicle stopped.
 The suspension fluid temperature is lower than −30 C
(−22 F). If the engine is warmed up, the suspension fluid
temperature will be raised as the inside of the engine
compartment becomes warmer. Then the active height
control suspension becomes operable.
 Driving on bumpy roads, which may cause the suspension
to fully elongate.
 The steering wheel is operated abruptly more than 3/4 turn
with center differential lock system activated.
(d) Vehicle height adjustment
31X049b
 1
Higher 2Lower
To change the mode, push the height select switch on
either side of “ ” and “
”.
The height control indicator light indicates which mode is
selected. (See page 284.)
NOTICE
 If you change the vehicle height frequently, the pump
may overheat. To prevent this, the active height
control suspension should be stopped temporarily
for a minute between selections. Operate it again.

STARTING AND DRIVING
282
Before you lower the vehicle height with the height
select switch, check under the vehicle to make sure
that nothing to damage the vehicle or no one to be
injured is there and the underbody of the vehicle
does not touch the ground.
 After unloading, the height of a vehicl e equipped with
the active height control suspension becomes
slightly higher than the normal vehicle height. Take
sufficient care where the overhead height is
restricted.
The vehicle height cannot be raised if the vehicle load
exceeds the following limits:
 Up to 4 occupants* plus about 300 kg (661 lb.) in the normal
mode
 Up to 4 occupants* plus about 170 kg (375 lb.) in the high
mode
*About 68 kg (150 lb.) for a person
If the above load capacity is exceeded, the desired vehicle
height may not be obtained even if the height select switch is
pushed. (If the vehicle height cannot be raised in the normal
mode and the height control indicator indicates “LO”, this is
because the vehicle is loaded too heavily. Under these
conditions, drive your vehicle with due care.)
If the vehicle height cannot be raised even after unloading,
push the height select switch on the “
” side and then on the
“ ” side. If this does not work, turn off the ignition once and
then turn on. Operate the select switch again. If the vehicle height is adjusted on the slope, or with the
selector lever in a position other than “P” or “N” while the\
vehicle is stopped, you may h
ear a sound caused by the
expansion and contraction of the propeller shaft.
 Selecting the high mode:
Push the height select switch on the “ ” side when the vehicle
speed is under about 30 km/h (19 mph).
To change the normal mode to high, push the switch once.
To change the low mode to high, push the switch twice. It
takes about 30 seconds until the low mode changes to the high
mode.
 Selecting the normal mode:
To change the high mode to normal, push the height select
switch on the “
” side once.
To change the low mode to normal, push the height select
switch on the “ ” side once.
 Selecting the low mode:
Push the height select switch on the “
” side while the vehicle
is stopped.
To change the high mode to low, push the switch twice.
To change the normal mode to low, push the switch once.

STARTING AND DRIVING
283
NOTICE
Do not select the low mode on bumpy roads. If the
underbody of the vehicle touches the rugged road
surface, the vehicle may be damaged.
Even if the engine is stopped while the vehicle height is
being lowered, the operation continues for up to 12
seconds.
(e) Turning off the active height controlsuspension
31X051d
To turn off the active height control suspension with the
vehicle stopped, push the height control switch. The
height control “OFF” indicator light comes on and the
vehicle height is fixed in the same mode as the height
control switch is pushed.
This status is memorized in the system even after the engine
is stopped.
If you push the switch again, the height control “OFF” indicator
light goes out and the active height control suspension is
turned on.

STARTING AND DRIVING
284
CAUTION
If you drive through deep water over about 500 mm (20
in.) in depth, put the vehicle height in the “HI” (High)
mode with the height select switch and then turn off the
active height control suspension by pushing the height
control switch. Drive your vehicle at 30 km/h (19 mph)
or lower speed.
NOTICE
 When jacking up or installing tire chains, be sure to
turn off the active height control suspension and
stop the engine. Otherwise, the vehicle height may
change because of the automatic leveling function,
resulting in an accident.
 If your vehicle must be towed, put the vehicle height
in the normal mode and turn off the active height
control suspension. Otherwise, the vehicle height
may change because of the automatic leveling
function, resulting in an accident.
 If your vehicle gets ditched, turn off the active height
control suspension with the height control switch.
Otherwise, the vehicle height may change because of
the automatic leveling function, resulting in an
accident.
Even after the active height control suspension is turned
off with the height control switch, if the vehicle speed
exceeds 30 km (19 mph), the active height control
automatically selects the normal mode.
(f) Height control indicator lights
31X050d
 1 Height control indicator lights
2Height control “OFF” indicator light
When the ignition switch is turned on, all the indicator
lights come on. The indicator light showing the present
mode only remains on and all other lights go off after a few
seconds. This means the system operates correctly.
If you change the vehicle height mode, the indicator lights
change as follows:

STARTING AND DRIVING
285
31X052a
: Blinking \f: Illuminating
When changing the vehicle height from the normal mode
to high:
1. The “N” (normal) mode indicator light goes off and the “HI”
(high) mode indicator light blinks.
2. After the vehicle height control reaches the high mode, the
high mode indicator light remains on.
With the active height control suspension turned off, if
you operate the height select switch or the vehicle height
is changing depending on the vehicle speed, the vehicle
height control enters the ready mode. In this case, the
height control indicator lights change as follows:
1. The present mode indicator light comes on and at the same
time the ready mode indicator light blinks.
2. When the active height control suspension is turned on, the
present mode indicator light goes off and the ready mode
indicator light blinks. (The vehicle height changes.) 3. After the vehicle height has changed completely, the
changed mode indicator light stays on.
If the vehicle is loaded heavily, the vehicle height cannot
be raised even if the height select switch is operated. If the
underbody of the vehicle has touched the surface on
bumpy roads, the vehicle height cannot be lowered with
the height select switch. The height control indicator
lights change as follows:
1. The present mode indicator light goes off and the selected
mode indicator light blinks.
2. The selected mode indicator light goes off. (The vehicle
height does not change.) The present mode indicator light
comes on again.
Height control “OFF” indicator light: When the ignition
switch is turned on, this light comes on. If it goes out after a few
seconds, the active height control suspension operates
correctly. If you push the height control switch, the active
height
control is turned off. The height control “OFF” indicator
light comes on.
In the following cases, there is a problem somewhere in your
active height control suspension. Although there is no problem
to continue normal driving, have the active height control
suspension checked by your Lexus dealer as soon as
possible.
 The height control “OFF” indicator light does not come on
when the ignition switch is turned on.
 The height control “OFF” indicator light blinks.

STARTING AND DRIVING
286
(g) Operation in cold weather
The active height control suspension does not operate in
cold weather when the suspension fluid temperature
drops below 30C (22F).
In this case, operating the height select switch does not
change the vehicle height. The vehicle height control enters
the ready mode and the selected height control indicator light
blinks. The active height control becomes operable if the
engine is warmed up with the suspension fluid temperature
being raised within normal operating limits. The vehicle
changes to the selected height when the vehicle height control
is in the ready mode.
When the suspension fluid temperature is around −30 C
(−22 F), the vehicle height cannot be raised even within the
available load capacity. After warming up the engine, push the
control switch on the “
” side once and then on the “ ” side
to select the desired vehicle height.
It takes longer to change the vehicle height when the
suspension fluid temperature drops below 15C (5F).
(h) Parking and stopping tips
If you immediately stop the engine to park the vehicle after
off−road driving, the vehicle height is lowered slightly as the
vehicle becomes cool. When parking, make sure there is
nothing that will be in contact with the underbody of the vehicle.
When you start the engine, the vehicle returns to the previous
height.
If you park the vehicle for a long time, the vehicle height may
gradually lower. When parking for a long time, make sure there
is nothing that will come in contact with the underbody of the
vehicle. When you start the engine, the vehicle returns to the
previous height.
If you stop the engine, the vehicle height may change in
accordance with the change in the temperature. When you
start the engine, the vehicle returns to the previous height.
(i) Installing or removing heavy equipment
If you install or remove heavy equipment exceeding 15 kg (33
lb.), the front torsion bar should be adjusted. Consult your
Lexus dealer.

STARTING AND DRIVING
290In the following cases, contact your Lexus dealer:

The “VSC/TRAC” warning light does not come on after the
ignition is turned to on.
 The “VSC/TRAC” remains on after the ignition is turned to
on.
CAUTION
Under certain slippery road conditions, full traction of
the vehicles and power to 4 wheels may not be
maintained, even though the active traction control
system is in operation. Do not drive the vehicle under
any speed or maneuvering conditions which will cause
the vehicle to lose traction. In situations where the road
surface is covered with ice or snow, your vehicle should
be fitted with snow tires or tire chains. Always drive at
an appropriate and cautious speed for the road
conditions present.
VEHICLE STABILITY CONTROL SYSTEM
31X504
The vehicle stability control system helps provide
integrated control of the systems such as antilock
brakes, traction control, engine control, etc. This system
automatically controls the output of the brakes or engine
to help prevent the vehicle from skidding under adverse
conditions.
When you turn the ignition switch on, the slip indicator light will
come on. The slip indicator light will go off after a few seconds.
If the vehicle is going to skid during driving, the slip indicator
light flashes and an alarm sounds intermittently.

STARTING AND DRIVING
292Depressing
the brake pedal repeatedly may turn on the lights.
It is normal if they go off after a few seconds.
When the “VSC/TRAC” warning light and “VSC OFF” indicator
light come on, the vehicle stability control system is not
operating, but there is no problem if you continue to drive.
In the following cases, contact your Lexus dealer:
 The “VSC/TRAC” warning light, “VSC OFF” indicator light
and slip indicator light do not come on after the ignition is
turned to on.
 The “VSC/TRAC” warning light and “VSC OFF” indicator
light remain on after the ignition is turned to on.
 The “VSC OFF” indicator light comes on while driving
without pushing the center differential lock switch.
CAUTION
Active traction control system, vehicle stability
control system and antilock brake system are
electronic systems designed to help the driver
maintain control under adverse conditions. They are
not a substitute for safe driving practices. Factors
including speed, road conditions and driver steering
input can all affect whether active traction control
system, vehicle stability control system and
antilock brake system will be effective in preventing
a loss of control. Always keep safety driving in mind.
If the slip indicator light flashes, sounding an alarm,
special care should be taken while driving.
 Only use tires of specified size. The size,
manufacturer, brand and tread pattern for all 4 tires
should be the same. If you use the tires other than
specified, or different type or size, the vehicle
stability control system may not function correctly.
When replacing the tires or wheels, contact your
Lexus dealer. (See “Checking and replacing tires” on
page 438.)

STARTING AND DRIVING
293
VARIABLE GEAR RATIO STEERINGSYSTEM
The variable gear ratio steering system adjusts the wheel
turning angle depending on the vehicle speed and how
much you turn the steering wheel.
The vehicle wheel turning angle will be changed with a smaller
degree of wheel maneuvering when you are driving at very low
speed such as when putting your vehicle into a garage.
In the following cases, to prevent the system from overheating,
the system could be temporarily deactivated with the change
in the center position of the steering wheel. This is not a
malfunction. After the cause of the problem is eliminated, the
system will return to normal automatically after a few minutes.
 If you continue maneuvering the steering wheel when the
vehicle is stopped or running at very low speed
 If you continue driving holding the steering wheel to the
extreme right or left
 If you maneuver the steering wheel immediately after
starting the engine at less than about −30C (− 22F) While the system is not functioning, a larger degree of wheel
maneuvering is needed during driving at low speed. If the
center position of the steering wheel is changed frequently,
have your vehicle inspected at your Lexus dealer.
CAUTION
Take due care especially when driving at low speed as
the vehicle changes direction in greater proportion to
the steering wheel maneuvering.
NOTICE
Do not disconnect the battery with the steering wheel
turned, or the center position of the steering wheel
could be slightly and temporarily changed. However,
after driving for a short while, the system will return to
normal
and the center position of the steering wheel will
be in the appropriate position.
The light will flash if you disconnect and reconnect the battery
terminal. This is because the system is reset temporarily.
However, it is no problem to drive. To turn off the light, drive for
a short while. The system will be set automatically and return
to normal.

STARTING AND DRIVING
294
Variable gear ratio steering system failure
warning
31x500b
This light warns that there is a problem somewhere in the
variable gear ratio steering system.
The light will come on when the ignition key is turned to “ON”
and will go off after a few seconds.
If the light comes on while driving, the system is not working.
Although conventional steering operates when maneuvered,
a larger degree of wheel maneuvering (than at the time when
the system is functioning properly) is needed when driving at
low speed. At this time, the center position of the steering
wheel could be changed. Although it is no problem to continue
driving, have your vehicle repaired at your Lexus dealer. In the following cases, contact your Lexus dealer.

The warning light does not come on after the ignition key is
turned to “ON”.
 The warning light remains on after the ignition key is turned
to “ON”.
 The warning light comes on while driving.