tdcl LEXUS SC300 1991 Service User Guide

YES
Does airbag warning light turn off?
NO
1
Replace center airbag sensor assembly. Check airbag warning light circuit
or terminal AB circuit of TDCL or
check connector.
WIRING DIAGRAM
Airbag Warning Light System (Always Lit Up)
CIRCUIT DESCRIPTION
The airbag warning light is located on the combination meter.
When the airbag system is normal, the airbag warning light lights up for\
approx. 6 seconds after the
ignition switch is turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the airbag system, the airbag warning light\
lights up to inform the driver of
the abnormality.
When terminals Tc and E of the TDCL are connected, the diagnostic code is displayed by t\
he blinking
of the airbag warning light.
DIAGNOSTIC CHART
AB±84±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName

1
(1) Turn ignition switch LOCK.
(2) Disconnect negative (±) terminal cable frombattery.
(3) Disconnect center airbag sensor assembly connector.
(4) Connect negative (±) terminal cable to battery.
Does airbag warning light turn off?
Check airbag warning light circuit or terminal
AB circuit of TDCL or check connector.NG
YES
Check operation of airbag warning light.
Replace center airbag sensor assembly.
INSPECTION PROCEDURE
±
SRS AIRBAG TroubleshootingAB±85
WhereEverybodyKnowsYourName

NG
Check voltage between terminals Tc and E
1of TDCL or check connector.
OK1
2
3
1
NG
NG
NG OK
OK
OK
3
Check voltage between terminal Tc of TDCL
or check connector and body ground.Check center airbag sensor assembly.
Replace center airbag sensor assemly.
Check resistance between terminal Tc of
center airbag sensor assembly and body
ground.
HINT: If the diagnostic code is continuously displayed, perform the following \
troubleshooting:
Repair or replace harnes or connector. Replace center airbag sensor
assembly.
Check harness between center
airbag sensor assembly and
TDCL or check connector.
Check harness between terminal
E1 of TDCL or check connector
and body ground.
Go to step
Tc Terminal Circuit
CIRCUIT DESCRIPTION
By connecting terminals Tc and E of the TDCL or check connector, the center airbag sensor assembly
is set in the diagnostic code output mode. The diagnostic codes are disp\
layed by the blinking of the
airbag warning light.
DIAGNOSTIC CHART
Troubleshooting
for this system is dif ferent depending on whether the diagnostic code is not displayed
or is continuously displayed. Confirm the problem symptoms first before se\
lecting the appropriate
troubleshooting procedure.
HINT: If the diagnostic code is not displayed, perform the following trouble\
shooting:
AB±86
±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName

INSPECTION PROCEDURE
HINT: If the diagnostic code is not displayed, perform the following troubles\
hooting:
Check voltage between terminals Tc and E1 of TDCL or check connector.
nector
Turn ignition switch ACC or ON. Measure voltage between terminals Tc and E
1 of
TDCL or check connector.
Voltage: 10 ± 14 V
Measure voltage between terminal Tc of TDCL or
check connector and body ground.Voltage: 10 ± 14 V
Check harness between terminal E1 of TDCL
or check connector and body ground
Check voltage between terminals Tc or TDCL or check connector and
body ground.
AB±88±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName

NGOK
Check center airbag sensor assembly.3
(1) Disconnect negative (±) terminal cable from
battery, and wait at least 20 seconds.
(2) Turn ignition switch lock.
(3) Disconnect center airbag sensor assembly
connector.
(4) Using a service wire, connector terminal Tc of center airbag sensor assembly connector to
body ground.
(5) Install the center airbag sensor assembly.
(6) Connect negative (±) terminal cable to battery.
(7) Turn ignition switch ACC or ON.
Check operation of airbag warning light.
Airbag light comes on.
Check harness between center airbag sensor
assembly and TDCL or check connector.
Replace center airbag sensor assembly.
C
P
OK
CautionNever turn ignition switch ACC or ON and
never connect negative (±) terminal to battery
before the center airbag sensor assembly is
installed.
±
SRS AIRBAG TroubleshootingAB±89
WhereEverybodyKnowsYourName

Diagnosis Inspection
AIRBAG WARNING LIGHT CHECK
(a) Turn the ignition switch to ACC or ON and check that theairbag warning light lights up.
(b) Check that the airbag warning light goes out after approx. 6 seconds.
HINT:
wWhen the ignition switch is at ACC or ON and the airbag
warning light remains on, the center airbag sensor
assembly has detected a malfunction code.
wIf, after approx. 6 seconds have elapsed, the airbag
warning light sometimes lights up or the airbag warning
light lights up even when the ignition switch is OFF, a
short in the airbag warning light circuit can be
considered likely. Proceed to Airbag warning light
system (always lit up) on page AB±84.
DIAGNOSTIC CODE CHECK
1. OUTPUT DIAGNOSTIC CODE
(a) Turn the ignition switch to ACC or ON position and waitapprox. 20 seconds.
(b) Using SST, connect terminals Tc and E
1 of the TDCL.
SST 09843±18020
NOTICE: Never make a mistake with the terminal connec-
tion position as this will cause a malfunction.
2. READ DIAGNOSTIC CODE Read the diagnostic code as indicated by the number of
times the airbag warning light blinks.
wNormal code indication
The light will blink 2 times per second.
wMalfunction code indication
In the event of a malfunction, the light will blink. The first
number of the code No. will equal the first digit of a
2±digit diagnostic code, and after a 1.5 second pause,
the 2nd number of the code No. will equal the 2nd digit.
If there are two or more codes, there will be a 2.5 second
pause between each.
After all the codes have been output, there will be a 4.0 se-
cond pause and they will all be repeated.
HINT:
wIn the event of a number of trouble codes, indication will
begin from the smaller numbered code to the larger.
wIf a diagnostic code is not output or is continuously
output, proceed to the TC terminal circuit inspection on
page AB±86 .
AB±30
SRS AIRBAG
± Troubleshooting
WhereEverybodyKnowsYourName

CLEARING OF DIAGNOSTIC CODE
1. CLEARING OF MALFUNCTION CODE(EXCEPT CODE 41)
Remove the battery negative (±) terminal or ECU±B fuse for
10 seconds or more with the ignition switch OFF.
NOTICE: When connecting the battery after cancelling
the malfunction code, always do it with the ignition
switch in LOCK position. If the battery is connected with
the ignition switch in ACC or ON position, there are cases
when the diagnosis system does not operate normally.
HINT:
wCode 41 cannot be cleared by this method.
wThe lower the temperature, the longer the battery
negative (±) terminal must be left off.
wOther memory systems (clock, audio system) will also
be cancelled out (See page AB±2).
2. CLEARING OF MALFUNCTION CODE 41 STORED IN MEMORY
(a) Connect service wires to terminals Tc and AB of theTDCL.
(b) Turn the ignition switch ACC or ON and wait approx. 6 seconds.
(c) S ta rtin g with th e Tc te rmin a l, ap p ly bo d y gr ound
alternately to terminal Tc and terminal AB twice each in
cycles of 1.0 ± 0.5 seconds. Finally, keep applying body
ground to terminal Tc.
HINT: When alternating between body ground of terminals Tc
and AB release one from body ground while applying it to the
other terminal. The time interval in between must be within
the following conditions. If it is out of the conditions, code 41
will not be cleared.
(d) After several seconds, when the airbag warning light
starts to blink in a 64 msec. cycle, cancellation is
completed.
HINT: This method clears not only code No. 41, but also other
malfunction codes all at once.
Except when instructed by the troubleshooting procedure,
use this method only when the repair procedure is completed
(See page AB±25).
AB±32
SRS AIRBAG
± Troubleshooting
WhereEverybodyKnowsYourName

(1) Connect connector to center airbag sensorassembly.
(2) Using a service wire, connect D
+, D± on spiral
cable side of connector between spiral cable
and steering wheel pad.
(3) Connect negative (±) terminal cable to battery, and wait at least 2 seconds.
Check squib circuit.
Codes other than code 11 may be output at this
time, but this is not relevant.
Measure resistance between D+, D± on spiral cable
side of connector between spiral cable and steer-
ing wheel pad and body ground.
Go to step [ 8 ].
Diagnostic code 11 is not output.
Resistance: 1 M
or higher
Replace center airbag sensor assembly.
Check center airbag sensor assembly.
(1) Turn ignition switch ACC or ON and wait at
least 20 seconds.
(2) Using SST, connect terminals Tc and E
1 of
TDCL.
SST 09843±18020
(3) Check diagnostic code. AB±45
SRS AIRBAG
± Troubleshooting
WhereEverybodyKnowsYourName

(1) Turn ignition switch LOCK.
(2) Disconnect battery negative (±) terminal cable,and wait at least 20 seconds.
(3) Connect steering wheel pad (squib) connector.
(4) Connect negative (±) terminal cable to battery, and wait at least 2 seconds.
Check squib.
Disconnect front airbag sensor connector.
Measure resistance between each terminal of
front airbag sensor.
Replace front airbag sensor.
Diagnostic code 11 is not output.
Replace steering wheel pad.
wDo not touch ohmmeter probes strongly against
terminals of front airbag sensor.
w Make sure the front airbag sensor connector is
properly connected.
From the results of the above inspection, the malfunctioning part can now be\
considered normal.
To make sure of this, use the simulation method to check.
Repair or replace harness or connector between center airbag sensor assembly a\
nd front airbag
sensor (See page AB±20).
Check front airbag sensor.
(1) Turn ignition switch ACC or ON, and wait at
least 20 seconds.
(2) Using SST, connect terminals Tc and E
1 of
TDCL.
SST 09843±18020
(3) Check diagnostic code.
Codes other than code 11 may be output at this
time, but this is not relevant.
AB±46
SRS AIRBAG
± Troubleshooting
WhereEverybodyKnowsYourName

(1) Turn ignition switch LOCK.
(2) Disconnect negative (±) terminal cable frombattery.
(3) Connect connector to center airbag sensor assembly.
(4) Using a service wire, Connect D
+ and D± on
spiral cable side of connector between spiral
cable and steering wheel pad.
(5) Connect negative (±) terminal cable to battery, and wait at least 2 seconds.
Check squib circuit.
Codes other than code 12 may be output at this
time, but this is not relevant.
Measure voltage at D+ on spiral cable side of con-
nector between spiral cable and steering wheel
pad.
Go to step [ 7 ].
Resistance: 1 V
Replace center airbag sensor assembly.
Check center airbag sensor assembly.
(1) Turn ignition switch ACC or ON and wait at least 20 seconds.
(2) Using SST, connect terminals Tc and E
1 of
TDCL.
SST 09843±18020
(3) Check diagnostic code.
Diagnostic code 12 is not output. AB±51
SRS AIRBAG
± Troubleshooting
WhereEverybodyKnowsYourName