remote control LEXUS RX330 2006 Owner's Manual

AUDIO
310(b) Using the remote control
To use the rear seat entertainment system remote control,
direct
the signal output portion of the remote control to the
signal reception portion of the rear seat entertainment
system display.
The remote control does not operate properly when the signal
reception portion of the display is exposed to direct sunlight.
Block the display from direct sunlight.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop while driving, stow the remote control in
the console box or front seatback pocket when it is not
in use.

AUDIO
311
NOTICE
Observe the followings, otherwise the remote control
may be damaged.
Do not drop or strongly knock the remote control
against hard objects.
 Do not sit on or place heavy objects on the remote
control.
 Do not leave the remote control exposed to high
temperatures (such as on the instrument panel) for a
long time, otherwise the remote control may be
damaged.
(c) Locating the remote control
If you lose sight of the remote control, push and hold the
“CURSOR (REMOTE)” button on the DVD player unit until you
hear a beep. A buzzer sounds from the remote control to let you
know where it is.
To stop the buzzer, push any button of the remote control.
If the remote control is located close to something that blocks
the signal, such as some kind of metal, the remote control may
not receive the signal and the buzzer may not sound.

AUDIO
312
FCC InformationCaution: Any changes or modifications in
construction of this device which are not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
FCC Label Information This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, Including interference that may cause
undesired operation.Quick reference for your remote control
 With navigation system

AUDIO
316CD or DVD
mode: Use this switch to fast forward/rewind a disc
or select a desired track (“CD” mode)/chapter·track (“DVD\
”
mode).
 To select a desired track (“CD” mode) or chapter/track
(“DVD” mode), push this switch briefly.
 To fast forward or rewind a disc, push and hold this switch
until you hear a beep. To stop fast forwarding or rewinding,
push and hold the same side of the switch until you hear a
beep.
4“DISC/CH/PROG” switch: Use this switch to select a
preset station (radio mode), reverse side of a tape
(“TAPE” mode) or a desired CD (“CD” mode).
Radio mode: Push this switch to select a preset station. The
station you assigned to that particular switch on the audio
system will be selected.
“TAPE” mode: Push this switch to select the reverse side of
a cassette tape.
“CD” mode: Push this switch to select a desired CD (for a CD
changer only). Push until the desired CD number appears.
5“CURSOR (REMOTE)” switch: Use this switch to
display the DVD control switches or to locate the remote
control when you lose sight of the remote control.
6Joy stick and “ENT” switch: Use this joy stick to select
a control switch, mode switch on the screen or the menu
for a disc. Push the “ENT” switch to input the selected
switch or menu.
7“DISC” indicator light: This light indicates that the disc
is loaded.

AUDIO
319

1Remote control buttons (with navigation system)
2Remote control buttons (without navigation
system)
3DVD player unit
To turn on the system, push the “SOURCE” button.
The screen indicates which mode can be selected. Push the
“DVD” or “VIDEO” button when the connected DVD player or
your personal audio machine is on. The rear seat
entertainment system will be turned on.
The rear seat entertainment system can select all the modes.
When a cassette tape, a CD, a DVD video disc, an audio CD,
a video CD, a CD text, a dts−CD or a DVD audio disc is not
loaded on the front audio system or the DVD player, only the
radio mode can be selected on the rear seat entertainment
system.
To turn off the system, push the “OFF” button.
When the front audio system is turned off, the rear audio
system and the DVD player will be turned off simultaneously.

AUDIO
321

1Screen switch2Remote control button
3DVD player unit
Use the joy stick to select the mode. Push the “ENT”
button to enter the mode.
The mode display which is selected by the joy stick is
colored blue. When the “ENT” button is pushed, the mode
display changes to green. If the mode display is gray, it
cannot be selected.
The “Speaker sound” on the mode display is selected on the
front audio system.
When you select a mode, the screen indicates which is
selected.Radio operation
(a) Listening to the radio
 AM mode
FM mode

AUDIO
322Using joy stick and the “ENT” button to select either AM or FM
mode.
“AM”, “FM1” or “FM2” appears on the screen.
If the front audio system receives
a traffic announcement (TA)
while the rear seat audio system is in the radio mode, “TRAF”
will flash on the screen and the rear seat audio system will turn
off. When the front audio receives a traf fic announcement (TA),
the rear seat audio system cannot select the AM/FM mode. (b) Selecting a station
Tune in the desired station using one of the following methods.
1Remote control button
2DVD player unit
Seek tuning: Push and hold the “
” or “” (TUNE/TRACK)
button. The radio will seek up or down for a station of the
nearest frequency and will stop on reception. Each time you
push the button, the stations will be searched one after
another.

AUDIO
323
Manual tuning: Quickly push and release the “
” or “”
(TUNE/TRACK) button. Each time you push the button, the
radio will step up or down to another frequency. If you push and
hold the button, and the radio will go into the seek mode.
1Remote control button
2DVD player unit
To scan the preset stations: You can scan only the preset
stations for the band of the front audio system. Push the “
”
or “” (DISC/CH/PROG) button. The radio will tune in the next
preset station up or down the band. The station frequency will
appear on the screen.
Cassette tape player operation
(a) Playing a cassette tape
Using joy stick and the “ENT” button to select the cassette tape
mode.
“TAPE” appears on the display.
Autoreverse feature: After the cassette player reaches the
end of a tape, it automatically reverses and begins to play the
other side, regardless of whether the cassette was playing or
fast forwarding.

AUDIO
324(b) Manual program selection
1Remote control button
2DVD player unit
“Program” button: Push the “
” or “” (DISC/CH/PROG)
button to select the other side of a cassette tape. The screen
indicates which side is currently selected. (“
” indicates the
top side, “” indicates the bottom side.)
1Remote control button
2DVD player unit
“Rewind” button: Push the “
” (TUNE/TRACK) button to
rewind a tape. “REW” appears on the display.
To stop rewinding, push the same button.
“Fast forward” button: Push the “
” (TUNE/TRACK) button
to fast forward a cassette tape. “FF” appears on the display.
To stop fast forwarding, push the same button.

AUDIO
325
(c) Automatic program selection
1Remote control button
2DVD player unit
“Automatic program selection” button: The automatic
program selection feature allows you to program your cassette
player to skip forward or backward to locate the song you want
to hear. You can skip up to 9 programs at a time.
Push the “
” (TUNE/TRACK) button to skip forward. “FF” and
the number will appear on the display. Push the button until the
number you want to skip appears on the display. After that, the
player will automatically skip forward.
When the end of the tape is reached, the player automatically
reverses sides and resumes normal play. Push
the “
” (TUNE/TRACK) button to skip backward. Push
the button until “REW” and the number you want to skip appear
on the display.
 If you set “REW 1”, the player will rewind to the beginning
of the current program.
 When counting the number of programs you want to rewind,
remember to count the current program as well. For
example, if you want to rewind to a song that is two before
the song you are listening to, push this button until “REW
3” appears on the display.
When the beginning of the tape is reached, the player
automatically resumes normal play.
There must be at least 3 seconds of blank space between
programs for this feature to work correctly.
This feature may not work well with some spoken word, live or
classical recordings.