light LEXUS SC400 1991 Service Owner's Manual

4
5
6
Check terminal LA of center airbag sensor assem-
bly and electrical connection check mechanism.
If normal, replace center airbag sensor assembly.
NG
OK
(1) Disconnect negative (±) terminal cable from battery.
(2) Connect center airbag sensor assembly.
(3) Connect negative (±) terminal cable to battery.
(4) Turn ignition switch ACC or ON. Voltage: 10±14 V
Check operation of airbag warning light.
(1) Disconnect center airbag sensor assembly.
(2) Connect negative (±) terminal cable to battery.
(3) Turn ignition switch ACC or ON.
Measure voltage LA terminal of harness side
connector of center airbag sensor assembly.
Repair airbag warning light circuit
(see page BE±150).
NG
Using simulation method, reproduce
malfunction symptoms (See page In±20).NG
OK
Check airbag warning light circuit.
Does airbag warning light come on?
Is new ECU±B fuse burnt out again?
From the results of the above inspection, the malfunctioning part can now be considered norm\
al. To
make sure of this, use the simulation method to check.
Check harness between ECU±B fuse and airbag warning light, and ECU±B fus\
e and center airbag sensor
assembly.
AB±78±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName

OK
Check operation of airbag warning light.
NG1
WIRING DIAGRAM
2Is diagnostic code 41 output again? System is normal.
Check harness between ECU±B
fuse and center airbag sensor as-
sembly. If normal, replace center
airbag sensor assembly.
Perform troubleshooting according to
malfunction code output. NO
YES
Diag. Code 41Malfunction Stored in Memory
CIRCUIT DESCRIPTION
If a malfunction occurs in the airbag system, malfunction codes 11 to 31 may be output, and when the
battery is disconnected after the malfunction is repaired, malfunction codes 11 to 31 will be cleared,
but code 41 will be output instead.
So long as the cancellation operation for a malfunction stored in memory (\
See page
AB±32) is not per-
formed, code 41 is stored in the center airbag sensor assembly and the airbag w\
arning light remains
lit up.
Code No.Diagnosis
41
Malfunction recorded in memory.41
Center airbag sensor assembly malfunction.
DIAGNOSTIC CHART
AB±82±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName

Clear malfunction code 41 stored in memory
(See page AB±32).
Check operation of airbag warning light.
NG
OK
1
Airbag warning light turns off.
(1) Turn ignition switch LOCK, and wait at least
2 seconds.
(2) Turn ignition switch ACC or ON, and wait at least 20 seconds.
(3) Check operation of airbag warning light.
System is normal.
2Is diagnostic code 41 output again?
(1) Turn ignition switch ACC or ON, and wait at least 20 seconds.
(2) Using SST, connect terminals Tc and E
1 of TDCL.
SST 09843±18020
(3) Check diagnostic code.
Check harness between ECU±B fuse and center
airbag sensor assembly. If normal, replace
center airbag sensor assembly.
Perform troubleshooting according to malfunction code output.
NG
OK
INSPECTION PROCEDURE
±
SRS AIRBAG TroubleshootingAB±83
WhereEverybodyKnowsYourName

YES
Does airbag warning light turn off?
NO
1
Replace center airbag sensor assembly. Check airbag warning light circuit
or terminal AB circuit of TDCL or
check connector.
WIRING DIAGRAM
Airbag Warning Light System (Always Lit Up)
CIRCUIT DESCRIPTION
The airbag warning light is located on the combination meter.
When the airbag system is normal, the airbag warning light lights up for\
approx. 6 seconds after the
ignition switch is turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the airbag system, the airbag warning light\
lights up to inform the driver of
the abnormality.
When terminals Tc and E of the TDCL are connected, the diagnostic code is displayed by t\
he blinking
of the airbag warning light.
DIAGNOSTIC CHART
AB±84±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName

1
(1) Turn ignition switch LOCK.
(2) Disconnect negative (±) terminal cable frombattery.
(3) Disconnect center airbag sensor assembly connector.
(4) Connect negative (±) terminal cable to battery.
Does airbag warning light turn off?
Check airbag warning light circuit or terminal
AB circuit of TDCL or check connector.NG
YES
Check operation of airbag warning light.
Replace center airbag sensor assembly.
INSPECTION PROCEDURE
±
SRS AIRBAG TroubleshootingAB±85
WhereEverybodyKnowsYourName

NG
Check voltage between terminals Tc and E
1of TDCL or check connector.
OK1
2
3
1
NG
NG
NG OK
OK
OK
3
Check voltage between terminal Tc of TDCL
or check connector and body ground.Check center airbag sensor assembly.
Replace center airbag sensor assemly.
Check resistance between terminal Tc of
center airbag sensor assembly and body
ground.
HINT: If the diagnostic code is continuously displayed, perform the following \
troubleshooting:
Repair or replace harnes or connector. Replace center airbag sensor
assembly.
Check harness between center
airbag sensor assembly and
TDCL or check connector.
Check harness between terminal
E1 of TDCL or check connector
and body ground.
Go to step
Tc Terminal Circuit
CIRCUIT DESCRIPTION
By connecting terminals Tc and E of the TDCL or check connector, the center airbag sensor assembly
is set in the diagnostic code output mode. The diagnostic codes are disp\
layed by the blinking of the
airbag warning light.
DIAGNOSTIC CHART
Troubleshooting
for this system is dif ferent depending on whether the diagnostic code is not displayed
or is continuously displayed. Confirm the problem symptoms first before se\
lecting the appropriate
troubleshooting procedure.
HINT: If the diagnostic code is not displayed, perform the following trouble\
shooting:
AB±86
±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName

NGOK
Check center airbag sensor assembly.3
(1) Disconnect negative (±) terminal cable from
battery, and wait at least 20 seconds.
(2) Turn ignition switch lock.
(3) Disconnect center airbag sensor assembly
connector.
(4) Using a service wire, connector terminal Tc of center airbag sensor assembly connector to
body ground.
(5) Install the center airbag sensor assembly.
(6) Connect negative (±) terminal cable to battery.
(7) Turn ignition switch ACC or ON.
Check operation of airbag warning light.
Airbag light comes on.
Check harness between center airbag sensor
assembly and TDCL or check connector.
Replace center airbag sensor assembly.
C
P
OK
CautionNever turn ignition switch ACC or ON and
never connect negative (±) terminal to battery
before the center airbag sensor assembly is
installed.
±
SRS AIRBAG TroubleshootingAB±89
WhereEverybodyKnowsYourName

2. CONFIRM FUNCTIONING OF SST (See page AB±97)
SST 09082±00700
3. INSTALL SST CAUTION: Check that there is no looseness in the
steering wheel and steering wheel pad.
(a) Remove the No. 1 under cover.
(b) Disconnect the airbag connector of the spiral cable.
(c) Connect the SST connector to the airbag connector ofthe spiral cable.
SST 09082±00700
(d) Move the SST to at least 10 m (33 ft) from the front of the
vehicle.
(e) Close all the doors and windows of the vehicle.
NOTICE: Take care not to damage the SST wire harness.
(f) Connect the SST red clip to the battery positive (+) terminal and the black clip to the battery negative (±)
terminal.
4. DEPLOY AIRBAG (a) Confirm that no±one is inside the vehicle or within 10 (33 ft) of the vehicle.
(b) Press the SST activation switch and deploy the airbag.
HINT: The airbag deploys simultaneously as the LED of the
SST activation switch lights up.
AB±92
±
SRS AIRBAG Disposal of Steering Wheel Pad (with Airbag)
WhereEverybodyKnowsYourName

(Covering Method Using Tires)
Place at least three tires without disc wheel on top of the disc
wheel with tire to which the steering wheel pad is tied.
Tire size: Must exceed the following dimensions ±Width 185 mm (7.28 in.)
Inner diam 360 mm (14.17 in.)
CAUTION: Do not use tires with disc wheels.
NOTICE: The tires may be marked by the airbag deploy-
ment, so use redundent tires.
7. AIRBAG DEPLOYMENT (a) Connect the SST red clip to the battery positive (+)terminal and the black clip to the battery negative (±)
terminal.
(b) Confirm that no±one is within 10 m (33 ft) of the disc wheel the steering wheel pad is tied to.
(c) Press the SST activation switch and deploy the airbag.
HINT: The airbag deploys simultaneously as the LED of the
SST activation switch lights up.
8. DISPOSAL OF STEERING WHEEL PAD (WITH AIRBAG) CAUTION:
w The steering wheel pad is very hot when the airbag is
deployed, so leave it alone for at least 30 minutes after de-
ployment.
w Use gloves and safety glasses when handling a steering
wheel pad with deployed airbag.
w Do not apply water, etc. to a steering wheel pad with
deployed airbag.
w Always wash your hands with water after completing the
operation.
(a) Remove the steering wheel pad from the disc wheel.
(b) Place the steering wheel pad in a vinyl bag, tie the end
tightly and dispose of it the same way as other general
parts.
AB±96
±
SRS AIRBAG Disposal of Steering Wheel Pad (with Aribag)
WhereEverybodyKnowsYourName

CONFIRM FUNCTIONING OF SST
When deploying the airbag, always use the specified SST:
SRS AIRBAG DEPLOYMENT TOOL.
SST 09082±00700
1. CONNECT SST TO BATTERY Connect the red clip of the SST to the battery positive (+) ter-
minal and the black clip to the battery negative (±) terminal.
HINT: Do not connect the yellow connector which connects
with the airbag system.
2. CONFIRM FUNCTIONING OF SST Press the SST activation switch, and confirm the LED of the
SST activation switch lights up.
CAUTION: If the LED lights up when the activation switch
is not being pressed, SST malfunction is probable, so
definitely do not use the SST.
±
SRS AIRBAG Disposal of Steering Wheel Pad (with Aribag)AB±97
WhereEverybodyKnowsYourName