fuse chart LEXUS SC400 1991 Service User Guide

CIRCUIT INSPECTION
+B Power Source Circuit
CIRCUIT DESCRIPTION
This is the power source for motors such as the slide motor and reclining mo\
tor.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
Check Door fuse.NG
Check for short in all harness and
components connected to the
DOOR fuse (See attached wiring
diagram).
Check voltage between terminals +B, +B2
and GND of ECU connector. OK
OKProceed to next circuit inspection
shown on matrix chart (See page
BE±276
).
Check continuity between terminal GND
of ECU connector and body ground. NG
NGRepair or replace harness or
connector.
OK
Check and repair harness or connector
between ECU and battery.
WIRING DIAGRAM
BE±284±
BODY ELECTRICAL SYSTEM Power Seat Control System (Driver's Seat)
WhereEverybodyKnowsYourName

OKNG
NGOK
OKNG
INSPECTION PROCEDURE
1Check DOOR fuse.
Check for short in all the harness and components con-
nected to the DOOR fuse (See attached wiring diagram).
2Check voltage between terminals +B, +B2 and GND of ECU connector.
C
OK
PRemove ECU with connectors still connected.
Measure voltage between terminals +B, +B2 and GND
of ECU connector.
Voltage: 10 ± 14 V
Proceed to next circuit inspection shown on matrix chart
(See page BE±276.)
3Check continuity between terminal GND of ECU connector and body ground.
C
OK
Measure resistance between terminal GND of ECU and
body ground.
Resistance: 1
or less.
Repair or replace harness or connector.
Check and repair harness or connector between
ECU and battery.
±
BODY ELECTRICAL SYSTEM Power Seat Control System (Driver's Seat)BE±285
WhereEverybodyKnowsYourName

WIRING DIAGRAM
ECU Power Source Circuit
CIRCUIT DESCRIPTION
This circuit provides power for ECU operation and is also the power source f\
or the sensors.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
Check DOME fuse.NGCheck for short in all the harness
and components connected to
DOME fuse.
(See attached wiring diagram).
OK
Check voltage between terminals SYSB
and SGND of ECU connector. Proceed to next circuit inspection
shown on matrix chart
(See page
BE±276).
Check continuity between terminal SGND
of ECU connector and body ground. OK
NG
OK NG
Replace or repair harness or
connector.
Check and repair harness or connector
between ECU and battery.
BE±286±
BODY ELECTRICAL SYSTEM Power Seat Control System (Driver's Seat)
WhereEverybodyKnowsYourName

OKNG
NGOK
OKNG
INSPECTION PROCEDURE
1Check DOME fuse.
Check for short in all the harness and components con-
nected to the DOME fuse (See attached wiring diagram).
2Check voltage between terminals SYSB and SGND of ECU connector.
C
OK
PRemove ECU with connectors still connected.
Measure voltage between terminals SYSB and SGND
of ECU connector.
Voltage: 10 ± 14 V
Proceed to next circuit inspection shown on matrix chart
(See page BE±276).
3Check continuity between terminal SGND of ECU connector and body ground.\
C
OK
Measure resistance between terminal SGND of ECU
connector and body ground.
Resistance: 1
or less.
Repair or replace harness or connector.
Check and repair harness or connector between
ECU and battery.
±
BODY ELECTRICAL SYSTEM Power Seat Control System (Driver's Seat)BE±287
WhereEverybodyKnowsYourName

WIRING DIAGRAM
Ignition Switch Circuit
CIRCUIT DESCRIPTION
This circuit sends an ignition switch ON or OFF signal to the ECU.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
Check ECU±IG fuse.NG
Check for short in all the harness
and components connected to
ECU±IG fuse.
Check voltage between terminal IG of
ECU connector and body ground. OK
OK
NG Proceed to next circuit inspection
shown on matrix chart
(See page
BE±276).
Check and repair harness or connector
between ECU and battery (See page IN±27).
BE±302±
BODY ELECTRICAL SYSTEM Power Seat Control System (Driver's Seat)
WhereEverybodyKnowsYourName

OKNG
NGOK
INSPECTION PROCEDURE
1Check ECU ± IG fuse.
Check for short in all the harness and components con-
nected to ECU±IG fuse.
2Check voltage between terminal IF of ECU connector and body ground.
C
PRemove ECU with connectors still connected.
Measure voltage between terminal IG of ECU connector
and body ground when ignition switch is on and off.
Ignition switch Voltage
ON
OFF 10 ± 14 V
Below 1 V
Proceed to next circuit inspection shown on matrix chart
(See page BE±276).
Check and repair harness or connector between
ECU and battery (See page IN±27).
±
BODY ELECTRICAL SYSTEM Power Seat Control System (Driver's Seat)BE±303
WhereEverybodyKnowsYourName

WIRING DIAGRAM
CIRCUIT INSPECTION
ECU Power Source Circuit
CIRCUIT DESCRIPTION
This circuit provides power for ECU operation and is also the power source f\
or the slide position sensor.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
Check DOME fuse.NG
OK
NG NG
OK
OK Check for short in all the harness
and components connected to
DOME fuse. (See attached wir-
ing diagram).
Check voltage between terminals SYSB and
GND of ECU connector. Proceed to next circuit inspection
shown on matrix chart.
(See page
BE±319).
Check continuity between terminal GND of
ECU connector and body ground. Repair or replace harness or
connector.
Check and repair harness or connector
between ECU and battery.
BE±324±
BODY ELECTRICAL SYSTEM Power Seat Control System (Passenger's Seat)
WhereEverybodyKnowsYourName

OKNG
NGOK
OKNG
INSPECTION PROCEDURE
1Check DOME fuse.
Check for short in all the harness and components con-
nected to DOME fuse and repair them (See attached wir-
ing diagram).
2Check voltage between terminals SYSB and GND of ECU connector.
C
OK
PRemove ECU with connectors still connected.
Measure voltage between terminals SYSB and GND of
ECU connector.
Voltage: 10 ±14 V
Proceed to next circuit inspection shown on matrix chart
(See page BE±319).
3Check continuity between terminal GND of ECU connector and body ground.
C
OK
Measure resistance between terminal GND of ECU con-
nector and body ground.
Resistance: 1
or less
Repair or replace harness or connector.
Check and repair harness or connector between
ECU and battery.
±
BODY ELECTRICAL SYSTEM Power Seat Control System (Passenger's Seat)BE±325
WhereEverybodyKnowsYourName

Check DOOR fuse.NG
OK
NG
OK NGOK Check for short in all the harness
and components connected to
the DOOR fuse (See attached
wiring diagram). *
1
Check voltage between terminals +B and
GND of ECU connector.
Proceed to next circuit inspection
shown on matrix chart (See page
BE±319
).
Check continuity between terminal GND of
ECU connector and body ground. Repair or replace harness of
connector.
Check and repair harness or connector
between ECU and battery. *
1The power source is supplied to the actuator
(Slide motor) through the passenger's seat
ECU accordingly, if a short circuit of the W/H
or actuator occurs in the actuator circuit, the
DOOR fuse may become open, so also in-
spect the actuator. (Slide motor circuit on
page
BE±328 ).
WIRING DIAGRAM
Slide Motor Power Source Circuit
CIRCUIT DESCRIPTION
This is the power source for slide motor.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
BE±326±
BODY ELECTRICAL SYSTEM Power Seat Control System (Passenger's Seat)
WhereEverybodyKnowsYourName

OKNG
NGOK
OKNG
INSPECTION PROCEDURE
1Check DOOR fuse.
Check for short in all the harness components con-
nected to the DOOR fuse and repair them (See attached
wiring diagram). *1
2Check voltage between terminals +B and GND of ECU connector.
C
OK
PRemove passenger's seat ECU with connectors still
connected.
Measure voltage between terminals +B and GND of
ECU connector.
Voltage: 10 ± 14 V
Proceed to next circuit inspection shown on matrix chart
(See page BE±319).
3Check continuity between terminal GND of ECU connector and body ground.
C
OK
Measure resistance between terminal GND of ECU and
body ground.
Resistance: 1
or less
Repair or replace harness or connector.
Check and repair harness or connector between
ECU and battery.
±
BODY ELECTRICAL SYSTEM Power Seat Control System (Passenger's Seat)BE±327
WhereEverybodyKnowsYourName