lock LEXUS SC400 1991 Service Owner's Manual

8. PULL FLOOR CARPET DOWN AND REMOVECOMPUTER COVER
9. REMOVE EVAPORATOR COVER AND FOOT AIR DUCT BOLT
10. REMOVE EVAPORATOR (a) Remove six bolts and down the lower case.
(b) Pull and remove the evaporator.
(c) Pull out the evaporator sensor from the evaporator fins.
(d) Remove two bolts using a hexagon wrench and separate the evaporator and expansion valve.
INSPECTION OF EVAPORATOR
1. INSPECT FINS FOR BLOCKAGE
If the fins are clogged, clean them with compressed air.
NOTICE: Never use water to clean the evaporator.
2. INSPECT FITTINGS FOR CRACKS OR SCRATCHES Repair as necessary.
±
AIR CONDITIONING SYSTEM EvaporatorAC±123
WhereEverybodyKnowsYourName

HEATER RADIATOR
REMOVAL OF HEATER RADIATOR
1. SET TEMPERATURE CONTROL SWITCH TO MAX COOL
2. REMOVE A/C UNITSee page AC±107
3. REMOVE HATER RADIATOR
(a) Remove the two screws and the plate.
(b) Remove the two screws and the clamps.
(c) Pull the radiator out.
INSPECTION OF HEATER RADIATOR
INSPECT FINS FOR BLOCKAGE If the fins are clogged, clean them with compressed air.
INSTALLATION OF HEATER RADIATOR
1. INSTALL HEATER RADIATOR TO A/C UNIT(a) Put the radiator in the A/C until.
(b) Install the clamps with two screws.
(c) Install the plate with two screws.
2. INSTALL A/C UNIT
See page AC±108
±
AIR CONDITIONING SYSTEM Heater RadiatorAC±125
WhereEverybodyKnowsYourName

WATER TEMPERATURE SENSOR
REMOVAL OF WATER TEMPERATURE
SENSOR
1. REMOVE A/C UNITSee page AC±107
2. REMOVE SENSOR After taking off the clamp, take out the sensor.
INSPECTION OF WATER TEMPERATURE
SENSOR
See page AC±51
INSTALLATION OF WATER
TEMPERATURE SENSOR
1. INSTALL SENSOR TO A/C UNIT
Install the sensor with the clamp.
2. INSTALL A/C UNIT See page AC±108
PRESSURE SWITCH
INSPECTION OF PRESSURE SWITCH
See page AC±57
REMOVAL OF PRESSURE SWITCH
1. RECOVER REFRIGERANT IN REFRIGERANT SYSTEM
See page AC±16
2. REMOVE PRESSURE SWITCH
(a) Disconnect the connector.
(b) Remove the pressure switch from the liquid tube. HINT: Lock the switch mount on the tube with an open end
wrench, being careful not to deform the tube, and remove the
switch.
AC±136
±
AIR CONDITIONING SYSTEM Water Temperature Sensor, Pressure Switch
WhereEverybodyKnowsYourName

INSTALLATION OF PRESSURE SWITCH
1. INSTALL PRESSURE SWITCH
(a) Install the pressure switch to the liquid tube.
Specified torque: 10 NVm (100 kgf Vcm, 7 ft Vlbf)
HINT: Lock the switch mount on the tube with an open end
wrench, being careful not to deform the tube, and install the
switch.
(b) Connect the connector.
2. EVACUATE AIR IN REFRIGERATION SYSTEM AND CHARGE WITH REFRIGERANT
See page AC±17
Specified amount: 950 + 50 g (33.44 + 1.76 oz)
3. INSPECTION FOR LEAKAGE OF REFRIGERANT
Using a gas lead tester, check for leakage of refrigerant from
the pressure switch mount.
4. INSPECT A/C OPERATION
POWER TRANSISTOR
REMOVAL OF POWER TRANSISTOR
1. REMOVE GLOVE BOX
2. REMOVE POWER TRANSISTOR
(a) Disconnect connectors.
(b) Remove the two screws and the power transistor.
INSPECTION OF POWER TRANSISTOR
See page AC±79
INSTALLATION OF POWER
TRANSISTOR
1. INSTALL POWER TRANSISTOR
(a) Install power transistor with two screws.
(b) Connect connectors.
2. INSTALL GLOVE BOX
See page BO±112
±
AIR CONDITIONING SYSTEM Pressure Switch, Power TransistorAC±137
WhereEverybodyKnowsYourName

INSTALLATION OF PRESSURE SWITCH
1. INSTALL PRESSURE SWITCH
(a) Install the pressure switch to the liquid tube.
Specified torque: 10 NVm (100 kgf Vcm, 7 ft Vlbf)
HINT: Lock the switch mount on the tube with an open end
wrench, being careful not to deform the tube, and install the
switch.
(b) Connect the connector.
2. EVACUATE AIR IN REFRIGERATION SYSTEM AND CHARGE WITH REFRIGERANT
See page AC±17
Specified amount: 950 + 50 g (33.44 + 1.76 oz)
3. INSPECTION FOR LEAKAGE OF REFRIGERANT
Using a gas lead tester, check for leakage of refrigerant from
the pressure switch mount.
4. INSPECT A/C OPERATION
POWER TRANSISTOR
REMOVAL OF POWER TRANSISTOR
1. REMOVE GLOVE BOX
2. REMOVE POWER TRANSISTOR
(a) Disconnect connectors.
(b) Remove the two screws and the power transistor.
INSPECTION OF POWER TRANSISTOR
See page AC±79
INSTALLATION OF POWER
TRANSISTOR
1. INSTALL POWER TRANSISTOR
(a) Install power transistor with two screws.
(b) Connect connectors.
2. INSTALL GLOVE BOX
See page BO±112
±
AIR CONDITIONING SYSTEM Pressure Switch, Power TransistorAC±137
WhereEverybodyKnowsYourName

Check center airbag sensor assembly.
Diagnostic code 14 is not output.(1) Connect connector to center airbag sensor
connector.
(2) Connect connector between center airbag sensor assembly and spiral cable.
(3) Using a service wire, connect D+ and D± on spiral cable side of connector between spiral
cable and steering wheel pad.
(4) Connect negative (±) terminal cable to battery,
and wait at least 2 seconds.
Check squib.
(1) Turn ignition switch ACC or ON, and wait at least 20 seconds.
(2) Using SST, connect terminals Tc and E1 of TDCL.
SST 09843±18020
(3) Check diagnostic code.
(1) Turn ignition switch LOCK.
(2) Disconnect battery negative (±) terminal cable, and wait at least 20 seconds.
(3) Connect steering wheel pad (squib) connector.
(4) Connect negative (±) terminal cable to battery, and wait at least 2 seconds.
Diagnostic code 14 is not output. (1) Turn ignition switch ACC or ON, and wait at least 20 seconds.
(2) UsingSST, connect terminals Tc and E1 of TDCL.
SST 09843±18020
(3) Check diagnostic code. Codes other than code 14 may be output at this
time, but this is not relevant to this check
Codes other than code 14 may be output at this
time, but this is not relevant to this check Replace steering wheel pad.
From the results of the above inspection, the malfunctioning part can no\
w be considered normal.
To make sure this, use the simulation method to check. Replace center airbag sensor assembly.
AB±66±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName

 
Diag. Code 15\
 \
Open in Front Airbag Sensor Circuit
CIRCUIT DESCRIPTION
The front airbag sensor detects the deceleration force in a frontal collisi\
on and is located in the front fender
on the left and right sides.
For details of the function of each component, see FUNCTION OF COMPONENT\
S on page AB±5.
Diagnostic code 15 is recorded when an open is detected in the front air\
bag sensor circuit.
NOTICE: The front airbag sensor connector is equipped with an electrical connection \
check mechanism
for the purpose of detecting an open in the front airbag sensor (See page AB±7). This mechanism is
constructed so that when the terminals of the front airbag sensor have been connect\
ed (when the connec-
tor housing lock is in the locked condition), the connection detection \
pin on the wire harness side connects
with the terminals for diagnosis use on the sensor side. If the connector is\
not properly connected, the diag-
nosis system may detect only a malfunction code, even though the airbag syste\
m is functioning normally.
When connecting the front airbag sensor connector, make sure it is connected properly. If diagnostic code
15 is displayed after the front airbag sensor connector has been connect\
ed, check again that it is properly
connected.
 

Code No.
\
 
\

\
Diagnosis
 




15
\
 
\


\

\



Open circuit in +S wire harness or ±S wire harness of front airbag s\
ensor.

Front airbag sensor malfunction.

Malfunction of electrical connection check mechanism of front airbag se\
nsor.

Center airbag sensor assembly malfunction.
AB±68±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName

Diag. Code 22Airbag Warning Light System Malfunction
CIRCUIT DESCRIPTION
The airbag warning light is located on the combination meter.
When the airbag system is normal, the airbag warning light lights up for\
approx. 6 seconds after the
ignition switch is turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the airbag system, the airbag warning light\
lights up to inform the driver of
the abnormality.
When terminals Tc and E of the TDCL are connected, the diagnostic code is displayed by t\
he blinking
of the airbag warning light.
The airbag warning light circuit is equipped with an electrical connecti\
on check mechanism which
detects when the connector to the center airbag sensor assembly is not p\
roperly connected.
If the connector to the center airbag sensor assembly is not properly co\
nnected, the airbag warning
light will not light up.
Diagnostic code 22 is recorded when a malfunction occurs in the airbag w\
arning light system.
If an OPEN malfunction occurs in the airbag warning light system, the ai\
rbag warning light does not
light up, so that until the malfunction is repaired, the diagnostic code\
s (including code 22) cannot be
confirmed.
Code No.Diagnosis
22
Open circuit in airbag warning light system.22
Center airbag sensor assembly malfunction.
AB±74±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName

1
Using simulation method, reproduce malfunction
symptoms (See page IN±20).NO
YES
(1) Turn ignition switch LOCK, and wait at least 2
seconds.
(2) Turn ignition switch ACC or ON, and wait at least 20 seconds.
(3) Using SST, connect terminals Tc and E
1 of TDCL.
SST 09843±18020
(4) Check diagnostic code. Clear malfunction code 41 stored in memory
(See page
AB±35).
Is diagnostic code 22 output again?
Replace center airbag sensor assembly.
HINT: If diagnostic code 22 is output, perform the following troubleshooting\
:
±
SRS AIRBAG TroubleshootingAB±79
WhereEverybodyKnowsYourName

1
NG
OK
(1) Turn ignition switch LOCK, and wait at least 20
seconds.
(2) Turn ignition switch ACC or ON, and wait at least 20 seconds.
(3) Repeat operation in step (1) and (2) at least 5 times.
(4) Using SST, connect terminals Tc and E
1 of TDCL.
SST 09843±18020
(5) Check diagnostic code.
Is diagnostic code 31 output again?
Using simulation method, reproduce
malfunction symptoms (See page IN±20).
Clear malfunction code stored in memory
(See page
AB±32).
Replace center airbag sensor assembly.
INSPECTION PROCEDURE
HINT:When a malfunction code other than code 31 is displayed at the same time, fi\
rst repair the malfunction indicated by the malfunction code other than code 31.
±
SRS AIRBAG TroubleshootingAB±81
WhereEverybodyKnowsYourName