adding oil LEXUS NX300h 2018 Owners Manual

324 6-3. Do-it-yourself maintenance
LEXUS NX300h Owners Manu-
al_USA_OM78212U 6-3.Do-it-yourself maintenance
Do-it-yourself service pre-
cautions If you perform maintenance by
yourself, be sure to follow the cor-
rect procedure as given in these
sections.
Maintenance Items Parts and tools
12-volt Bat-
tery condition
( → P.333) •Grease
•Conventional wrench
(for terminal clamp
bolts)
Brake fluid
level
( → P.332) • FMVSS No.116 DOT 3
or SAE J1703 brake
fluid
• Rag or paper towel
• Funnel (used only for
adding brake fluid)
Engine/power
control unit
coolant level
( → P.330) • “Toyota Super Long Life
Coolant” or a similar
high quality ethylene gly-
col-based non-silicate,
non-amine, non-nitrite
and non-borate coolant
with long-life hybrid
organic acid technology
For the U.S.A.:
“Toyota Super Long Life
Coolant” is pre-mixed
with 50% coolant and
50% deionized water.
For Canada:
“Toyota Super Long Life
Coolant” is pre-mixed
with 55% coolant and
45% deionized water.
• Funnel (used only for
adding coolant) Engine oil
level
( → P.328) •“Toyota Genuine Motor
Oil” or equivalent
• Rag or paper towel
• Funnel (used only for
adding engine oil)
Fuses
( → P.349) • Fuse with same amper-
age rating as original
Light bulbs
( → P.353) •Bulb with same number
and wattage rating as
original
Headlight aim • Phillips-head screw-
driver
Radiator and
condenser
( → P.331) —
Tire inflation
pressure
( → P.343) • Tire pressure gauge
• Compressed air source
Washer fluid
( → P.332) • Water or washer fluid
containing antifreeze
(for winter use)
• Funnel (used only for
adding water or washer
fluid)
WARNING
The engine compartment contains many
mechanisms and fluids that may move
suddenly, become hot, or become elec-
trically energized. To avoid death or seri-
ous injury, observe the following
precautions.
■
When working on the engine com-
partment
●
Make sure that the indicator on the
power switch and the “READY” indi-
cator are both off.
●
Keep hands, clothing and tools away
from the moving fan and engine drive
belt. Items Parts and tools

328 6-3. Do-it-yourself maintenance
LEXUS NX300h Owners Manu-
al_USA_OM78212U ■
Removing the engine compart-
ment cover
■
Installing the clips
1 Insert
2 Press With the engine at operating tempera-
ture and turned off, check the oil level
on the dipstick. ■
Checking the engine oil
1 Park the vehicle on level ground.
After warming up the hybrid sys-
tem, and turning off the engine, wait
more than 5 minutes for the oil to
drain back into the bottom of the
engine.
2 Holding a rag under the end, pull
the dipstick out.
3 Wipe the dipstick clean.
4 Reinsert the dipstick fully with its
protruding areas ( in the illustra-
tion) pointing towards engine.Engine compartment cover
NOTICE
■
After installing an engine compart-
ment cover
Make sure that the cover is securely
installed in its original position. Checking and adding the engine
oil
A

3296-3. Do-it-yourself maintenance
LEXUS NX300h Owners Manu-
al_USA_OM78212U 6
Maintenance and care 5 Holding a rag under the end, pull
the dipstick out and check the oil
level.
Low
Normal
Excessive
Measuring side
6 Wipe the dipstick and reinsert it
fully. ■
Checking the oil type and prepar-
ing the items needed
Make sure to check the oil type and
prepare the items needed before add-
ing oil.
 Engine oil selection → P.402
 Oil quantity (Low Full) 1.6 qt. (1.5 L, 1.3 Imp.qt.)
 Items Clean funnel
■
Adding engine oil
If the oil level is below or near the low
level mark, add engine oil of the same
type as that already in the engine. 1 Remove the oil filler cap by turning
it counterclockwise.
2 Add engine oil slowly, checking the
dipstick.
3 Install the oil filler cap by turning it
clockwise. ■
Engine oil consumption
A certain amount of engine oil will be con-
sumed while driving. In the following situa-
tions, oil consumption may increase, and
engine oil may need to be refilled in
between oil maintenance intervals. ●
When the engine is new, for example
directly after purchasing the vehicle or
after replacing the engine ●
If low quality oil or oil of an inappropriate
viscosity is used ●
When driving at high engine speeds or
with a heavy load, when towing, or when
driving while accelera ting or decelerat-
ing frequently ●
When leaving the engine idling for a long
time, or when driving frequently through
heavy traffic
■
After changing the engine oil
The engine oil maintenance data should be
reset. Perform the fo llowing procedures:
1 Press or of the meter control
switches and select .A
B
C
D