code 32 LEXUS SC300 1991 Service Repair Manual

99
CURRENT IS APPLIED AT ALL TIMES THROUGH A STOP FUSE TO TERMINAL 2 OF THE STOP LIGHT SW.
WHEN THE IGNITION SW IS TURNED ON, CURRENT FLOWS FROM THE GAUGE FUSE TO TERMINAL 8 OF THE LIGHT FAILURE
SENSOR, AND ALSO FLOWS THROUGH THE REAR LIGHT WARNING LIGHT TO TERMINAL 4 OF THE LIGHT FAILURE SENSOR.
STOP LIGHT DISCONNECTION WARNING
WHEN THE IGNITION SW IS TURNED ON AND THE BRAKE PEDAL IS PRESSED (STOP LIGHT SW ON), IF THE STOP LIGHT CIRCUIT IS
OPEN, THE CURRENT FLOWING FROM TERMINAL 7 OF THE LIGHT FAILURE SENSOR TO TERMINALS 1, 2 CHANGES, SO THE LIGHT
FAILURE SENSOR DETECTS THE DISCONNECTION AND THE WARNING CIRCUIT OF THE LIGHT FAILURE SENSOR IS ACTIVATED.
AS A RESULT, THE CURRENT FLOWS FROM TERMINAL 4 OF THE LIGHT FAILURE SENSOR " TERMINAL 11 " GROUND AND TURNS
THE REAR LIGHT WARNING LIGHT ON. BY PRESSING THE BRAKE PEDAL, THE CURRENT FLOWING TO TERMINAL 8 OF THE LIGHT
FAILURE SENSOR KEEPS THE WARNING CIRCUIT ON HOLD AND THE WARNING LIGHT ON UNTIL THE IGNITION SW IS TURNED OFF.
S12 STOP LIGHT SW
2±1: CLOSED WITH BRAKE PEDAL DEPRESSED
L 3 LIGHT FAILURE SENSOR
1, 2, 7±GROUND : APPROX. 12 VOLTS WITH STOP LIGHT SW ON
4, 8±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
11±GROUND : ALWAYS CONTINUITY
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C13B28H 930R1131
C14A28L 330S1229
H 830R1031
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1C20FLOOR WIRE
1E20INSTRUMENT PANEL WIRE
1H20COWL WIRE1I20COWL WIRE
3A22INSTRUMENT PANEL WIRE3D22INSTRUMENT PANEL WIRE
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
BU140FLOOR WIRE AND INSTRUMENT PANEL WIRE (LEFT KICK PANEL)
Bc140FLOOR NO. 3 WIRE AND FLOOR WIRE (UNDER THE LEFT SIDE OF REAR SEAT CUSHION)
Bd140FLOOR NO. 3 WIRE AND LUGGAGE NO. 2 WIRE (RIGHT SIDE OF LUGGAGE COMPARTMENT)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
BL40UNDER THE CENTER PILLAR RH
BM40BACK PANEL CENTER
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
B1040FLOOR MAIN WIREB1540FLOOR MAIN WIRE
B1440FLOOR MAIN WIREB2140FLOOR NO. 3 WIRE
SYSTEM OUTLINE
SERVICE HINTS
WhereEverybodyKnowsYourName

88
TAILLIGHT
WHEN THE LIGHT CONTROL SW IS TURNED TO TAIL OR HEAD POSITION. THE CURRENT FLOWS TO TERMINAL 3 OF THE LIGHT
FAILURE SENSOR THROUGH THE TAIL FUSE.
WHEN THE IGNITION SW IS TURNED ON, THE CURRENT FLOWS FROM THE GAUGE FUSE TO TERMINAL 8 OF THE LIGHT FAILURE
SENSOR, AND ALSO FLOWS THROUGH THE REAR LIGHT WARNING LIGHT TO TERMINAL 4 OF THE LIGHT FAILURE SENSOR.
TAILLIGHT DISCONNECTION WARNING
WITH THE IGNITION SW ON AND THE LIGHT CONTROL SW TURNED TO TAIL OR HEAD POSITION. IF THE TAILLIGHT CIRCUIT IS
OPEN, THE LIGHT FAILURE SENSOR DETECTS THE FAILURE BY THE CHANGE IN CURRENT FLOWING FROM TERMINAL 3 OF THE
LIGHT FAILURE SENSOR TO TERMINAL 9, 11 AND THE WARNING CIRCUIT OF THE LIGHT FAILURE SENSOR IS ACTIVATED.
AS A RESULT, THE CURRENT FLOWS FROM TERMINAL 4 OF THE LIGHT FAILURE SENSOR " TERMINAL 11 " GROUND AND TURNS
THE REAR LIGHT WARNING LIGHT ON, WHICH REMAINS ON UNTIL THE LIGHT CONTROL SW IS TURNED O\
FF.
TAILLIGHT RELAY
5±3 : CLOSED WITH LIGHT CONTROL SW AT TAIL OR HEAD POSITION
L 3 LIGHT FAILURE SENSOR
4, 8±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
3±GROUND : APPROX. 12 VOLTS WITH LIGHT CONTROL SW AT TAIL OR HEAD POSITION
11±GROUND : ALWAYS CONTINUITY
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C13B28F 526L 230
C14A28F 626L 330
C1528F 926R1031
F 326I16A29 (USA)R1131
F 426I16B29 (CANADA)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A20ENGINE ROOM MAIN WIRE1B20ENGINE ROOM MAIN WIRE
1C20FLOOR WIRE
1E20INSTRUMENT PANEL WIRE
1J20COWL WIRE1K20COWL WIRE
3A22INSTRUMENT PANEL WIRE3D22INSTRUMENT PANEL WIRE
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
BU140FLOOR WIRE AND INSTRUMENT PANEL WIRE (LEFT KICK PANEL)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EA34FRONT SIDE OF RIGHT FENDER
IF36LEFT KICK PANEL
BM40BACK PANEL CENTER
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E 1E1134ENGINE ROOM MAIN WIRE
E 434ENGINE ROOM MAIN WIREB1440FLOOR MAIN WIREE 534ENGINE ROOM MAIN WIREB1540FLOOR MAIN WIRE
SYSTEM OUTLINE
SERVICE HINTS
WhereEverybodyKnowsYourName

11 6
THEFT DETERRENT AND DOOR LOCK CONTROL
D 7, D 8 DOOR KEY LOCK AND UNLOCK SW LH, RH
1±2 : CLOSED WITH DOOR LOCK CYLINDER UNLOCKED WITH KEY
3±2 : CLOSED WITH DOOR LOCK CYLINDER LOCKED WITH KEY
D10, D11 DOOR LOCK MOTOR, DOOR UNLOCK DETECTION SW AND DOOR OPEN DETECTION SW LH, RH
1±4: CLOSED WITH UNLOCK POSITION
E 5 ENGINE HOOD COURTESY SW
1±2: CLOSED WITH ENGINE HOOD OPEN
I15 UNLOCK WARNING SW [IGNITION SW]
9±10: CLOSED WITH IGNITION KEY IN CYLINDER
L 5 LUGGAGE COMPARTMENT KEY UNLOCK SW
1±3: CLOSED WITH DOOR LOCK CYLINDER UNLOCK WITH KEY
L 6 LUGGAGE COMPARTMENT LIGHT SW
1±GROUND: CLOSED WITH DOOR OPEN
T 8(B) THEFT DETERRENT AND DOOR LOCK ECU
1±GROUND: CONTINUITY WITH LUGGAGE COMPARTMENT DOOR TO UNLOCK POSITION
12±GROUND: CONTINUITY WITH ENGINE HOOD OPEN
10±GROUND: CONTINUITY WITH LUGGAGE COMPARTMENT DOOR OPEN
7±GROUND: APPROX. 12 VOLTS WITH IGNITION SW AT ACC OR ON POSITION
T 9(A) THEFT DETERRENT AND DOOR LOCK ECU
1±GROUND: APPROX. 12 VOLTS WITH SHIFT LEVER IN N OR P POSITION AND IGNITION SW AT ST POSITION
2±GROUND: APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
6±GROUND: CONTINUITY WITH IGNITION KEY IN CYLINDER
7±GROUND: CONTINUITY WITH FRONT RH DOOR TO UNLOCK POSITION
8±GROUND: ALWAYS APPROX. 12 VOLTS
10±GROUND: CONTINUITY WITH DOOR LOCK KEY SW LH TO UNLOCK POSITION
11±GROUND: CONTINUITY WITH FRONT LH DOOR TO UNLOCK POSITION
12±GROUND: CONTINUITY WITH FRONT RH DOOR OPENED
13±GROUND: CONTINUITY WITH FRONT LH DOOR OPENED
14±GROUND: CONTINUITY WITH DOOR LOCK KEY SW RH TO LOCK POSITION
15±GROUND: CONTINUITY WITH DOOR LOCK KEY SW RH TO UNLOCK POSITION
20±GROUND: ALWAYS APPROX. 12 VOLTS
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C1428F 926N 127
C2328F1028P 531
D 730F1430T 127
D 830I1529T 8B29
D 930L 129T 9A29
D1030L 430T1529
D1130L 530
E 526L 630
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
219ENGINE COMPARTMENT LEFT
422LEFT KICK PANEL (J/B NO.1 LEFT)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B20ENGINE ROOM MAIN WIRE
1D20FRONT DOOR LH WIRE
1E20INSTRUMENT PANEL WIRE
1H
1I20COWL WIRE1J20COWL WIRE
1K
3A22INSTRUMENT PANEL WIRE3F22INSTRUMENT PANEL WIRE
SERVICE HINTS
WhereEverybodyKnowsYourName

11 7
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EB134ENGINE WIRE AND ENGINE ROOM MAIN WIRE (FRONT SIDE OF R/B NO.2)
IE136ENGINE ROOM MAIN WIRE AND COWL WIRE (R/B NO.4)
IF236FRONT DOOR LH WIRE AND COWL WIRE (LEFT KICK PANEL)
IG136INSTRUMENT PANEL WIRE AND COWL WIRE (R/B NO.5)
IJ136ENGINE WIRE AND COWL WIRE (RIGHT KICK PANEL)IJ236ENGINE WIRE AND COWL WIRE (RIGHT KICK PANEL)
IP138FRONT DOOR RH WIRE AND COWL WIRE (RIGHT KICK PANEL)
BT140FLOOR WIRE AND COWL WIRE (LEFT KICK PANEL)
BY140INSTRUMENT PANEL WIRE AND FLOOR NO.3 WIRE (RIGHT KICK PANEL)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EA34FRONT SIDE OF RIGHT FENDER
IF36LEFT KICK PANEL
IH36UNDER THE ASHTRAY LH
IJ36RIGHT KICK PANEL
BL40UNDER THE CENTER PILLAR RH
BM40BACK PANEL CENTER
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
I 738COWL WIREB 740FRONT DOOR RH WIREI1138COWL WIREB3340FRONT DOOR RH WIRE
B 440FRONT DOOR LH WIRE
WhereEverybodyKnowsYourName

15
ABBREVIATIONS
DISCONNECTION AND CONNECTION OF BOLT
TYPE CONNECTORS
For engine and ECT ECU in this vehicle, connectors are used
which require a bolt built into the connector to be screwed down to
securely connect the connector.
1. Disconnect the connectorAfter completely loosening the bolt, the two parts of the
connector can be separated.
NOTICE:
Do not pull the wire harness when disconnecting the
connector.
2. Connect the connector
NOTICE:
Before connecting the connector, always check that the
terminals are not bent or damaged.
(a) Match the guide section of the male connectorcorrectly with the female connector, then press them
together.
(b) Tighten the bolt. Make sure the connectors are completely connected,
by tightening the bolt until there is a clearance of less
than 1 mm (0.04 in.) between the bottom of male
connector and the end of female connector.
ABBREVIATIONS
The following abbreviations are used in this manual.
A/C = Air Conditioning O/D = Overdrive
ABS = Anti±Lock Brake System R/B = Relay Block
A/T = Automatic Transmission RH = Right±Hand
CB = Circuit Breaker SRS = Supplement Restraint System
COMB. = Combination SW = Switch
ECT = Electronic Controlled Transmission TDCL = Total Diagnostic Communication Link
ECU = Electronic Control Unit TEMP. = Temperature
EGR = Exhaust Gas Recirculation TRAC = Traction Control
FL = Fusible Link VSV = Vacuum Switching Valve
ISC = Idle Speed Control W/ = With
J/B = Junction Block W/O = Without
LH = Left-Hand
* The titles given inside the components are the names of the terminals (ter\
minal codes) and are not treatedas being abbreviations.
WhereEverybodyKnowsYourName

105
TURN SIGNAL FLASHER
(4) 3 ± GROUND: CHANGES FROM APPROX. 12 VOLTS TO 0 VOLTS WITH IGNITION SW ON AND TURN SIGNAL SW LEFT, OR WITH
HAZARD SW ON
(4) 5 ± GROUND: CHANGES FROM APPROX. 12 VOLTS TO 0 VOLTS WITH IGNITION SW ON AND TURN SIGNAL SW RIGHT, OR WITH
HAZARD SW ON
(4) 4 ± GROUND: CONTINUITY WITH TURN SIGNAL SW LEFT, OR HAZARD SW ON
(4) 2 ± GROUND: CONTINUITY WITH TURN SIGNAL SW RIGHT, OR HAZARD SW ON
(4) 1 ± GROUND: APPROX. 12 VOLTS WITH IGNITION SW ON OR HAZARD SW ON
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C13A28F 726R1031
C14B28F 826R1131
C1628H 729
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
219ENGINE COMPARTMENT LEFT
423LEFT KICK PANEL (J/B NO.1 LEFT)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A20ENGINE ROOM MAIN WIRE
1C20FLOOR WIRE
1E20INSTRUMENT PANEL WIRE
1H
1J20COWL WIRE
1K
20COWL WIRE
3A
3D22INSTRUMENT PANEL WIRE
3G
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IE136ENGINE ROOM MAIN WIRE AND COWL WIRE (R/B NO. 4)
IG136INSTRUMENT PANEL WIRE AND COWL WIRE (R/B NO 5)IG236INSTRUMENT PANEL WIRE AND COWL WIRE (R/B NO. 5)
IQ138INSTRUMENT PANEL WIRE AND CONSOLE BOX WIRE (UNDER THE INSTRUMENT PANEL CENTER)IQ238INSTRUMENT PANEL WIRE AND CONSOLE BOX WIRE (UNDER THE INSTRUMENT PA N E L CENTER)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EA34FRONT SIDE OF RIGHT FENDER
EB34FRONT SIDE OF LEFT FENDER
IF36LEFT KICK PANEL
BM40BACK PANEL CENTER
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
I 738COWL WIREB1540FLOOR MAIN WIRE
SERVICE HINTS
WhereEverybodyKnowsYourName

185
CURRENT ALWAYS FLOWS TO TERMINAL 1 OF THE INTEGRATION RELAY THROUGH DOME FUSE.
1. SEAT BELT WARNING SYSTEM
WHEN THE IGNITION SW IS TURNED ON, CURRENT FLOWS FROM THE GAUGE FUSE TO TERMINAL 7 OF THE INTEGRATION RELAY.
AT THE SAME TIME, CURRENT FLOWS TO TERMINAL 9 OF THE RELAY FROM THE GAUGE FUSE THROUGH THE SEAT BELT
WARNING LIGHT. THIS CURRENT ACTIVATES THE INTEGRATION RELAY AND, FOR APPROX. 4±8 SECONDS, CURRENT FLOWING
THROUGH THE WARNING LIGHT FLOWS FROM TERMINAL 9 OF THE RELAY " TERMINAL 10 " GROUND, CAUSING THE WARNING
LIGHT TO LIGHT UP. AT THE SAME TIME AS THE WARNING LIGHT LIGHTS UP, A BUCKLE SW OFF SIGNAL IS INPUT TO TERMINAL 8
OF THE RELAY, THE CURRENT FLOWING TO TERMINAL 7 OF THE RELAY FLOWS FROM TERMINAL 10 " GROUND AND THE SEAT
BELT WARNING BUZZER SOUNDS FOR APPROX. 4±8 SECONDS. HOWEVER, IF THE SEAT BELT IS PUT ON DURING THIS PERIOD
(WHILE THE BUZZER IS SOUNDING), SIGNAL INPUT TO TERMINAL 8 OF RELAY STOPS AND THE CURRENT FLOW FROM TERMINAL 7
OF THE RELAY " TERMINAL 10 " GROUND IS CUT, CAUSING THE BUZZER TO STOP.
2. UNLOCK WARNING SYSTEM
WITH THE IGNITION KEY INSERTED IN THE KEY CYLINDER (UNLOCK SW ON), THE IGNITION SW STILL OFF AND \
DOOR OPEN (DOOR
COURTESY SW ON), WHEN A SIGNAL IS INPUT TO TERMINAL 6 OF THE RELAY, THE INTEGRATION RELAY OPERATES, CURRENT
FLOWS FROM TERMINAL 7 OF THE RELAY " TERMINAL 10 " GROUND AND UNLOCK WARNING BUZZER SOUNDS.
B 4 BUCKLE SW LH
1±2 : CLOSED WITH DRIVER'S LAP BELT IN USE
D10 DOOR COURTESY SW LH
3±6 : CLOSED WITH LH DOOR OPEN
I15 UNLOCK WARNING SW [IGNITION SW]
10±9: CLOSED WITH IGNITION KEY IN CYLINDER
INTEGRATION RELAY
10±GROUND: ALWAYS CONTINUITY6±GROUND: CONTINUITY WITH DRIVER'S DOOR OPEN
5±GROUND: CONTINUITY WITH IGNITION KEY IN CYLINDER
8±GROUND: CONTINUITY WITH DRIVER'S LAP BELT IN USA
9±GROUND: 0 VOLTS FOR 4±8 SECONDS WITH IGNITION SW ON AND APPROX. 12 VOLTS 4±8 SECONDS AFTER IGNITION SW ON
1±GROUND: ALWAYS APPROX. 12 VOLTS
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
B 432C14B28I1529
C12A28D1030
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
219ENGINE COMPARTMENT LEFT
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B20ENGINE ROOM MAIN WIRE
1C20FLOOR MAIN
1D20FRONT DOOR LH WIRE
1E20INSTRUMENT PANEL WIRE
1H
1I20COWL WIRE
1J
20COWL WIRE
3A22INSTRUMENT PANEL WIRE3D22INSTRUMENT PANEL WIRE
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
Ba142FLOOR WIRE AND FRONT SEAT LH WIRE (UNDER THE FRONT LH SEAT)Ba242FLOOR WIRE AND FRONT SEAT LH WIRE (UNDER THE FRONT LH SEAT)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IF36LEFT KICK PANEL
BK40UNDER THE CENTER PILLAR LH
SYSTEM OUTLINE
SERVICE HINTS
WhereEverybodyKnowsYourName