check engine light LEXUS SC300 1999 Owners Manual

GAUGES, METERS AND SERVICE REMINDER INDICATORS
54(a) If parking brake is
off, stop and
check.
(b) Fasten seat belts.
(Indicator and buzzer)
(c) Take vehicle to Lexus dealer
immediately.
(d) Stop and check.
(e) Stop and check. (f) Add engine oil.

(g) Take vehicle to Lexus dealer.
(h) Take vehicle to Lexus dealer.
(i) Close all doors.
(j) Replace bulb.
(k) Take vehicle to Lexus dealer.
(l) Add washer fluid.
(m) Low fuel level Fill up tank. warning light
(n) Key reminder buzzer Remove key.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
56If the brake fluid level is correct ...
Have the warning system checked by your Lexus dealer.
(b) Seat Belt Reminder Light and Buzzer
Once the ignition key is turned to ºONº or ºSTARTº, the
reminder
light flashes and buzzer comes on if the driver's seat
belt is not fastened. Unless the driver fastens the belt, the light
stays flashing and the buzzer stops after about 4 to 8 seconds.
(c) SRS Airbag Warning Light
This indicator comes on when the ignition key is turned to
the ºACCº or ºONº position. It goes off after about 6
seconds. This means the SRS airbag system is operating
properly.
The SRS airbag warning light system monitors the airbag
sensor assembly, inflators, warning light, interconnecting
wiring and power sources.
If either of the following conditions occurs, this indicates a
malfunction somewhere in the parts monitored by the
warning light system. Contact your Lexus dealer as soon as
possible to service the vehicle.

The light does not come on as described above or remains
on.

The light comes on while driving.
(d) Discharge Warning Light
This light warns that the battery is being discharged.
If it comes on while you are driving, stop the vehicle, turn off
the engine, and check for the cause. Look first at the engine
drive belt.

If it is loose or broken, the generator will not charge the
battery properly.

If the belt is O.K., there is a problem somewhere in the
charging system.
The engine ignition will continue to operate, however, until
the battery is discharged. Turn off the air conditioning,
blower, radio, etc., and drive directly to the nearest Lexus
dealer or repair shop.
NOTICE
Do not continue driving if the engine drive belt is broken
or loose.
(e) Low Oil Pressure Warning Light
This light warns that the engine oil pressure is too low.
If it flickers or stays on while you are driving, pull off the road
to a safe place and stop the engine immediately. Call a Lexus
dealer or qualified repair shop for assistance.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
57
The light may occasionally flicker when the engine is idling
or it may come on briefly after a hard stop. There is no cause
for concern if it then goes out when the engine is accelerated
slightly.
The light may come on when the oil level is extremely low.
It is not designed to indicate low oil level, and the oil level
must be checked using the oil level dipstick.
NOTICE
Do not drive the vehicle with the warning light on ± even
for one block. It may ruin the engine.
(f) Low Engine Oil Level Warning Light
This light warns that the engine oil level is too low. Add oil
as soon as possible. (For instructions, see ºChecking the
engine oil levelº on page 342.)
While driving on steep inclines or rough roads which causes
the vehicle to substantially sway or on curves, this light may
come on due to the movement of engine oil in the engine.
NOTICE
Continued engine operation with low engine oil will
damage the engine.
(g) Malfunction Indicator Lamp
This lamp comes on in the following cases.
a. The fuel tank is completely empty. (See ºFuel gaugeº on
page 49 for instructions.)
b. The fuel tank cap is not tightened securely (SC400 only).
(See ºFuel tank capº on page 85 for instructions.)
c. There is a problem
somewhere in your engine or automatic
transmission electrical system.
If it comes on while you are driving in case ºc.º, have your
vehicle checked/repaired by your Lexus dealer as soon as
possible.
(h) ºABSº Warning Light
This light warns that there is a problem somewhere in your
anti±lock brake system.
If the light comes on while you are driving, have your vehicle
checked by your Lexus dealer as soon as possible.
The light will come on when the ignition key is turned to
ºONº, and will go off after about a few seconds.
When the ºABSº warning light is on (and the brake system
warning light is off), the brake system operates
conventionally but anti±lock brake system is not assisting
brake performance so that the wheels could lock up during a
sudden brake or braking on slippery road surfaces.

STARTING AND DRIVING
216
HOW TO START THE ENGINE
Before cranking
1. Apply the parking brake firmly.
2. Turn off unnecessary lights and accessories.
3. Put the selector lever in ºPº. If you need to restart the
engine while the vehicle is moving, put the selector lever in
ºNº. A starter safety device will prevent the starter from
operating if the selector lever is in any drive position.
4. Depress the brake pedal and hold it to the floor until you
are ready to drive off.
Starting the engine
Before starting the engine, be sure to follow the instructions
in ºBefore crankingº.
Normal starting procedure
The multiport fuel injection system/sequential multiport fuel
injection system in your engine automatically controls the
proper air±fuel mixture for starting. You can start a cold or
hot engine as follows:1. With your foot off the accelerator pedal, crank the engine
by turning the key to ºSTARTº. Release it when the engine
starts.
2. After the engine runs for about 10 seconds, you are ready
to drive.
If the weather is below freezing, let the engine warm up for
a few minutes before driving. Do not leave the vehicle while
the engine is warming up.
If the engine stalls ...
Simply
restart it , using the correct procedure given in normal
starting.
If the engine will not start
See ºIf your vehicle will not startº on page 275.
NOTICE
 Do not crank for more than 30 seconds at a time. This
may overheat the starter and wiring systems.
 Do not race a cold engine.
 If the engine becomes difficult to start or stalls
frequently, have the engine checked immediately.

STARTING AND DRIVING
245
If the vehicle speed falls below about 40 km/h (25 mph), the
preset speed will be automatically cancelled.
If the vehicle speed drops 16 km/h (10 mph) below the preset
speed, the preset speed will also automatically be cancelled.
If the preset speed automatically cancels out for other than
these reasons, have your vehicle checked by your Lexus
dealer at the earliest opportunity.
Resetting to a faster speed
Press the control lever upward in the ºRES/ACCº direction
and hold it. Release the lever when the desired speed is
attained. While the lever is held upward, the vehicle will
gradually gain speed.
When
the difference between the actual vehicle speed and the
set speed is less than 5 km/h (3 mph), the set speed can be
increased 1.6 km/h (1 mph) each time by pressing the control
lever upward in the ºRES/ACCº direction quickly within 0.6
seconds.
However, a quicker way to reset is to accelerate the vehicle
and then press the control lever downward in the
ºSET/COASTº direction.
Resetting to a slower speed
Press the control lever downward in the ºSET/COASTº
direction and hold it. Release the lever when the desired
speed is attained. While the lever is held downward, the
vehicle speed will gradually decrease. When
the difference between the actual vehicle speed and the
set speed is less than 5 km/h (3 mph), the set speed can be
lowered 1.6 km/h (1 mph) each time by pressing the control
lever downward in the ºSET/COASTº direction quickly
within 0.6 seconds.
However, a quicker way to reset is to depress the brake pedal
and then press the control lever downward in the
ºSET/COASTº direction.
Even if you downshift the transmission from ºDº to º4º
(SC400) or from ºDº to º3º (SC300) with the cruise control
on, engine braking will not be applied because the cruise
control is not cancelled. To decrease the vehicle speed, reset
to a slower speed with the cruise control lever or depress the
brake pedal. If you use the brake pedal, cruise control is
cancelled.
Resuming the preset speed
If the preset speed is cancelled by pulling the control lever or
by depressing the brake pedal, pushing the lever up in the
ºRES/ACCº direction will restore the speed set prior to
cancellation. However, once the vehicle speed falls below
about 40 km/h (25 mph), the preset speed will not be resumed.
Cruise control failure warning
If the ºCRUISEº indicator light in the instrument cluster
flashes five times and then goes out when using the cruise
control, it means that there is trouble in the cruise control
system. Contact your Lexus dealer.

STARTING AND DRIVING
247
You can turn off the traction control system by pushing
the ºTRAC OFFº switch. The ºTRAC OFFº indicator/
warning light will then come on. Pushing the ºTRAC
OFFº switch a second time turns the system back on and
extinguishes the ºTRAC OFFº indicator/warning light.
You may hear a slight clicking noise in the engine
compartment when the engine is started. This means that the
traction control system is in the self±check mode, and does
not indicate malfunction.
When the traction control system is operating, you may feel
vibration of your vehicle, caused by operation of the brakes.
This indicates the system is functioning properly.
When getting the vehicle out of mud or new snow, etc. the
traction control system will help operate to prevent the wheels
from spinning.

DRIVING TIPS
259
BREAK±IN PERIOD
Drive gently and avoid high speeds.
You need not follow a break±in schedule with your new
Lexus. But following a few simple tips for the first 1600 km
(1000 miles) can add to the future economy and long life of
your vehicle:

Do not drive over 88 km/h (55 mph).

Avoid overrevving. Maintain engine speed between 2000
and 4000 rpm.

Avoid full±throttle starts.

Try to avoid hard stops during the first 300 km (200 miles).

Do not drive for a long time at any single speed, either fast
or slow.

Do not tow a trailer during the first 800 km (500 miles).
OPERATION IN FOREIGN
COUNTRIES
If you plan to drive your Lexus in another country ...
First, comply with the vehicle registration laws.
Second, confirm the availability of the correct fuel (unleaded
and minimum octane rating).
TIPS FOR DRIVING IN VARIOUS CONDITIONS

Always slow down in gusty crosswinds. This will allow
you much better control.

Drive slowly onto curbs and, if possible, at a right angle.
Avoid driving onto high, sharp±edged objects and other
road hazards. Failure to do so can lead to severe tire
damage resulting in tire bursts.

When parking on a hill, turn the front wheels until they
touch the curb so that the vehicle will not roll. Apply the
parking brake, and place the transmission in ºPº. If
necessary, block the wheels.

Washing your vehicle or driving through deep water may
get the brakes wet. To see whether they are wet, check that
there is no traffic near you and then press the pedal lightly.
If you do not feel a normal braking force, the brakes are
probably wet. To dry them, drive the vehicle cautiously
while lightly pressing the brake pedal with the parking
brake applied. If they still do not work safely, pull to the
side of the road and call a Lexus dealer for assistance.
CAUTION

Before driving, make sure the parking brake is fully
released and that the parking brake reminder light is off.

DRIVING TIPS
266
Tires

Ensure that your vehicle's tires are properly inflated.
Adjust the tire pressure to the recommended cold tire
pressure indicated below:
SC400, SC 300 ± Front 220 kPa (2.2 kgf/cm
2 or bar, 32 psi)
Rear 220 kPa (2.2 kgf/cm2 or bar, 32
psi)

The trailer tires should be inflated to the pressure
recommended by the trailer manufacturer in respect to the
total trailer weight.
Trailer lights

Trailer lights must comply with federal, state/provincial
and local regulations. See your local recreational vehicle
dealer or rental agency for the correct type of wiring and
relays for your trailer. Check for correct operation of the
turn signals and stop lights each time you hitch up. Direct
splicing may damage your vehicle's electrical system and
cause a malfunction of your lights.
Break±in schedule

Lexus recommends that you do not tow a trailer with a new
vehicle or a vehicle with any new power train component
(engine, transmission, differential, wheel bearing, etc.) for
the first 800 km (500 miles) of driving.
Maintenance

If you tow a trailer, your vehicle will require more frequent
maintenance due to the additional load. For this
information, please refer to the scheduled maintenance
information in the ºOwner's Manual Supplement/
Maintenance Scheduleº.

Retighten all fixing bolts of the towing ball and bracket
after approximately 1000 km (600 miles) of trailer driving.
Pre±towing safety check

Check that your vehicle remains level when a loaded or
unloaded trailer is hitched. Do not drive if the vehicle has
an abnormal nose±up or nose±down condition, and check
for improper tongue load, overload, worn suspension or
other possible causes.

Make sure the trailer cargo is securely loaded so that it
cannot shift.

Check that your rear view mirrors conform to any federal,
state/provincial or local regulation. If they do not, install
required rear view mirrors appropriate for towing
purposes.

DRIVING TIPS
267
Trailer towing tips
When towing a trailer, your vehicle will handle differ ently
than when not towing. The three main causes of
vehicle±trailer accidents are driver error, excessive speed
and improper trailer loading. Keep these in mind when
towing:

Before starting out, check the operation of the lights and
all vehicle±trailer connections. After driving a short
distance, stop and recheck the lights and connections.
Practice turning, stopping and backing with a trailer in an
area away from traffic until you learn the feel.

Backing with a trailer is difficult and requires practice.
Grip the bottom of the steering wheel and move your hand
to the left to move the trailer to the left. Move your hand
to the right to move the trailer to the right. (This procedure
is generally opposite to that when backing without a
trailer.) Also, just turn the steering wheel a little at a time,
avoiding sharp or prolonged turning. Have someone guide
you when backing to reduce the risk of an accident.

Because stopping distance may be increased,
vehicle±to±vehicle distance should be increased when
towing a trailer. For each 16 km/h (10 mph) of speed,
allow at least one vehicle and trailer length between you
and the vehicle ahead. Avoid sudden braking as you may
skid, resulting in jackknifing and loss of control. This is
especially true on wet or slippery surfaces.

Avoid jerky starts or sudden acceleration.

Avoid jerky steering and sharp turns. The trailer could hit
your vehicle in a tight turn. Slow down before making a
turn to avoid the need of sudden braking.

Remember that when making a turn, the trailer wheels will
be closer than the vehicle wheels to the inside of the turn.
Therefore, compensate for this by making a larger than
normal turning radius with your vehicle.

Crosswinds and rough roads will adversely aff ect handling
of your vehicle and trailer, causing sway. Pay attention to
the rear from time to time to prepare yourself for being
passed by large trucks or buses, which may cause your
vehicle and trailer to sway. If swaying happens, firmly
grip the steering wheel and reduce speed immediately but
gradually. Never increase speed. If it is necessary to
reduce speed, brake slowly. Steer straight ahead. If you
make no extreme correction with the steering or brakes,
your vehicle and trailer will stabilize.

Be careful when passing other vehicles. Passing requires
considerable distance. After passing a vehicle, do not
forget the length of your trailer and be sure you have plenty
of room before changing lanes.

In order to maintain efficient engine braking and electrical
charging performance, do not use overdrive.
Transmission must be in the º4º position (SC400) or in the
º3º position (SC300).

DRIVING TIPS
270
HOW TO SAVE FUEL AND
MAKE YOUR VEHICLE LAST LONGER
Getting more kilometer/mileage from a liter/gallon of fuel is
easy ± just take it easy. It will help make your vehicle last
longer, too. Here are some specific tips on how to save money
on both fuel and repairs:

Keep your tires inflated at the correct pressure. Check
the pressure every two weeks, or at least once a month.
Underinflation causes tire wear and wastes fuel.

Do not carry unneeded weight in your vehicle. Excess
weight puts a heavier load on the engine, causing greater
fuel consumption.

Avoid lengthy warm±up idling. Once the engine is
running smoothly, begin driving ± but gently. Remember,
however, that on cold winter days this may take a little
longer.

Accelerate slowly and smoothly. Avoid jackrabbit starts.

Avoid long engine idling. If you have a long wait and you
are not in traffic, it is better to turn off the engine and start
again later.

Avoid engine overrevving. Use a gear position suitable
for the road on which you are traveling.

Avoid continuous speeding up and slowing down.
Stop±and±go driving wastes fuel.

Avoid unnecessary stopping and braking. Maintain a
steady pace. Try to time the traffic signals so you only
need to stop as little as possible or take advantage of
through streets to avoid traffic lights. Keep a proper
distance from other vehicles to avoid sudden braking. This
will also reduce wear on your brakes.

Avoid heavy traffic or traffic jams whenever possible.

Do not r est your foot on the clutch or brake pedal. This
causes needless wear, overheating and poor fuel economy.

Maintain a m oderate speed on highways. The faster you
drive, the greater the fuel consumption. By reducing your
speed, you will cut down on fuel consumption.

Keep the front wheels in proper alignment. Avoid
hitting the curb and slow down on rough roads. Improper
alignment not only causes faster tire wear but also puts an
extra load on the engine, which, in turn, wastes fuel.

Keep the bottom of your vehicle free from mud, etc.
This not only lessens weight but also helps prevent
corrosion.

Keep your vehicle tuned±up and in top shape. A dirty
air cleaner, improper valve clearance, dirty plugs, dirty oil
and grease, brakes not adjusted, etc. all lower engine
performance and contribute to poor fuel economy. For
longer life of all parts and lower operating costs, keep all
maintenance work on schedule, and if you often drive
under severe conditions, see that your vehicle receives
more frequent maintenance. (For scheduled maintenance
information, please refer to the separate ºOwner's Manual