fuse LEXUS SC300 1991 Service User Guide

OKNG
1
2
3
4
5
6
6
OK
OK
YES
YES NG
NG NO
NO
Check connection of center airbag sensor
assembly connector.
Preparation.
Check airbag warning light circuit.
Does airbag warning light come on?
Is new ECU ±B fuse burnt out again? GO to step
Repair.
Repair airbag warning light circuit
(See page BE±150).
Check terminal LA of center
airbag sensor assembly and
electrical connection check
mechanism. If normal, replace
center airbag sensor assembly.
Using simulation method,
reproduce malfunction symptoms
(See page IN±20).
Check harness between ECU ±B fuse and
airbag warning light, and ECU±B fuse and
center airbag sensor assembly. From the results of the above inspection,
the malfunctioning part can now be
considered normal. To make sure of this,
use the simulation method to check.
Check ECU ±B fuse.
DIAGNOSTIC CHART
Troubleshooting for this system is different for when the airbag warning light does not light up and for
when diagnostic code 22 is output. Confirm the problem symptoms first before\
selecting the appropriate
troubleshooting procedure.
HINT: If airbag warning light does not light up, perform the following troub\
leshooting:
±
SRS AIRBAG TroubleshootingAB±75
WhereEverybodyKnowsYourName

Check ECU±B fuse.
NG
OK
1
6Go to step
(1) Disconnect battery negative (±) terminal cable, and wait at least 20 seconds.
(2) Remove steering wheel pad (See page AB±14).
When storing steering wheel pad, keep upper
surface of pad facing upward.
NG
OKRepair.
Check connection of center airbag sensor assembly connector.2
3Preparation.
INSPECTION PROCEDURE
HINT: If airbag warning light does not light up, perform the following troubl\
eshooting:
±
SRS AIRBAG TroubleshootingAB±77
WhereEverybodyKnowsYourName

4
5
6
Check terminal LA of center airbag sensor assem-
bly and electrical connection check mechanism.
If normal, replace center airbag sensor assembly.
NG
OK
(1) Disconnect negative (±) terminal cable from battery.
(2) Connect center airbag sensor assembly.
(3) Connect negative (±) terminal cable to battery.
(4) Turn ignition switch ACC or ON. Voltage: 10±14 V
Check operation of airbag warning light.
(1) Disconnect center airbag sensor assembly.
(2) Connect negative (±) terminal cable to battery.
(3) Turn ignition switch ACC or ON.
Measure voltage LA terminal of harness side
connector of center airbag sensor assembly.
Repair airbag warning light circuit
(see page BE±150).
NG
Using simulation method, reproduce
malfunction symptoms (See page In±20).NG
OK
Check airbag warning light circuit.
Does airbag warning light come on?
Is new ECU±B fuse burnt out again?
From the results of the above inspection, the malfunctioning part can now be considered norm\
al. To
make sure of this, use the simulation method to check.
Check harness between ECU±B fuse and airbag warning light, and ECU±B fus\
e and center airbag sensor
assembly.
AB±78±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName

OK
Check operation of airbag warning light.
NG1
WIRING DIAGRAM
2Is diagnostic code 41 output again? System is normal.
Check harness between ECU±B
fuse and center airbag sensor as-
sembly. If normal, replace center
airbag sensor assembly.
Perform troubleshooting according to
malfunction code output. NO
YES
Diag. Code 41Malfunction Stored in Memory
CIRCUIT DESCRIPTION
If a malfunction occurs in the airbag system, malfunction codes 11 to 31 may be output, and when the
battery is disconnected after the malfunction is repaired, malfunction codes 11 to 31 will be cleared,
but code 41 will be output instead.
So long as the cancellation operation for a malfunction stored in memory (\
See page
AB±32) is not per-
formed, code 41 is stored in the center airbag sensor assembly and the airbag w\
arning light remains
lit up.
Code No.Diagnosis
41
Malfunction recorded in memory.41
Center airbag sensor assembly malfunction.
DIAGNOSTIC CHART
AB±82±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName

Clear malfunction code 41 stored in memory
(See page AB±32).
Check operation of airbag warning light.
NG
OK
1
Airbag warning light turns off.
(1) Turn ignition switch LOCK, and wait at least
2 seconds.
(2) Turn ignition switch ACC or ON, and wait at least 20 seconds.
(3) Check operation of airbag warning light.
System is normal.
2Is diagnostic code 41 output again?
(1) Turn ignition switch ACC or ON, and wait at least 20 seconds.
(2) Using SST, connect terminals Tc and E
1 of TDCL.
SST 09843±18020
(3) Check diagnostic code.
Check harness between ECU±B fuse and center
airbag sensor assembly. If normal, replace
center airbag sensor assembly.
Perform troubleshooting according to malfunction code output.
NG
OK
INSPECTION PROCEDURE
±
SRS AIRBAG TroubleshootingAB±83
WhereEverybodyKnowsYourName

CLEARING OF DIAGNOSTIC CODE
1. CLEARING OF MALFUNCTION CODE(EXCEPT CODE 41)
Remove the battery negative (±) terminal or ECU±B fuse for
10 seconds or more with the ignition switch OFF.
NOTICE: When connecting the battery after cancelling
the malfunction code, always do it with the ignition
switch in LOCK position. If the battery is connected with
the ignition switch in ACC or ON position, there are cases
when the diagnosis system does not operate normally.
HINT:
wCode 41 cannot be cleared by this method.
wThe lower the temperature, the longer the battery
negative (±) terminal must be left off.
wOther memory systems (clock, audio system) will also
be cancelled out (See page AB±2).
2. CLEARING OF MALFUNCTION CODE 41 STORED IN MEMORY
(a) Connect service wires to terminals Tc and AB of theTDCL.
(b) Turn the ignition switch ACC or ON and wait approx. 6 seconds.
(c) S ta rtin g with th e Tc te rmin a l, ap p ly bo d y gr ound
alternately to terminal Tc and terminal AB twice each in
cycles of 1.0 ± 0.5 seconds. Finally, keep applying body
ground to terminal Tc.
HINT: When alternating between body ground of terminals Tc
and AB release one from body ground while applying it to the
other terminal. The time interval in between must be within
the following conditions. If it is out of the conditions, code 41
will not be cleared.
(d) After several seconds, when the airbag warning light
starts to blink in a 64 msec. cycle, cancellation is
completed.
HINT: This method clears not only code No. 41, but also other
malfunction codes all at once.
Except when instructed by the troubleshooting procedure,
use this method only when the repair procedure is completed
(See page AB±25).
AB±32
SRS AIRBAG
± Troubleshooting
WhereEverybodyKnowsYourName

Wiring Diagram
CENTER AIRBAG SENSOR ASSEMBLY CONNECTOR
No.SymbolTerminal NameNo.SymbolTerminal Name
18E2Ground
2±SRRH Front Airbag Sensor (±)9LAAirbag Warning Light
3+SRRH Front Airbag Sensor (+)10D±Squib (±)
4+SLLH Front Airbag Sensor (+)11D+Squib (+)
5±SLLH Front Airbag Sensor (±)12TcDiagnosis
6+BBattery (ECU±B Fuse)13E1Ground
7IG2Power Source (IGN Fuse)14AccPower Source (CIG Fuse)
AL1Electrical Connection Check
MechanismBL2Electrical Connection Check
Mechanism
AB±33SRS AIRBAG ± Troubleshooting
WhereEverybodyKnowsYourName

4. Read the diagnostic trouble code indicated by thenumber of times the O/D OFF indicator light blinks.
HINT: If the system is operating normally, the light will blink
2 times per second.
The malfunction code is indicated as shown in the illustration
at left (Diagnostic trouble code ª42º is shown as an example).
HINT: When 2 or more trouble codes are stored in memory,
the lower±numbered code is displayed first.
If no diagnostic trouble code is output, or if a diagnostic
trouble code is output even though no diagnostic trouble
code output operation is performed, check the TE1 terminal
circuit on page AT±118.
DIAGNOSTIC TROUBLE CODE CHECK
BY USING LEXUS HAND±HELD TESTER
AT0RD±01
1. Hook up the LEXUS hand±held tester to the DLC2.
2. Read the diagnostic trouble codes by following theprompts on the tester screen.
Please refer to the LEXUS hand±held tester operator's
manual for further details.
CANCELING DIAGNOSTIC TROUBLE
CODE
AT09T±07
After repair of the trouble area, the diagnostic trouble code
retained in the ECM memory must be canceled out by remov-
ing the EFI fuse for 10 seconds or more, with the ignition
switch off.
Check that the normal code is output after connecting the
fuse.
AT±38
±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION TROUBLESHOOTING
WhereEverybodyKnowsYourName

Troubleshooting
You will find the cause of trouble more easily by properly using the table \
shown below. In this table, the
numbers indicate the order of priority of the causes of trouble. Check each part in \
the order shown. If neces-
sary, replace the part.
See page
BE±4 ,21BE±4,21BE±4,20BE±4,20BE±156BE±152BE±149BE±151BE±152BE±26BE±392BE±4,20 ±±
Part
name
Trouble
AM1 FuseDOME FuseDOOR FusePOWER FuseTheft Deterrent and Door Lock Control ECUPower Window Main RelayPower Window Master SwitchPower Window SwitchPower Window MotorIgnition SwitchDoor Open Detection SwitchECU±IG FuseWire Harness
*1 Power window does not operate.1234
*2 Power window does not operate.35467218
ªOne Touch Power Window Systemº does
not operate.1
Only one window glass does not move.1234
ªWindow Lock Systemº does not operate1
ªWindow Lock Illuminationº does not light
up.1
Key±off power window does not operate124536
*1: Dook Lock does not operate.
*2: Dook Lock is normal.
±
BODY ELECTRICAL SYSTEM Power Window Control SystemBE±157
WhereEverybodyKnowsYourName

LIQUID CRYSTAL INNER MIRROR
SYSTEM
Description
The liquid crystal inner mirror replaces the previous mirror, which mechanically switched between the ªDayº and
ªNightº settings, with liquid crystal inside the mirror which changes the bright\
ness of the mirror surface. The com-
ponent parts of this system and their functions are shown in the table below.
Parts NameFunction
Liquid Crystal Inner
MirrorReceives current from the fuse DOME and changes the surface brightness o\
f the mirror
when switch is operated.
Key Unlock Warning
SwitchOpens the circuit so that the mirror can be operated only when the ignit\
ion key is set.
Parts Location
BE±164±
BODY ELECTRICAL SYSTEM Liquid Crystal Inner Mirror System
WhereEverybodyKnowsYourName