sensor LEXUS SC300 1991 Service Owners Manual

How To Proceed With Troubleshooting
Malfunction symptoms of the airbag system are difficult to confirm, so the diagnostic codes become the most
important source of information when troubleshooting. Perform troubleshooting of the airbag system in ac\
cor-
dance with the following procedure:
HINT: Do not disconnect the battery negative (±) terminal cable until st\
ep [ 3 ], Diagnostic Code Check and Re-
cording, has been completed.1. CUSTOMER PROBLEM ANALYSIS Using the CUSTOMER PROBLEM ANALYSIS CHECK SHEET (See page AB±29) for reference, ask the
customer in as much detail as possible about the problem.
2. WARNING LIGHT CHECK Check the airbag warning light. If the light remains on, a malfunction is sto\
red in the center airbag sensor,
assembly, so proceed to step [ 3 ]. If the airbag warning light is not on, a malf\
unction has occurred in the
airbag warning light circuit, so perform troubleshooting for code 22.
HINT: Code 22 is recorded when a malfunction occurs in the airbag warning li\
ght system.
If an open malfunction occurs in the airbag warning light system, the airb\
ag warning light does not light up,
so that until the malfunction is repaired, the diagnostic codes (includin\
g code 22) cannot be confirmed.
3. DIAGNOSTIC CODE CHECK AND RECORDING Check the diagnostic codes and make a note of any malfunction codes which are\
output. If a normal code
is output, an abnormality in the power source circuit may have occurred, so perform troubleshootin\
g for
source voltage in step [ 8 ].
If code 22 is output, skip steps [ 4 ] and [ 5 ] and proceed to step [ 7\
].
4. CLEARING OF MALFUNCTION CODE (EXCEPT CODE 41) Clear the malfunction code.
HINT: The malfunction code output in step [ 3 ] indicates that a malfunction \
has occurred in the circuit desig-
nated by the malfunction code, but does not indicate whether the malfunction \
is still occurring or whether
it was in the past.
Accordingly, it is necessary to find out the present condition of the malfunction oc\
currence by clearing the
malfunction code and performing the diagnostic code check again. If this\
operation is neglected and trou-
bleshooting is performed using only the malfunction code confirmed in step [ 3 ], isola\
ting the problem com-
ponent becomes difficult and invites mistaken diagnosis.
5. DIAGNOSTIC CODE CHECK AND RECORDING [ 6 ] SYMPTOM SIMULATION After repeating ignition switch ON±OFF operation (ON: wait 20 secs., OFF: wait 20 secs.) 5 times, check
the diagnostic codes. If any code other than code 41 is output, the malfunc\
tion is still occurring, so proceed
to step [ 7 ].
If code 41 only is output, the following three cases are possible:
w Intermittent trouble occurred previously, but it is now normal.
w The problem has been corrected, but clearing of code 41 has been forgott\
en.
w There is a malfunction in the circuit for code 41.
Focusing on the circuit of the malfunction code stored in step 3, use th\
e simulation method in step [ 6 ]
in order to simulate the malfunction. If the malfunction occurs, proceed t\
o step [ 7 ]; if not, proceed to step.
[ 12 ]. AB±25
SRS AIRBAG
± Troubleshooting
WhereEverybodyKnowsYourName

NOTICE: When connecting the battery after clearing the malfunction code, always\
do it with the igni-
tion switch in LOCK position. When the battery has been reconnected, turn the ignition switch to
ACC or ON position after at least 2 seconds have elapsed.
If the battery is reconnected with the ignition switch in ACC or ON posi\
tion, or the ignition switch
is turned to ACC or ON within 2 seconds of connecting the battery, it is possible that the diagnosis
system will not operate normally.
HINT: Determine the malfunction in the airbag system in step [ 6 ] by whethe\
r or not a malfunction code
other than code 41 is output.
7. DIAGNOSTIC CODE CHART Proceed to the appropriate flow chart in step [ 8 ] in accordance with the malfunction code found in step
[ 5 ] or [ 6 ].
8. CIRCUIT INSPECTION [ 9 ] REPAIR Find out if the problem lies in a sensor, actuator or wire harness and connector, and repair the problem.
After the problem part is repaired, reinstall the disassembled parts. Do not \
start work until at least 20 se-
conds after the ignition switch is turned to the LOCK position and the negati\
ve (±) terminal cable is discon-
nected.
CAUTION: If incorrect procedure is used, a malfunction may occur in the system o\
r there is the dan-
ger that airbag may be accidentally activated during the repair operation. Carefully read the GEN-
ERAL DESCRIPTION (See page AB±2) and the cautions for each operation, and perform repairs in
the correct order using the correct methods.
HINT: The following illustration for the CIRCUIT INSPECTION shows each conne\
ctor for the circuit from
the center airbag sensor assembly to the steering wheel pad (squib).
10 CLEARING OF MALFUNCTION CODE (EXCEPT CODE 41) When all the malfunction codes found in steps [ 5 ] and [ 6 ] have been repa\
ired, clear the malfunction
codes.
AB±26
SRS AIRBAG
± Troubleshooting
WhereEverybodyKnowsYourName

Diagnosis Inspection
AIRBAG WARNING LIGHT CHECK
(a) Turn the ignition switch to ACC or ON and check that theairbag warning light lights up.
(b) Check that the airbag warning light goes out after approx. 6 seconds.
HINT:
wWhen the ignition switch is at ACC or ON and the airbag
warning light remains on, the center airbag sensor
assembly has detected a malfunction code.
wIf, after approx. 6 seconds have elapsed, the airbag
warning light sometimes lights up or the airbag warning
light lights up even when the ignition switch is OFF, a
short in the airbag warning light circuit can be
considered likely. Proceed to Airbag warning light
system (always lit up) on page AB±84.
DIAGNOSTIC CODE CHECK
1. OUTPUT DIAGNOSTIC CODE
(a) Turn the ignition switch to ACC or ON position and waitapprox. 20 seconds.
(b) Using SST, connect terminals Tc and E
1 of the TDCL.
SST 09843±18020
NOTICE: Never make a mistake with the terminal connec-
tion position as this will cause a malfunction.
2. READ DIAGNOSTIC CODE Read the diagnostic code as indicated by the number of
times the airbag warning light blinks.
wNormal code indication
The light will blink 2 times per second.
wMalfunction code indication
In the event of a malfunction, the light will blink. The first
number of the code No. will equal the first digit of a
2±digit diagnostic code, and after a 1.5 second pause,
the 2nd number of the code No. will equal the 2nd digit.
If there are two or more codes, there will be a 2.5 second
pause between each.
After all the codes have been output, there will be a 4.0 se-
cond pause and they will all be repeated.
HINT:
wIn the event of a number of trouble codes, indication will
begin from the smaller numbered code to the larger.
wIf a diagnostic code is not output or is continuously
output, proceed to the TC terminal circuit inspection on
page AB±86 .
AB±30
SRS AIRBAG
± Troubleshooting
WhereEverybodyKnowsYourName

DIAGNOSTIC CODES
CodeNo.Blink PatternDiagnosisTrouble AreaAIRBAG
Warning Light
(Nor

System normal±OFF
(Nor-
mal)
Source Voltage drop
Battery

Center airbag sensor assemblyON
11

Short in squib circuit
(to ground)

Front airbag sensor
malfunction

Flower sensor malfunction
Steering wheel pad (squib)

Front airbag sensor

Spiral cable

Center airbag sensor assembly

Wire harness
ON
12

Short in squib circuit
(to +B)
Steering wheel pad (squib)

Front airbag sensor

Spiral cable

Center airbag sensor assembly

Wire harness
ON
13

Short in squib circuit
(between D+ wire harness
and D± wire harness)

Steering wheel pad (squib)

Spiral cable

Center airbag sensor assembly

Wire harness
ON
14

Open in squib circuit
Steering wheel pad (squib)

Spiral cable

Center airbag sensor assembly

Wire harness
ON
15

Open in front airbag
sensor circuit
Front airbag sensor

Center airbag sensor assembly

Wire harness
ON
22

Airbag warning light
system malfunction
Airbag warning light

Center airbag sensor assembly

Wire harness
ON
31

Center airbag sensor
assembly malfunction

Center airbag sensor assemblyON
41

Malfunction stored in
memory

(Center airbag sensor assembly)ON
HINT:
w When the airbag warning light remains lit up and the diagnostic code in the n\
ormal code, this means a
source voltage drop.
This malfunction is not stored in memory by the center airbag sensor ass\
embly and if the power source
voltage returns to normal, after approx. 10 seconds the airbag warning l\
ight will automatically go out.
w Code 22 in recorded when a malfunction occurs in the airbag warning light sy\
stem. If an open malfunction
occurs in the airbag warning light system, the airbag warning light does not l\
ight up, so that until the
mal±function is repaired, the diagnostic codes (including code 22) cannot be confi\
rmed.
w When a malfunction occurs in the airbag system, malfunction codes 11 to 31 are output. After repairing
the malfunction indicated by malfunction codes 11 to 31, codes 11 to 31 are cleared from the memory, but
code 41 is output instead. Once the malfunction has been detected, the airba\
g warning light will remain
lit up until code 41 is cleared, even though the malfunction has been re\
paired.
w When 2 or more codes are indicated, the lowest numbered code will appear\
first.
w If a code not listed on the chart is displayed, then the center airbag s\
ensor assembly is faulty. AB±31
SRS AIRBAG
± Troubleshooting
WhereEverybodyKnowsYourName

Wiring Diagram
CENTER AIRBAG SENSOR ASSEMBLY CONNECTOR
No.SymbolTerminal NameNo.SymbolTerminal Name
18E2Ground
2±SRRH Front Airbag Sensor (±)9LAAirbag Warning Light
3+SRRH Front Airbag Sensor (+)10D±Squib (±)
4+SLLH Front Airbag Sensor (+)11D+Squib (+)
5±SLLH Front Airbag Sensor (±)12TcDiagnosis
6+BBattery (ECU±B Fuse)13E1Ground
7IG2Power Source (IGN Fuse)14AccPower Source (CIG Fuse)
AL1Electrical Connection Check
MechanismBL2Electrical Connection Check
Mechanism
AB±33SRS AIRBAG ± Troubleshooting
WhereEverybodyKnowsYourName

Diagnostic Code Matrix Chart
If a malfunction code is displayed during the diagnostic code check, check\
the circuit listed for that code in the
table below (Proceed to the page given for that circuit).
Code No.DiagnosisPage
(Normal)*1Source voltage dropAB±40
11Short in squib circuit or front airbag sensor circuit (to ground)AB±42
12Short in squib circuit or front airbag sensor circuit (to +B)AB±48
13Short in squib circuit (between D+ wire harness and D± wire harness)\
AB±54
14Open in squib circuitAB±62
15Open in front airbag sensor circuitAB±68
22*2Airbag warning light system malfunctionAB±74
31Center airbag sensor assembly malfunctionAB±80
41*3Malfunction stored in memoryAB±82
HINT:
*1 When the airbag warning light remains lit up and the diagnostic code is the normal code, this means asource voltage drop.
*2 Code 22 is recorded when a malfunction occurs in the airbag warning light sy\
stem. If an open malfunction occurs in the airbag warning light system, the airbag warning light does not light up, so that until the mal-
function is repaired, the diagnostic code (including code 22) cannot be confir\
med.
*3 When a malfunction occurs in the airbag system, malfunction codes 11 to 31 are output. After repairing the malfunction indicated by malfunction codes 11 to 31, codes 11 to 31 are cleared from the memory, but
code 41 is output instead. Once the malfunction has been detected, the airba\
g warning light will remain
lit up until code 41 is cleared, even though the malfunction has been re\
paired.
Problem Symptom Chart
Proceed with troubleshooting of each circuit in the table below.
Problem SymptomInspection ItemPage

With the ignition switch at ACC or ON, the airbag warning light
sometimes lights up after approx. 6 seconds have elapsed.

Airbag warning light lights up even when ignition switch is in the
LOCK position.
Airbag warning light system
(Always lit up)AB±84

Diagnostic code not displayed.

Diagnostic code continuously displayed.
Tc terminal circuitAB±86
AB±34SRS AIRBAG ± Troubleshooting
WhereEverybodyKnowsYourName

Circuit Inspection
Diag. Code (Normal)Source Voltage Drop
CIRCUIT DESCRIPTION
The airbag system is equipped with a voltage±increase circuit (DC±DC\
converter) in the center airbag
sensor assembly in case the source voltage drops.
When the battery voltage drops, the voltage±increase circuit (DC±DC c\
onverter) functions to increase
the voltage of the airbag system to normal voltage.
The diagnosis system malfunction display for this circuit is different to other circuits±when the airbag
warning light remains lit up and the diagnostic code is a normal code, source voltage d\
rop is indicated.
Malfunction in this circuit is not recorded in the center airbag sensor assembly, and approx. 10 se-
conds after the source voltage returns to normal, the airbag warning lig\
ht automatically goes off.
Code No.
Diagnosis
(Normal)Source voltage drop.
DIAGNOSTIC CHART
Preparation.
Does airbag warning light turn on after
approx. 10 seconds?
Check battery and charging system
(See page CH±1). Check diagnostic code, and if a
malfunction code is output,
perform troubleshooting according
to malfunction code.
If a normal code is output,
replace center airbag sensor
assembly.
WIRING DIAGRAM
AB±40SRS AIRBAG
± Troubleshooting
WhereEverybodyKnowsYourName

(1) Turn ignition switch LOCK.
(2) Disconnect center airbag sensor assemblyconnector.
(3) Turn ignition switch ON. But do not start engine.
(4) Measure voltage at IG
2 or ACC on connector
wire harness side of center airbag assembly and
operate electric system (defogger, wiper,
headlight, heater, blower, etc.).
Voltage: 6 V ± 11.5 V at IG
2 and ACC.
(5) Turn electric system switch OFF.
(6) Turn ignition switch LOCK.
(7) Remove voltmeter and connect center airbag sensor assembly.
Does airbag warning light turn off after approx. 10 seconds?
Preparation.
Turn ignition switch ON.
Operate electric system checked in [ 1 ] (4) and
check that airbag warning light goes off after
approx. 10 seconds.
Check diagnostic code, and if a malfunction
code is output, perform troubleshooting
according to malfunction code. If a normal
code is output, replace center airbag
sensor assembly.
Check battery and charging system
(See page CH±1)
INSPECTION PROCEDURE
AB±41SRS AIRBAG ± Troubleshooting
WhereEverybodyKnowsYourName

Diag. Code 11Short is Squib Circuit or Front Airbag
Sensor Circuit (to Ground)
CIRCUIT DESCRIPTION
The squib circuit consists of the center airbag sensor assembly, spiral cable and the steering wheel
pad (squib). It causes the airbag to deploy when the airbag deployment\
conditions are satisfied.
The front airbag sensor detects the deceleration force in a frontal collision and is located in \
the front
fender on the left and right sides.
For details of the function of each component, see FUNCTION OF COMPONENTS on page AB±5.
Diagnostic code 11 is recorded when occurrence of ground short is detected in the squib circui\
t or front
airbag sensor circuit.
Code No.
Diagnosis
11

Short circuit in squib wire harness (to ground).

Squib malfunction.

Short circuit in front airbag sensor +S wire harness (to ground).

Front airbag sensor malfunction.

Short circuit between +S wire harness and ±S wire harness of front ai\
rbag sensor.

Spiral cable malfunction.

Center airbag sensor assembly malfunction.
DIAGNOSTIC CHART
Preparation.
Check front airbag sensor circuit.
(Measure resistance between terminals +SR
and ±SR, +SL and ±SL of center airbag
sensor assembly connector.
Check front airbag sensor circuit.
(Measure resistance between terminals +SR,
+SL of center airbag sensor assembly
connector and body ground.
Check squib circuit.
Check center airbag sensor assembly.
Check squib.
From the results of the above inspection, the
malfunctioning part can now be considered
normal. To make sure of this, use the
simulation method to check. Go to step [ 7 ] on next page.
Repair or replace harness or
connector between center airbag
sensor assembly and front airbag
sensor (See page
AB±20).
Go to step [ 8 ] on next page.
Replace center airbag sensor
assembly.
Replace steering wheel pad.
AB±42SRS AIRBAG ± Troubleshooting
WhereEverybodyKnowsYourName

DIAGNOSTIC CHART (Cont'd)
Check front airbag sensor.Replace front airbag sensor.
Repair or replace spiral cable.Check spiral cable. Repair or replace harness or connector
between center airbag sensor assembly and
front airbag sensor (See page AB±20).
Repair or replace harness or connector
between center airbag sensor assembly and
spiral cable.
WIRING DIAGRAM
AB±43SRS AIRBAG ± Troubleshooting
WhereEverybodyKnowsYourName