sensor LEXUS SC300 1991 Service Repair Manual

OKNG
OKNG
3Check center airbag sensor assembly.
C
OK
Hint
P1. Connect connector to center airbag sensor connec-
tor.
2. Connect connector between center airbag sensor assembly and wiring harness connector.
3. Using a service wire, connect D
+ and D±, P+ and P±.
4. Connect negative (±) terminal cable to battery, and wait at least 2 seconds.
1. Turn ignition switch ACC or ON and wait at least 20 seconds. Clear malfunction code. Turn ignition
switch LOCK and wait at least 20 seconds.
2. Turn ignition switch ACC or ON , and wait at least 20 seconds.
3. Using SST, connect terminals Tc and E
1 of DLC2.
SST 09843±18020
4. Check diagnostic trouble code.
Diagnostic trouble code 54 is not output.
Codes other t han code 54 may be output at this time, but
this is not relevant to this check.
Replace center airbag sensor assembly.
4Check P squib.
C
OK
Hint
P1. Turn ignition switch LOCK.
2. Disconnect battery negative (±) terminal cable, and
wait at least 90 seconds.
3. Connect front passenger airbag assembly connec- tor.
4. Connect negative (±) terminal cable to battery, and wait at least 2 seconds.
1. Turn ignition switch ACC or ON and wait at least 20 seconds. Clear malfunction code. Turn ignition
switch LOCK and wait at least 20 seconds.
2. Turn ignition switch ACC or ON, and wait at least 20
seconds.
3. Using SST, connect terminals Tc and E
1 of DLC2.
SST 09843±18020
4. Check diagnostic trouble code.
Diagnostic trouble code 54 is not output.
Codes other t han code 54 may be output at this time, but
this is not relevant to this check.
Replace front passenger airbag assembly.
From the results of the above inspection, the malfunctioning part can now be\
considered normal. To
make sure of this, use the simulation method to check.
RS±118±
SUPPLEMENTAL RESTRAINT SYSTEM TROUBLESHOOTING
WhereEverybodyKnowsYourName

YESNO
INSPECTION PROCEDURE
1Does SRS warning light turn off?
C
Hint
P1. Turn ignition switch LOCK.
2. Disconnect negative (±) terminal cable from battery
and wait at least 90 seconds.
3. Remove steering wheel pad (See page RS±19).
4. Disconnect connectors of front passenger airbag assembly (See page RS±32).
5. Disconnect center airbag sensor assembly con- nector.
6. Connect negative (±) terminal cable to battery.
Check operation of SRS warning light.
Ignition Switch is LOCK position.
Check SRS warning light circuit or terminal AB circuit of
DCL1 or DLC2.
Replace center airbag sensor assembly.
RS±120±
SUPPLEMENTAL RESTRAINT SYSTEM TROUBLESHOOTING
WhereEverybodyKnowsYourName

Tc Terminal Circuit
CIRCUIT DESCRIPTION
By connecting terminal Tc and E1 of the DLC1 or DLC2, the center airbag sensor assembly is set in the di\
agnos-
tic trouble code output mode. The diagnostic trouble codes are displayed\
by the blinking of the SRS warning
light.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
Troubleshooting for this system is different depending on whether the diagnostic trouble code is not displayed\
SRS warning light is always lit up with a DTC check procedure, or is displa\
yed without a DTC check procedure.
Confirm the problem symptoms first before selecting the appropriate troubleshoo\
ting procedure.
HINT: If the diagnostic trouble code is not displayed or SRS warning light is\
always lit up with a DTC check proce-
dure perform the following troubleshooting:
±
SUPPLEMENTAL RESTRAINT SYSTEM TROUBLESHOOTINGRS±121
WhereEverybodyKnowsYourName

NGOK
3Check center airbag sensor assembly.
C
OK
P1. Turn ignition switch LOCK.
2. Disconnect battery negative (±) terminal cable, andwait at least 90 seconds.
3. Remove steering wheel pad (See page RS±19).
4. Disconnect connectors of front passenger airbag assembly (See page RS±32).
Check operation of SRS warning light.
SRS warning light comes on.
Check harness between center airbag sensor assembly
and DLC1 or DLC2.
Replace center airbag sensor assembly.
RS±124±
SUPPLEMENTAL RESTRAINT SYSTEM TROUBLESHOOTING
WhereEverybodyKnowsYourName

NGOK
HINT: If the diagnostic trouble code is continuously displayed, perform the f\
ollowing troubleshooting.
1Check resistance between terminal Tc of center airbag sensor assembly and body ground.
C
OK
P1. Turn ignition switch LOCK.
2. Disconnect center airbag sensor assembly con-nector.
3. Disconnect battery negative (±) terminal cable, and wait at least 90 seconds.
4. Remove steering wheel pad (See page RS±19).
5. Disconnect connectors of front passenger airbag assembly (See page RS±32).
Check resistance between terminal Tc of center airbag
sensor assembly and body ground.
Resistance: 1 M
or higher
Replace center airbag sensor assembly.
Repair or replace harness or connector.
±
SUPPLEMENTAL RESTRAINT SYSTEM TROUBLESHOOTINGRS±125
WhereEverybodyKnowsYourName

SERVICE SPECIFICATIONS
SERVICE DATA
RS02S±01
\
\
FRONT AIRBAG SENSOR\
 \

\
\

S ±
A\
 \
755±855

\
\

S ± S\
 \
1 M
or Higher
\
\
 S ± A\
 \
Less than 1

TORQUE SPECIFICATIONS
RS02T±07
\
\
Part tightened NVm kgf Vcm ft Vlbf
\
\
Steering wheel 35 360 26
\
\
Steering wheel pad 7.4 75 65 in. Vlbf
\
\
Front passenger airbag assembly 21 210 15
\
\
Front airbag sensor 25 260 19
\
\
Center airbag sensor assembly 15 150 11
RS±126±
SUPPLEMENTAL RESTRAINT SYSTEM SERVICE SPECIFICATIONS
WhereEverybodyKnowsYourName

GENERAL DESCRIPTION
The LEXUS SC400/300 is equipped with an SRS (Supplemental Restraint System\
) such as the driver
airbag and front passenger airbag. Failure to carry out service operations in \
the correct sequence
could cause the SRS to unexpectedly deployed during servicing, possibly leadin\
g to a serious acci-
dent. Further, if a mistake is made in servicing the supplemental restraint system, i\
t is possible the
SRS may fail to operate when required. Before performing servicing (inc\
luding removal or installa-
tion of parts, inspection or replacement), be sure to read the followin\
g items carefully, then follow
the correct procedure described in the repair manual.
1. Malfunction symptoms of the supplemental restraint system are difficult to confirm, so the diagnostic trouble codes become the most important source of information when troubleshooting. When
troubleshooting the supplemental restraint system, always inspect the diagnostic trouble codes before
disconnecting the battery (See page RS±59).
2. Work must be started after 90 seconds from the time the ignition switch turn\
ed to the LOCK position
and the negative (±) terminal cable is disconnected from the battery. (The supplemental restraint
system is equipped with a back±up power source so that if work is sta\
rted within 90 seconds of
disconnecting the negative (±) terminal cable of the battery, the SRS may be deployed.)
When the negative (±) terminal cable is disconnected from the battery, memory of the clock and audio sys-
tems will be canceled. So before starting work, make a record of the contents memo\
rized by the audio
memory system. When work is finished, reset the audio systems as before and ad\
just the clock. When the
vehicle has power tilt and power telescopic steering, power seat, power outside rear view mirror and power
shoulder belt anchorage, which are all equipped with memory function, it is not \
possible to make a record
of the memory contents. So when the work is finished, it will be necessary\
to explain this fact to the custom-
er, and ask the customer to adjust the features and reset the memory.
To avoid erasing the memory of each memory system, never use a back±up\
power supply from outside
the vehicle.
3. Even in cases of a minor collision where the SRS does not deploy, the steering wheel pad, front passenger
airbag assembly, front airbag sensors and center airbag sensor assembly should be inspe\
cted (See pages
RS±16 , 28 , 41 and 44).
4. Never use SRS parts from another vehicle. When replacing parts, replace \
them with new parts.
5. Before repairs, remove the airbag sensor if shocks are likely to be applied to the sensors during r\
epairs.
6. Never disassemble and repair the steering wheel pad, front passenger airbag a\
ssembly, front airbag sensors or center airbag sensor assembly in order to reuse it.
7. If the steering wheel pad, front passenger airbag assembly, front airbag sensors or center airbag sensor assembly have been dropped, or if there are cracks, dents or dents or ot\
her defects in the case, bracket
or connector, replace them with new ones.
8. Do not expose the steering wheel pad, front passenger airbag assembly, front airbag sensors and center airbag sensor assembly directly to hot air or flames.
9. Use a volt/ohmmeter with high impedance (10 k
/V minimum) of troubleshooting of the system's electrical
circuit.
10. Information labels are attached to the periphery of the SRS components. \
Follow the instructions on the
notices.
11. After work on the supplemental restraint system is completed, perform the SRS\
warning light check (See page RS±59 ).
12. If the vehicle is equipped with a mobile communication system, refer to \
the precaution in the IN section. RS±2
±
SUPPLEMENTAL RESTRAINT SYSTEM GENERAL DESCRIPTION
WhereEverybodyKnowsYourName

FRONT AIRBAG SENSOR
RS00N±07
1. Never reuse the front airbag sensor involved in a collision when the airbag h\
as deployed. (Replace boththe left and right airbag sensors.)
2. Install the front airbag sensor with the arrow on the sensor facing towa\
rd the front of the vehicle.
3. The front airbag sensor set bolts have been anti±rust treated. When the \
sensor is removed, always replace
the set bolts with new ones.
4. The front airbag sensors is equipped with an electrical connection check me\
chanism. Be sure to lock this mechanism securely when connecting the connector. If the connector is not securely locked, a malfunction
code will be detected by the diagnosis system (See page RS±12).
CENTER AIRBAG SENSOR ASSEMBLY
RSOOR±0A
1. Never reuse the center airbag sensor assembly involved in a collision when the airbag has
deployed.
2. Work must be started after 90 seconds from the time the ignition switch is t\
urned to LOCK position and the negative (±) terminal cable is disconnected from the batter\
y even just loosing the set bolts
of center airbag sensor assembly.
WIRE HARNESS AND CONNECTOR
RSO41±01
The SRS wire harness is integrated with the cowl wire harness assembly. The wires for the SRS wire har-
ness are encased in a yellow corrugated tube. All the connectors for the sys\
tem are also a standard yellow
color. If the SRS wire harness becomes disconnected or the connector becomes broken du\
e to an accident
etc., repair or replace it as shown on page RS±48.
±
SUPPLEMENTAL RESTRAINT SYSTEM GENERAL DESCRIPTIONRS±5
WhereEverybodyKnowsYourName

DESCRIPTION
RS00S±02
The SRS (Supplemental Restraint System), together with the seat belt, is designed to help protect the driv-
er. Frontal inspect, the airbag sensor detect the shock, and if the front±\
to±rear shock is greater than a spe-
cified value, an airbag stored in the steering wheel pad is inflated ins\
tantaneously to help reduce the shock
to the driver.
LOCATION OF COMPONENTS
RS00T±02
RS±6±
SUPPLEMENTAL RESTRAINT SYSTEM DESCRIPTION
WhereEverybodyKnowsYourName

CENTER AIRBAG SENSOR ASSEMBLY CONNECTOR
RS00V±0B
 No. Symbol Terminal Name A ± Electrical Connection Check Mechanism B ± Electrical Connection Check Mechanism 1 P± Squib (Passenger) 2 P+ Squib
(Passenger) 3 D+ Squib
(Driver) 4 D± Squib  (Driver) 5 E1 Ground 6 E2 Ground 7 Tc Diagnosis 8 +SR Front Airbag Sensor RH
 9 ±SR Front Airbag Sensor RH  10 ±SL Front Airbag Sensor LH  11 +SL Front Airbag Sensor LH
 12 LA SRS Warning Light 13 IG2 Power Source (IGN Fuse) 14 ACC Power Source (CIG Fuse)
RS±8±
SUPPLEMENTAL RESTRAINT SYSTEM DESCRIPTION
WhereEverybodyKnowsYourName