air LEXUS RC300H 2017 Owners Manual

5548-2. Steps to take in an emergency
RC300h_EE(OM24740E)
Indicates that the engine oil is scheduled to be changed.
(The indicator will not work properly unless the message has been reset.) Check the engine oil, and change if necessary.
After changing the engine oil, the message should be reset.
Indicates that the engine oil should be changed. (Afterthe engine oil is changed and the message has been
reset.)  Check and change the engine oil, and oil filter by any authorized Lexus dealer or repairer, or another
duly qualified and equipped professional. After changing the engine oil, the message should bereset.
(If equipped)
Indicates that the Automatic High Beam switch ispressed while the headlights are in low beam.
 Turn the high beam on and press the Automatic High Beam switch again.
(If equipped)
Indicates that, since the VSC (Vehicle Stability Control)system was turned off, the pre-crash brake system oper-
ation is stopped Operation of the pre-crash brake assist is alsostopped.
 Turn the VSC on. (P. 307)
(If equipped)
Indicates that the PCS (Pre-Crash Safety system) is not currently functional because the grille cover or the sen- sor is dirty
 Check the grille cover and the sensor and clean them if they are dirty.
Warning messageDetails/Actions
(Flashes)

5558-2. Steps to take in an emergency
8
When trouble arises
RC300h_EE(OM24740E)
*: For the EV drive mode operating conditions: P. 221
Indicates that operation of large electricity consuming systems such as the air conditioning system are sus-
pended  Stop using unnecessary electric components to reduce electricity consumpt ion. Wait a while until
the electric power supply is restored.
Indicates that the EV drive mode is not available*The reason the EV drive mode is not available (the
vehicle is idling, hybrid battery [traction battery] charge is low, speed is higher than the EV drive modeoperating speed range, accelerator pedal is
depressed too much) may be displayed. A buzzer also sounds. Use the EV drive mode when it becomes available.
Indicates that the EV drive mode has been automatically
canceled*
The reason the EV drive mode is not available (the hybrid battery [traction batter y] charge is low, speed is
higher than the EV drive mode operating speed range, accelerator pedal is depressed too much) maybe displayed.
A buzzer also sounds.  Drive the vehicle for a while.
Warning messageDetails/Actions
(Except F SPORT models) (F SPORT models) (Flashes) (Flashes)

5608-2. Steps to take in an emergency
RC300h_EE(OM24740E)
Once
Indicates a malfunction in the smart
entry & start system  Have the vehicle inspected by any authorized Lexus dealer or
repairer, or another duly quali- fied and equipped professional.
Once
• When the doors were unlockedwith the mechanical key and thenthe power switch was pressed, the
electronic key could not be detected in the vehicle.• The electronic key could not be
detected in the vehicle even after the power switch was pressed twoconsecutive times.
 Touch the electronic key to the power switch while depressingthe brake pedal.
Once
During an hybrid system starting
procedure in the event that the elec- tronic key was not functioning prop-erly ( P. 580), the power switch
was touched with the electronic key.  Press the power switch within 10 seconds of the buzzer sounding.

Indicates that:
• With the power switch off, the doors were unlocked and then the
driver’s door was opened and closed• The power switch was turned to
ACCESSORY mode without starting the hybrid system• The shift lever was shifted to P or
N from another position with the power switch in ON mode. Press the power switch while
depressing the brake pedal.
Interior buzzerExteriorbuzzerWarning messageDetails/Actions
(Flashes)
(Flashes)

5638-2. Steps to take in an emergency
8
When trouble arises
RC300h_EE(OM24740E)
If you have a flat tire
Your vehicle is not equipped with a spare tire, but instead is equipped with an
emergency tire puncture repair kit.
A puncture caused by a nail or screw passing through the tire tread can be
repaired temporarily with the emergency tire puncture repair kit.
WARNING
■If you have a flat tire
Do not continue driving with a flat tire.
Driving even a short distance with a flat tire can damage the tire and the wheel beyond repair. Driving with a flat tire may cause a circumferential groove on the side wall. Insuch a case, the tire may explode when using the emergency tire puncture repair kit,
resulting in death or serious injury.

5648-2. Steps to take in an emergency
RC300h_EE(OM24740E)
●Stop the vehicle in a safe place on a hard, flat surface.
●Set the parking brake.
●Shift the shift lever to P.
●Stop the hybrid system.
●Turn on the emergency flashers. (P. 528)
●Check the degree of the tire damage.
A tire should only be repaired with
the emergency tire puncture repair
kit if the damage is caused by a nail
or screw passing through the tire
tread.
• Do not remove the nail or screw
from the tire. Removing the
object may widen the opening
and disenable emergency repair
with the kit.
• To avoid sealant leakage, move the vehicle until the area of the puncture, if
known, is positioned at the top of the tire.
■A flat tire that cannot be repaired with the emergency tire puncture repair kit
In the following cases, the tire cannot be repaired with the emergency tire puncture
repair kit. Contact any authorized Lexus dealer or repairer, or another duly qualified and equipped professional.
●When the tire is damaged due to driving without sufficient air pressure
●When the tire lost air pressure due to a crack or damage in the tire sidewall
●When the tire is visibly separated from the wheel
●When the cut or damage to the tread is 4 mm (0.16 in.) long or more
●When the wheel is damaged
●When 2 or more sharp objects, such as nails or screws, have passed through the tread on a single tire
●When there is more than one hole or cut in the damaged tire
●When the sealant has expired
Before repairing the vehicle

5658-2. Steps to take in an emergency
8
When trouble arises
RC300h_EE(OM24740E)
Location of the emergency tire puncture repair kit
Emergency tire puncture repair kit components
Hose
Air release cap
Air pressure gauge
Compressor switch
Power plug
Stickers
1
2
3
4
5
6

5668-2. Steps to take in an emergency
RC300h_EE(OM24740E)
Remove the 12-volt battery cover.
Remove the band and take out the
emergency tire puncture repair kit.
Taking out the emergency tire puncture repair kits
1
2

5678-2. Steps to take in an emergency
8
When trouble arises
RC300h_EE(OM24740E)
Take out the repair kit from the tool box.
Remove the valve cap from the valve
of the punctured tire.
Remove the protective film from the
bottle and extend the hose. Remove
the air release cap from the hose.
Attach the sticker enclosed with the bot- tle on the specified locations. (See step
9.)
You will use the air release cap again. Therefore keep it in a safe place.
Connect the hose to the valve.
Screw the end of the hose clockwise asfar as possible.
Make sure that the compressor
switch is off.
Emergency repair method
1
2
3
4
5

5688-2. Steps to take in an emergency
RC300h_EE(OM24740E)
Remove the power plug from the
compressor.
Connect the power plug to the power outlet socket. ( P. 456)
Remove the sticker.
Attach the 2 stickers as shown.
Remove any dirt and moisture from the
wheel before attaching the label. If it is impossible to attach the label, make sureto tell any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional when you havethem repair and replace the tire that
sealant is injected.
6
7
8
9

5708-2. Steps to take in an emergency
RC300h_EE(OM24740E)
Inflate the tire until the specified air
pressure is reached.
The sealant will be injected and the
pressure will surge and then gradu-
ally decrease.
The air pressure gauge will display
the actual tire inflation pressure
about 1 minute (5 minutes at low
temperature) after the switch is
turned on.
Inflate the tire until the specified air
pressure.
• Turn the compressor switch off and
then check the tire inflation pressure.
Being careful not to over inflate,
check and repeat the inflation pro-
cedure until the specified tire infla-
tion pressure is reached.
• If the tire inflation pressure is still lower than the specified point after inflation
for 35 minutes with the switch on, the ti re is too damaged to be repaired. Turn
the compressor switch off and contact any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional.
• If the tire inflation pressure exceeds th e specified air pressure, let out some air
to adjust the tire inflation pressure. ( P. 573, 604)
With the compressor switch off, disconne ct the hose from the valve on the tire
and then pull out the power plug from the power outlet socket.
Some sealant may leak wh en the hose is removed.
Install the valve cap onto the valve of the emergency repaired tire.
Attach the air release cap to the end
of the hose.
If the air release cap is not attached, the sealant may leak and the vehicle may
get dirty.
14
1
2
3
15
16
17