door lock LEXUS RX200T 2017 Manual Online

6097-3. Do-it-yourself maintenance
7
Maintenance and care
RX350/RX200t_EE_OM48F32E
■Before recharging
When recharging, the battery produces hydr ogen gas which is flammable and explosive. Therefore, observe the following precautions before recharging:
●If recharging with the battery installed on the vehicle, be sure to disconnect the ground
cable.
●Make sure the power switch on the charger is off when connecting and disconnecting the charger cables to the battery.
■After recharging/reconnecting the battery
●The engine may not start. Follow the pr ocedure below to initialize the system.
Shift the shift lever to P.
Open and close any of the doors.
Restart the engine.
●Unlocking the doors using the smart entry & start system may not be possible immedi-
ately after reconnecting the battery. If this happens, use the wireless remote control or the mechanical key to lock/unlock the doors.
●Start the engine with the engine switch in ACCESSORY mode. The engine may not
start with the engine switch turned off. However, the engine will operate normally from the second attempt.
●The engine switch mode is recorded by the vehicle. If the battery is disconnected and
reconnected, the vehicle will return the engi ne switch mode to the status it was in before the battery was disconnected. Make sure to turn off the engine switch beforedisconnecting the battery. Take extra care when connecting the battery if the engine
switch mode prior to the battery being disconnected is unknown.
If the system will not start even after multip le attempts at all the methods above, contact any authorized Lexus dealer or repairer, or another duly qualified and equipped profes-
sional.
1
2
3

6517-3. Do-it-yourself maintenance
7
Maintenance and care
RX350/RX200t_EE_OM48F32E
■Back-up lights
Open the back door and remove
the cover.
Using a flathead sc rewdriver, remove the cover.
To prevent scratching to the vehicle,
wrap the tip of the flathead screw- driver with a cloth, etc.
Turn the bulb base
counterclockwise and remove it.
Remove the light bulb.
Install a new light bulb and then
install the bulb base to the light
unit by inserting it and turning it
clockwise.
After installing the bulb base, wiggle
it lightly to make sure it is securely installed and turn on the back-uplights to visually check that there is no
light leaking from between the bulb base and light unit.
1
2
3
4

6768-2. Steps to take in an emergency
RX350/RX200t_EE_OM48F32E
Take the appropriate actions as instructed in the message displayed.
If any of the following messages are displayed, also refer to this Owner’s Manual.
■If “Shift to P Before Exiting Vehicle” is shown
Message is displayed when the driver’s door is opened without turning the
engine switch off with the shift lever in any position other than P.
Shift the shift lever to P.
■If “Power Turned Off to Save Battery” is displayed
This message is displayed when the po wer was cut off due to the automatic
power off function.
The next time the engine is started, increase the engine speed slightly and
maintain it at that speed for approximately 5 minutes to recharge the battery.
■If “AWD System Overheated Switch ing to 2WD Mode” or “AWD System
Overheated 2WD Mode Engaged” is displayed (AWD models)
This message may be displayed when dr iving under extremely high load con-
ditions.
Drive the vehicle at low speeds or stop the vehicle in a safe place with the
engine running until the message is cleared.
If the message is not cleared, have the vehicle inspected by any authorized
Lexus dealer or repairer, or another duly qualified and equipped professional.
■If “A New Key has been Registered Cont act Your Dealer for Details” is dis-
played
This message will be displayed each time the driver’s door is opened when the
doors are unlocked from the outside for approximately one week after a new
electronic key has been registered.
If this message is displayed but you have not had a new electronic key regis-
tered, ask any authorized Lexus dealer or repairer, or another duly qualified
and equipped professional. to check if an unknown electronic key (other than
those in your possession) has been registered.
Other messages displayed on the multi-information display

7108-2. Steps to take in an emergency
RX350/RX200t_EE_OM48F32E
■Unlocking the door
Use the mechanical key ( P. 135) in order to perform the following opera-
tions:
Insert the mechanical key while
pulling on the driver’s door han-
dle.
Unlocking the door.
Remove the key, return the handle, and then pull the handle again.
If the electronic key does not operate properly
If communication between the electronic key and vehicle is interrupted
( P. 170) or the electronic key cannot be used because the battery is
depleted, the smart entry & start system and wireless remote control cannot
be used. In such cases, the doors can be opened and the engine can be
started by following the procedure below.
Locking and unlocking the doors
1
2
3

7118-2. Steps to take in an emergency
8
When trouble arises
RX350/RX200t_EE_OM48F32E
■Locking the door
With the door open, push down
the inside lock button.
For the front doors
Close the door while pulling the door handle.
For the rear doors
Close the door.
■Key linked functions
*: If equipped
1
Closes the windows and the moon roof* or panoramic moon roof* (turn and hold)
Opens the windows and the moon roof* or panoramic moon roof* (turn and hold)
These settings must be customized at any
authorized Lexus dealer or repairer, or another duly qualified and equipped professional.
2
2
1
2

7138-2. Steps to take in an emergency
8
When trouble arises
RX350/RX200t_EE_OM48F32E
■Stopping the engine
Shift the shift lever to P, set the parking brake, and press the engine switch as you nor- mally do when stopping the engine.
■Replacing the key battery
As the above procedure is a temporary measur e, it is recommended that the electronic key battery be replaced immediately when the battery is depleted. ( P. 638)
■Alarm (if equipped)
Using the mechanical key to lock the doors will not set the alarm system.
If a door is unlocked using the mechanical key when the alarm system is set, the alarm may be triggered. ( P. 83)
■Changing engine switch modes
Release the brake pedal and press the engine switch in step above.
The engine does not start an d modes will be changed each time the switch is pressed.
( P. 247)
■When the electronic key does not work properly
●Make sure that the smart entry & start system has not been deactivated in the
customization setting. If it is off, turn the function on. (Customizable features P. 743)
●Check if battery-saving mode is set. If it is set, cancel the function. (P. 170)
WARNING
■When using the mechanical key and operating the power windows or the moon roof
or panoramic moon roof
Operate the power window or the moon roof or panoramic moon roof after checking to make sure that there is no possibility of any passenger having any of their body parts
caught in the window or the moon roof or panoramic moon roof. Also, do not allow children to operate the me chanical key. It is possible for children and other passengers to get caught in the powe r window or the moon roof or panoramic
moon roof.
3

7148-2. Steps to take in an emergency
RX350/RX200t_EE_OM48F32E
If you have a set of jumper (or booster) cables and a second vehicle with a 12-volt
battery, you can jump start your vehicle by following the steps below.
Confirm that the electronic key is
being carried.
Vehicles with an alarm: When connect- ing the jumper (or booster) cables,depending on the situation, the alarm
may activate and doors locked. ( P. 84)
Open the hood (P. 597).
If the vehicle battery is discharged
The following procedures may be used to start the engine if the vehicle’s bat-
tery is discharged.
You can also call any authorized Lexus dealer or repairer, or another duly
qualified and equipped professional.
1
2

7168-2. Steps to take in an emergency
RX350/RX200t_EE_OM48F32E
Start the engine of the second vehicle. Increase the engine speed slightly and
maintain at that level for approximately 5 minutes to recharge the battery of
your vehicle.
Open and close any of the doors of your vehicle with the engine switch off.
Maintain the engine speed of the second vehicle and start the engine of your
vehicle by turning the engine switch to IGNITION ON mode.
Once the vehicle’s engine has started, remove the jumper cables in the exact
reverse order from which they were connected.
Once the engine starts, have the vehicle inspected at any authorized Lexus
dealer or repairer, or another duly qualified and equipped professional as soon
as possible.
■Starting the engine when the battery is discharged
The engine cannot be started by push-starting.
■To prevent battery discharge
●Turn off the headlights and the audio system while the engine is stopped. (RX200t: Except when the engine is stopped by the Stop & Start system.)
●Turn off any unnecessary electrical components when the vehicle is running at a low
speed for an extended period, such as in heavy traffic.
■Charging the battery
The electricity stored in the battery will discharge gradually even when the vehicle is not
in use, due to natural discharge and the draining effects of certain electrical appliances. If the vehicle is left for a long time, the battery may discharge, and the engine may beunable to start. (The battery recharges automatically during driving.)
■When the battery is removed or discharged
●In some cases, it may not be possible to unlock the doors using the smart entry & startsystem when the battery is discharged. Us e the wireless remote control or the mechan-
ical key to lock or unlock the doors.
●The engine may not start on the first attempt after the battery has recharged but will start normally after the second attempt. This is not a malfunction.
●The engine switch mode is memorized by the vehicle. When the battery is recon-nected, the system will return to the mode it was in before the battery was discharged. Before disconnecting the battery, turn the engine switch off.
If you are unsure what mode the engine switch was in before the battery discharged, be especially careful when reconnecting the battery.
●Vehicles with power back door: The power back door must be initialized. (P. 159)
●RX200t: After the battery terminals have been disconnected then reconnected or the battery has been replaced, the Stop & Start system may not automatically stop theengine for approximately 5 to 60 minutes.
4
5
6
7

741
9
9-2. Customization
Vehicle specifications
RX350/RX200t_EE_OM48F32E
Some function settings are changed simultaneously with other functions being
customized. Contact any authorized Lexu s dealer or repairer, or another duly
qualified and equipped professional for further details.
Settings that can be changed on the audio system screen
Settings that can be changed by any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional
Definition of symbols: O = Available, – =Not available
■Gauges, meters and multi-information display ( P. 96, 100)
*1: The default setting varies according to countries.
*2: Except F SPORT models
■Door lock (P. 140, 710)
Customizable Features
1
2
FunctionDefault settingCustomized setting
Units*1km (L/100km)km (km/L) O—miles (MPG)
Color*2Color 1Color 2O—
Suggestion functionOnOff—O
12
FunctionDefault settingCustomized setting
Unlocking using a mechanical keyAll doors unlockedin one step
Driver’s doorunlocked in onestep, all doors
unlocked in two step
—O
Speed linked door locking func-tionOnOffOO
Shift position linked door locking
functionOffOnOO
Shift position linked door unlock- ing functionOffOnOO
Driver’s door linked door unlock-ing functionOnOffOO
12

743
9
9-2. Customization
Vehicle specifications
RX350/RX200t_EE_OM48F32E
■Smart entry & start system and wireless remote control (
P. 140, 168)
■Smart entry & start system ( P. 140, 168)
■Wireless remote control ( P. 134, 140, 151)
*: If equipped
FunctionDefault settingCustomized setting
Operation signal
(Emergency flashers)OnOffOO
Time elapsed before automatic
door lock function is activated if
door is not opened after being
unlocked
30 seconds
60 seconds
—O120 seconds
Open door warning buzzerOnOff—O
12
FunctionDefault settingCustomized setting
Smart entry & start system On Off O O
Smart door unlocking All the doors Driver’s door O O
12
FunctionDefault settingCustomized setting
Wireless remote control On Off — O
Unlocking operation All doors unlocked
in one step Driver’s door
unlocked in one
step, all doors
unlocked in two
step OO
Opening/closing of the power
back door
* using the
switch of the wireless remote
control Open: Press for 1
second with the
back door
unlocked
Close: Press for 1
second Off
—O
Open: One short
press with the back
door unlocked
Close: One short
press
Open: Press twice
with the back door
unlocked
Close: Press twice
12