manual radio set LEXUS SC300 1999 Owners Manual

AIR CONDITIONING AND AUDIO
189
Push the
(SCAN) button for less than 1 seconds. With
ºSCANº on the display, the radio will automatically seek out
a station of higher frequency, hold it for 5 seconds and scan
to the next. To continue listening to the broadcast of your
choice, simply push the
(SCAN) button once again.
Manual tuning: Push the
(TUNE) button briefly. Each
time you push the button, the radio will step up or down to
another frequency.
(c) Presetting a station.
1. Tune in the desired station. (See º(b) Selecting a stationº.)
2. Push one of the station selector buttons and hold it until a
beep is heard. This sets the station to the button and the button
number will appear on the display.
Each button can store one AM station and two FM stations.
To change the preset station to a different one, follow the same
procedure.
The preset station will be cancelled when the power source is
cut off (battery disconnected, blown fuse, etc.).
(d) Adjusting the tone
To adjust the low±pitched tone, push the ºBASSº knob (if
depressed) and turn it.
To adjust the middle±pitched tone, push the ºMIDº knob (if
depressed) and turn it.
To adjust the high±pitched tone, push the ºTREBº knob (if
depressed) and turn it. (e) Adjusting the sound balance
To balance the sound between the right and left speakers, push
the ºBALº knob (if depressed) and turn it.
To balance the sound between the front and rear speakers,
push the ºFADEº knob (if depressed) and turn it.
(f) Automatic sound levelizer
(Except Nakamichi model)
When the audio sound becomes difficult to be heard due to
road noise, wind noise, etc., during driving, push the
(ASL) button. ºASLº appears on the display. The system
adjusts to the optimum volume and tone quality according to
the noise level.

AIR CONDITIONING AND AUDIO
193
*Dolby noise reduction manufactured under license from Dolby
Laboratories Licensing Corporation. ºDOLBYº and the double±D
symbol
are trademarks of Dolby Laboratories Licensing
Corporation.
3. Turn the ºPWR.VOLº knob to adjust the volume.
4. Select your program. (See º(b) Selecting a programº.)
5. Adjust the tone and sound balance. (See º(d) Adjusting the
toneº and º(e) Adjusting the sound balanceº of radio
operation.)
6. If desired, other functions may be used for your
convenience. (See º(c) Other tape player functionsº.)
7. To turn the player off, push the ºPWR.VOLº knob.
8. To eject the cassette, push the
(EJECT) button. As this
is done, the player will turn off. If the radio was on when the
cassette tape was inserted, it will automatically turn on again.
The ignition key can be at any position to eject the cassette.
(b) Selecting a program
1. Push the left side of
(PROG) button to select a
side to play. The tape operation indicator display shows you
which side is being played.
The player will automatically reverse directions at the end of
the tape to play the other side.
2. Play the program you want using either of the following
methods. Manual program selection
Push the
(REW, FF) button on the right side to fast
forward the tape or on the left side to rewind the tape. At this
time, ºFFºor ºREWº will appear on the display. To stop
either fast forwarding or rewinding, push the button on the
same side again or push the
(TAPE) button. The tape
will then resume playing.
ºAutomatic program selectionº button: The automatic
program selection feature allows you to program your
cassette player to skip forward or backward to locate the song
you want to hear. You can skip up to nine programs at a time.
Push
(TRACK) button on the upper side to skip forward.
ºFFº and the number will appear on the display. Push the
button until the number you want to skip appears on the
display. After that, the player will automatically skip
forward.
When the end of the tape is reached, the player automatically
reverses sides and resumes normal play.
Push
(TRACK) button on the lower side to skip backward.
Push the button until ºREWº and the number you want to skip
appear on the display.

If you set ºREW 1º, the player will rewind to the
beginning of the current program.

When counting the number of programs you want to
rewind, remember to count the current program as well.
For example, if you want to rewind to a song that is two
before the song you are listening to, push this button until