display LEXUS SC300 1991 Service Owner's Guide
[x] Cancel search | Manufacturer: LEXUS, Model Year: 1991, Model line: SC300, Model: LEXUS SC300 1991Pages: 4087, PDF Size: 75.75 MB
Page 200 of 4087
YES
Does airbag warning light turn off?
NO
1
Replace center airbag sensor assembly. Check airbag warning light circuit
or terminal AB circuit of TDCL or
check connector.
WIRING DIAGRAM
Airbag Warning Light System (Always Lit Up)
CIRCUIT DESCRIPTION
The airbag warning light is located on the combination meter.
When the airbag system is normal, the airbag warning light lights up for\
approx. 6 seconds after the
ignition switch is turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the airbag system, the airbag warning light\
lights up to inform the driver of
the abnormality.
When terminals Tc and E of the TDCL are connected, the diagnostic code is displayed by t\
he blinking
of the airbag warning light.
DIAGNOSTIC CHART
AB±84±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName
Page 202 of 4087
NG
Check voltage between terminals Tc and E
1of TDCL or check connector.
OK1
2
3
1
NG
NG
NG OK
OK
OK
3
Check voltage between terminal Tc of TDCL
or check connector and body ground.Check center airbag sensor assembly.
Replace center airbag sensor assemly.
Check resistance between terminal Tc of
center airbag sensor assembly and body
ground.
HINT: If the diagnostic code is continuously displayed, perform the following \
troubleshooting:
Repair or replace harnes or connector. Replace center airbag sensor
assembly.
Check harness between center
airbag sensor assembly and
TDCL or check connector.
Check harness between terminal
E1 of TDCL or check connector
and body ground.
Go to step
Tc Terminal Circuit
CIRCUIT DESCRIPTION
By connecting terminals Tc and E of the TDCL or check connector, the center airbag sensor assembly
is set in the diagnostic code output mode. The diagnostic codes are disp\
layed by the blinking of the
airbag warning light.
DIAGNOSTIC CHART
Troubleshooting
for this system is dif ferent depending on whether the diagnostic code is not displayed
or is continuously displayed. Confirm the problem symptoms first before se\
lecting the appropriate
troubleshooting procedure.
HINT: If the diagnostic code is not displayed, perform the following trouble\
shooting:
AB±86
±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName
Page 204 of 4087
INSPECTION PROCEDURE
HINT: If the diagnostic code is not displayed, perform the following troubles\
hooting:
Check voltage between terminals Tc and E1 of TDCL or check connector.
nector
Turn ignition switch ACC or ON. Measure voltage between terminals Tc and E
1 of
TDCL or check connector.
Voltage: 10 ± 14 V
Measure voltage between terminal Tc of TDCL or
check connector and body ground.Voltage: 10 ± 14 V
Check harness between terminal E1 of TDCL
or check connector and body ground
Check voltage between terminals Tc or TDCL or check connector and
body ground.
AB±88±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName
Page 206 of 4087
NGOK
Check resistance between terminal Tc of center airbag sensor
assembly and body ground.1
Check resistance between terminal Tc of center
airbag sensor assembly and body ground.
Replace center airbag sensor assembly.
Resistance: 1M
or higher
(1) Turn ignition switch LOCK.
(2) Disconnect center airbag sensor assembly
connector.
Repair or replace harness or connector.
HINT: If the diagnostic code is continuously displayed, perform the followin\
g troubleshooting. AB±90
±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName
Page 241 of 4087
11. DIAGNOSTIC CODE CHECKAfter repeating ignition switch ON±OFF operation (ON: wait 20 secs., OFF: wait 20 secs.) 5 times, check
the diagnostic codes. If only code 41 is displayed, proceed to step [ 12 ]. If a code other than code 41 is
displayed, return to step [ 7 ] and troubleshoot the displayed malfuncti\
on code.
NOTICE: When connecting the battery after clearing the malfunction code,\
always do it with the ignition
switch in LOCK position. When the battery has been reconnected, turn the ignition \
switch to ACC or ON
position after at least 2 seconds have elapsed.
If the battery is reconnected with the ignition switch in ACC or ON positi\
on, or the ignition switch is turned
ACC or ON within 2 seconds of connecting the battery, it is possible that the diagnosis system will not oper-
ate normally.
12. CLEARING OF MALFUNCTION CODE 41 STORED IN MEMORY Clear malfunction code 41 stored in memory. This operation is not necessary only in case that the power
source voltage returns to normal.
13. CONFIRMATION TEST Check the warning light again and confirm that all the malfunctions have been\
repaired. If the warning light
indicates an abnormality, repeat the operation again from step [ 2 ]. If code 41 is output at st\
ep [ 3 ], skip
steps [ 4 ] and [ 5 ] and proceed to step [ 7 ]. AB±27
SRS AIRBAG
± Troubleshooting
WhereEverybodyKnowsYourName
Page 245 of 4087
DIAGNOSTIC CODES
CodeNo.Blink PatternDiagnosisTrouble AreaAIRBAG
Warning Light
(Nor
System normal±OFF
(Nor-
mal) Source Voltage dropBattery
Center airbag sensor assemblyON
11
Short in squib circuit
(to ground)
Front airbag sensor
malfunction
Flower sensor malfunctionSteering wheel pad (squib)
Front airbag sensor
Spiral cable
Center airbag sensor assembly
Wire harness
ON
12
Short in squib circuit
(to +B)Steering wheel pad (squib)
Front airbag sensor
Spiral cable
Center airbag sensor assembly
Wire harness
ON
13
Short in squib circuit
(between D+ wire harness
and D± wire harness)
Steering wheel pad (squib)
Spiral cable
Center airbag sensor assembly
Wire harness
ON
14
Open in squib circuitSteering wheel pad (squib)
Spiral cable
Center airbag sensor assembly
Wire harness
ON
15
Open in front airbag
sensor circuitFront airbag sensor
Center airbag sensor assembly
Wire harness
ON
22
Airbag warning light
system malfunctionAirbag warning light
Center airbag sensor assembly
Wire harness
ON
31
Center airbag sensor
assembly malfunction
Center airbag sensor assemblyON
41
Malfunction stored in
memory
(Center airbag sensor assembly)ON
HINT:
w When the airbag warning light remains lit up and the diagnostic code in the n\
ormal code, this means a
source voltage drop.
This malfunction is not stored in memory by the center airbag sensor ass\
embly and if the power source
voltage returns to normal, after approx. 10 seconds the airbag warning l\
ight will automatically go out.
w Code 22 in recorded when a malfunction occurs in the airbag warning light sy\
stem. If an open malfunction
occurs in the airbag warning light system, the airbag warning light does not l\
ight up, so that until the
mal±function is repaired, the diagnostic codes (including code 22) cannot be confi\
rmed.
w When a malfunction occurs in the airbag system, malfunction codes 11 to 31 are output. After repairing
the malfunction indicated by malfunction codes 11 to 31, codes 11 to 31 are cleared from the memory, but
code 41 is output instead. Once the malfunction has been detected, the airba\
g warning light will remain
lit up until code 41 is cleared, even though the malfunction has been re\
paired.
w When 2 or more codes are indicated, the lowest numbered code will appear\
first.
w If a code not listed on the chart is displayed, then the center airbag s\
ensor assembly is faulty. AB±31
SRS AIRBAG
± Troubleshooting
WhereEverybodyKnowsYourName
Page 248 of 4087
Diagnostic Code Matrix Chart
If a malfunction code is displayed during the diagnostic code check, check\
the circuit listed for that code in the
table below (Proceed to the page given for that circuit).
Code No.DiagnosisPage
(Normal)*1Source voltage dropAB±40
11Short in squib circuit or front airbag sensor circuit (to ground)AB±42
12Short in squib circuit or front airbag sensor circuit (to +B)AB±48
13Short in squib circuit (between D+ wire harness and D± wire harness)\
AB±54
14Open in squib circuitAB±62
15Open in front airbag sensor circuitAB±68
22*2Airbag warning light system malfunctionAB±74
31Center airbag sensor assembly malfunctionAB±80
41*3Malfunction stored in memoryAB±82
HINT:
*1 When the airbag warning light remains lit up and the diagnostic code is the normal code, this means asource voltage drop.
*2 Code 22 is recorded when a malfunction occurs in the airbag warning light sy\
stem. If an open malfunction occurs in the airbag warning light system, the airbag warning light does not light up, so that until the mal-
function is repaired, the diagnostic code (including code 22) cannot be confir\
med.
*3 When a malfunction occurs in the airbag system, malfunction codes 11 to 31 are output. After repairing the malfunction indicated by malfunction codes 11 to 31, codes 11 to 31 are cleared from the memory, but
code 41 is output instead. Once the malfunction has been detected, the airba\
g warning light will remain
lit up until code 41 is cleared, even though the malfunction has been re\
paired.
Problem Symptom Chart
Proceed with troubleshooting of each circuit in the table below.
Problem SymptomInspection ItemPage
With the ignition switch at ACC or ON, the airbag warning light
sometimes lights up after approx. 6 seconds have elapsed.
Airbag warning light lights up even when ignition switch is in the
LOCK position.Airbag warning light system
(Always lit up)AB±84
Diagnostic code not displayed.
Diagnostic code continuously displayed.Tc terminal circuitAB±86
AB±34SRS AIRBAG ± Troubleshooting
WhereEverybodyKnowsYourName
Page 254 of 4087
Circuit Inspection
Diag. Code (Normal)Source Voltage Drop
CIRCUIT DESCRIPTION
The airbag system is equipped with a voltage±increase circuit (DC±DC\
converter) in the center airbag
sensor assembly in case the source voltage drops.
When the battery voltage drops, the voltage±increase circuit (DC±DC c\
onverter) functions to increase
the voltage of the airbag system to normal voltage.
The diagnosis system malfunction display for this circuit is different to other circuits±when the airbag
warning light remains lit up and the diagnostic code is a normal code, source voltage d\
rop is indicated.
Malfunction in this circuit is not recorded in the center airbag sensor assembly, and approx. 10 se-
conds after the source voltage returns to normal, the airbag warning lig\
ht automatically goes off.
Code No.
Diagnosis
(Normal)Source voltage drop.
DIAGNOSTIC CHART
Preparation.
Does airbag warning light turn on after
approx. 10 seconds?
Check battery and charging system
(See page CH±1). Check diagnostic code, and if a
malfunction code is output,
perform troubleshooting according
to malfunction code.
If a normal code is output,
replace center airbag sensor
assembly.
WIRING DIAGRAM
AB±40SRS AIRBAG
± Troubleshooting
WhereEverybodyKnowsYourName
Page 279 of 4087
4. Read the diagnostic trouble code indicated by thenumber of times the O/D OFF indicator light blinks.
HINT: If the system is operating normally, the light will blink
2 times per second.
The malfunction code is indicated as shown in the illustration
at left (Diagnostic trouble code ª42º is shown as an example).
HINT: When 2 or more trouble codes are stored in memory,
the lower±numbered code is displayed first.
If no diagnostic trouble code is output, or if a diagnostic
trouble code is output even though no diagnostic trouble
code output operation is performed, check the TE1 terminal
circuit on page AT±118.
DIAGNOSTIC TROUBLE CODE CHECK
BY USING LEXUS HAND±HELD TESTER
AT0RD±01
1. Hook up the LEXUS hand±held tester to the DLC2.
2. Read the diagnostic trouble codes by following theprompts on the tester screen.
Please refer to the LEXUS hand±held tester operator's
manual for further details.
CANCELING DIAGNOSTIC TROUBLE
CODE
AT09T±07
After repair of the trouble area, the diagnostic trouble code
retained in the ECM memory must be canceled out by remov-
ing the EFI fuse for 10 seconds or more, with the ignition
switch off.
Check that the normal code is output after connecting the
fuse.
AT±38
±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION TROUBLESHOOTING
WhereEverybodyKnowsYourName
Page 301 of 4087
DIAGNOSTIC TROUBLE CODE CHART
AT0LR±04
If a malfunction code is displayed during the diagnostic trouble code chec\
k, check the circuit listed for that
code in the table below and proceed to the page given.
AT±60±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION TROUBLESHOOTING
WhereEverybodyKnowsYourName