traction control LEXUS SC400 1991 Service Manual Online

 



Symbols
(Terminals No.) 


STD Voltage (V)\
 
\

\

Condition
 LBL
(A25±6)  ± GND
(A25±22) 10±14\
 \
IG switch ON
Fluid in M/C reservoir tank above MIN level.
 

STP
 

±
 

GND
 

Below 1.5\
 
\

\
Stop light switch OFF 


STP
(A25±10) 
± 


GND
(A25±22) 

8±14
\
 
\

\
Stop light switch ON
 D/G
(A25±20) ± GND
(A25±22) 10±14\
 \
IG switch ON, ABS warning light OFF
 

Tc
(A26±3)
 

±
 

GND
(A25±22)
 

10±14
\
 
\

\
IG switch ON
 

Ts
(A26±1) 

±
 

GND
(A25±22) 

10±14
\
 
\

\
IG switch ON
 P 
±
 GND 10±14\
 \
IG switch ON, Shift position in ªPº position P
(A26±10) ± GND
(A25±22) Below 1.5\
 \
IG switch ON, Other shift position in ªPº position 

N
 

±
 

GND
 

10±14\
 
\

\
IG switch ON, Shift position in ªNº position
 
N
(A26±5) 
±
 
GND
(A25±22) Below 1.5\
 \
IG switch ON, Other shift position in ªNº position
 

FR+
(A24±17) ± 

FR±
(A24±4) 

AC generation\
 
\

IG switch ON
Slowly turn right front wheel.
 

FL+
(A24±5)
 

±
 

FL±
(A24±18)
 

AC generation
\
 
\

\
IG switch ON
Slowly turn left front wheel.
 

RR+
(A25±14) 

±
 

RR±
(A25±3) 

AC generation
\
 
\

\
IG switch ON
Slowly turn right rear wheel.
 

RL+
(A25±4) 

±
 

RL±
(A25±15) 

AC generation
\
 
\

\
IG switch ON
Slowly turn left rear wheel.
 


FRO
(A26±15) 
± 


GND
(A25±22) 

Pulse generation\
 
\

\

IG switch ON
Slowly turn right front wheel.
 


FLO
(A26±6) 
± 


GND
(A25±22) 

Pulse generation\
 
\

\

IG switch ON
Slowly turn left front wheel.
 


RRO
(A26±13) 
± 


GND
(A25±22) 


Pulse generation\
 
\

\

IG switch ON
Slowly turn right rear wheel.
 RLO
(A26±4) ± GND
(A25±22) Pulse generation\
 \
IG switch ON
Slowly turn left rear wheel.
±
BRAKE SYSTEM TRACTION CONTROL SYSTEM (TRAC)BR±159
WhereEverybodyKnowsYourName

TRAC ECU:
 

Symbols
(Terminals No.) 

STD Voltage (V)
\
 
\

\
Condition
 

BAT
(T13±8) 

±
 

GND
(T14±14) 

10±14
\
 
\

\
Always
 


BM
(T14±15) 
± 


GND
(T14±14) 

10±14\
 
\

\
Always
 


IG
(T14±2) 
± 


GND
(T14±14) 

10±14\
 
\

\
IG switch ON
 


ACM
(T14±13) 
± 


GND
(T14±14) 


4±5\
 
\

\

IG switch ON
Sub throttle valve fully open
 A
(T14±11) ± GND
(T14±14) 4±5\
 \
IG switch ON
Sub throttle valve fully open
 

A
(T14±12) 

±
 

GND
(T14±14) 

4±5
\
 
\

\
IG switch ON
Sub throttle valve fully open
 

BCM
(T14±26) 

±
 

GND
(T14±14) 

4±5
\
 
\

\
IG switch ON
Sub throttle valve fully open
 


B
(T14±24) 

±
 


GND
(T14±14) 

4±5
\
 
\

\

IG switch ON
Sub throttle valve fully open
 


B
(T14±25) 
± 


GND
(T14±14) 

4±5\
 
\

\

IG switch ON
Sub throttle valve fully open
 TR5 ± E1 Below 1.0\
 \
IG switch ON, Engine stopped
 
TR5
(T14±16) ± 
E1
(T14±20) 10±14\
 \
Engine idling
 IDL1 
±
 E1 Below 1.0\
 \
Engine idling, Main throttle valve fully closed
 IDL1
(T14±10) ± E1
(T14±20) 10±14\
 \
Engine idling, Main throttle valve fully open 
IDL2
 
±
 
E1
 Below 1.0\
 \
IG switch ON, Sub±throttle valve fully closed 


IDL2
(T14±22) 
± 


E1
(T14±20) 

10±14\
 
\

\
IG switch ON, Sub±throttle valve fully open
 VTH ± E1 Below 1.5\
 \
IG switch ON, Main throttle valve fully closed
 
VTH
(T14±8) 
±
 
E1
(T14±20) 3.0±5.5\
 \
IG switch ON, Main throttle valve fully open
 VSH ± E1 Below 1.5\
 \
IG switch ON, Sub±throttle valve fully closed
 
VSH
(T14±19) ± 
E1
(T14±20) 3.0±5.5\
 \
IG switch ON, Sub±throttle valve fully open
 


TR2
(T14±21) 
± 


E1
(T14±20) 

10±14\
 
\

\
IG switch ON
 


NEO
(T14±6) 
± 


E1
(T14±20) 

Pulse generation\
 
\

\
Engine idling
 CSW ± GND Below 1.5\
 \
IG switch ON, TRAC cut switch pushed in
 
CSW
(T13±13)  ± 
GND
(T14±14) 10±14\
 \
IG switch ON, TRAC cut switch released
    
Below 1 5
\
 \
IG switch ON, PKB switch ON,
 PKB 
±
 GND
(T14±14)
 Below 1.5\
 \
Fluid in M/C reservoir above MIN level
 PKB
(T14±1) ± (T14±14) 
10±14
\
 \
IG switch ON, PKB switch OFF,    10±14\
 \
Fluid M/C reservoir above MIN level
BR±160±
BRAKE SYSTEM TRACTION CONTROL SYSTEM (TRAC)
WhereEverybodyKnowsYourName

 



Symbols
(Terminals No.) 


STD Voltage (V)\
 
\

\

Condition
 IND
(T13±11) ± GND
(T14±14) 10±14\
 \
IG switch ON, TRAC indicator light OFF
 

WT
 

±
 

GND
 

Below 2.0\
 
\

\
IG switch ON, TRAC OFF indicator light ON 


WT
(T13±14) 
± 


GND
(T14±14) 

10±14
\
 
\

\
IG switch ON, TRAC OFF indicator light OFF
 STP ± GND Below 1.5\
 \
Stop light switch OFF
 
STP
(T13±2) ± 
GND
(T14±14) 8±14\
 \
Stop light switch ON
 P 
±
 GND 10±14\
 \
IG switch ON, Shift position in ªPº position
 
P
(T13±7) ± 
GND
(T14±14) Below 1.5\
 \
IG switch ON, Other shift position in ªPº position
 N 
±
 GND 10±14\
 \
IG switch ON, Shift position in ªNº position
 N
(T13±16) ± GND
(T14±14) Below 1.5\
 \
IG switch ON, Other shift position in ªNº position 

Tc
(T13±6) 

±
 

GND
(T14±14) 

10±14
\
 
\

\
IG switch ON
 

FRO
(T13±10) 

±
 

GND
(T14±14) 

Pulse generation
\
 
\

\
IG switch ON
Slowly turn right front wheel
 


FLO
(T13±3) 
± 


GND
(T14±14) 

Pulse generation\
 
\

\

IG switch ON
Slowly turn left front wheel
 


RRO
(T13±12) 
± 


GND
(T14±14) 

Pulse generation\
 
\

\

IG switch ON
Slowly turn right rear wheel
 


RLO
(T13±5) 
± 


GND
(T14±14) 


Pulse generation\
 
\

\

IG switch ON
Slowly turn left rear wheel
±
BRAKE SYSTEM TRACTION CONTROL SYSTEM (TRAC)BR±161
WhereEverybodyKnowsYourName

Shift Lock ECU
Tilt and Power
Telescopic ECU
Airbag ECU
Cruise Control ECU Engine ECUABS and Traction ECU
(w/ Traction System) or
ABS ECU
(w/o Traction System)
Theft Deterrent and
Door Lock ECU
(w/ Traction System)
Traction ECU
Remote Control Mirror ECU A/C Control Amplifier
PPS ECU
Engine Cooling Fan ECU
Component to be aligned
Section of repair manual
for relevant model year
Front Wheels Suspension and Axle (SA) section
Rear Wheels Suspension and Axle (SA) section
Propeller Shaft Propeller Shaft (PR) section
2. BRAKE SYSTEM
The brake system is one of the most important safety components. Always \
follow the directions and
notes given in section BR of the repair manual for the relevant model ye\
ar when handling brake sys-
tem parts.
NOTICE: When repairing the brake master cylinder or TRAC system, bleed t\
he air out of the TRAC
system.
3. DRIVE TRAIN AND CHASSIS
The drive train and chassis are components that can have great effects on the running performance
and vibration resistance of the vehicle. After installing components in \
the sections listed in the table
below, perform alignments to ensure correct mounting angles and dimensions. P\
articularly accurate
repair of the body must also be done to ensure correct alignment.
HINT: Correct procedures and special tools are required for alignment. Alway\
s follow the directionsgiven in the repair manual for the relevant model year during alignment \
and section DI of this manual.
4. ECU (ELECTRONIC CONTROL UNIT)
Locations of ECUs
INTRODUCTIONIN-8
WhereEverybodyKnowsYourName

Coolant which is heated in the water jacket is pumped to the radiator, through which a cooling fan blows
air to cool the coolant as it passes through. Coolant which has been coo\
led is then sent back to the engine by
the water pump, where it cools the engine. The water jacket is a network of channels in the shell of the cylinder bloc\
k and cylinderhead through which
coolant passes. It is designed to provide adequate cooling through the cylinders and combus\
tion chambers
which become heated during engine operation.
RADIATOR The radiator performs the function of cooling the coolant which has pass\
ed through the waterjacket and
become hot, and it is mounted in the front of the vehicle. The radiator consis\
ts of an upper tank and lower tank,
and a core which connects the two tanks. The upper tank contains the inlet \
for coolant from the water jacket
and the filler inlet. It also has a hose attached through which excess cool\
ant or steam can flow. The lower tank
contains the outlet for coolant and drain plug. The core contains many t\
ubes through which coolant flows from
the upper tank to the lower tank as well as cooling fins which radiate heat\
away from the coolant in the tubes.
The air sucked through the radiator by the cooling fan, as well as the wind generated by the ve\
hicle's travel,
passes through the radiator, cooling the coolant. Models with automatic transmission include an aut\
omatic
transmission fluid cooler built into the lower tank of the radiator. A cooling fan is mounted behind radiator to assist
the flow of air through the radiator. When the coolant temperature is low, the fan operates slowly to help the warm
up, and when the coolant temperature becomes high, the fan speed is increas\
ed to provide the air flow required
for cooling.
RADIATOR CAP (on Reservoir Tank)
The radiator cap is a pressure type cap which seals the radiator, resulting in pressurization of the radiator
as the coolant expands. The pressurization prevents the coolant from boi\
ling even when the coolant tempera-
ture exceeds 100 5C (212 5F). A relief valve (pressurization valve) and a vacuum valve (negati\
ve pressure valve)
are built into the radiator cap. The relief valve opens and lets steam esca\
pe through the overflow pipe when
the pressure generated inside the cooling system exceeds the limit (coolant temperature: 110±120 5C
(230±248 5F) pressure; 29.4±98.1 kPa (0.3±1.0 kgf/cm2, 4.3±14.2 psi)). The vacuum v\
alve opens to alleviate
the vacuum which develops in the coolant system after the engine is stopped\
and the coolant temperature
drops.
RESERVOIR TANK The purpose of the reservoir tank is to catch coolant overflows created by \
volumetrix expansion when the
coolant temperature increases. The cap of the reservoir tank is a pressure type\
which prevents deterioration
of the LLC (Long Life Coolant) caused by contact with atmospheric air, increases vaporization performance and
reduces loss of the coolant volume.
WATER PUMP The water pump is mounted on the front of the cylinder block and driven by t\
he reverse side of the timing
belt.
THERMOSTAT The thermostat has a wax type by±pass valve and is mounted in the wat\
er inlet housing. The thermostat
begins to open at the temperature of 80 5C (180 5F). When the coolant temperature is low, the valve closes to
prevent coolant flow to the radiator, thus permitting the engine to warm up rapidly. When the by±pass valve
opens the by±pass circuit, the engine coolant continues to circulate \
inside the engine, quickly and uniformly
warming up to the appropriate temperature. When the coolant temperature is high\
, the valve opens and coolant
flows to the radiator where it is cooled. When the wax inside the thermostat \
is heated, it expands and thus
creates pressure which overpowers the force of the spring which keeps the valve\
closed. When the wax cools,
its contraction causes the force of the spring to take effect once more, closing the valve.
ELECTRONICALLY CONTROLLED HYDRAULIC COOLING FAN (See page CO±22)
±
COOLIING SYSTEM DescriptionCO±3
WhereEverybodyKnowsYourName

Diag. Code 41, 47(Sub±) Throttle Position Sensor Circuit
CIRCUIT DESCRIPTION
The throttle position sensor is mounted in the throttle body
and detects the throttle valve opening angle. When the
throttle valve is fully closed, the IDL contacts in the throttle
position sensor are on, so the voltage at the terminal IDL of
the ECU become 0 V. At this time, a voltage of approximately
0.7 V is applied to the terminal VTA of the ECU. When the
throttle valve is opened, the IDL contacts go off and thus the
power source voltage of approximately 12 V in the ECU is ap-
plied to the terminal IDL of the ECU. The voltage applied to
the terminal VTA of the ECU increases in proportion to the
opening angle of the throttle valve and becomes approxi-
mately 3.5±5.0 V when the throttle valve is fully opened. The
ECU judges the vehicle driving conditions from these signals
input from the terminals VTA and IDL, and uses them as one
of the conditions for deciding the air±fuel ratio correction,
power increase correction and fuel±cut control etc. The sub±
throttle position sensor is built and operates in the same way
as the main throttle position sensor. This sensor is used for
traction control. The sub±throttle valve is opened and closed
by the sub±throttle actuator according to signals from the
TRAC ECU to control the engine output.
Code No.Diagnostic Code Detecting ConditionTrouble Area
41
(1) Open or short in throttle position sensor circuit(VTA1) for 0.5 sec. or more.
Open or short in throttle position sensor cir-
cuit.
41(2) IDL1 contact is ON and VTA1 output exceeds 1.5 V for 0.5 sec. or more.
Throttle position sensor

ECU
47
(1) Open or short in sub±throttle position sensor
circuit (VTA2) for 0.5 sec. or more.
Open or short in sub±throttle position sensor
circuit.
47(2) IDL2 contact is ON and VTA2 output exceeds 1.5 V for 0.5 sec. or more.
Sub±throttle position sensor

ECU
HINT:
Diag. code 41 is for the throttle position sensor circuit.
Diag. code 47 is for the sub±throttle position sensor circuit.
w When the connector for the (sub±) throttle position sensor is disconnec\
ted, diagnostic code 41 or 47 is not
displayed. Diagnostic code 41 or 47 is displayed only when there is an open or short in the VTA signal circuit
of the (sub±) throttle position sensor.
w Signals from the (sub±) throttle position sensor are also input to the TRAC ECU, So when a malfu\
nction
occurs on the TRAC side, code 41 or 47 may be displayed.
TR±94
±
ENGINE TROUBLESHOOTING Circuit Inspection
WhereEverybodyKnowsYourName

Coolant which is heated in the water jacket is pumped to the radiator, through which a cooling fan blows
air to cool the coolant as it passes through. Coolant which has been coo\
led is then sent back to the engine by
the water pump, where it cools the engine. The water jacket is a network of channels in the shell of the cylinder bloc\
k and cylinderhead through which
coolant passes. It is designed to provide adequate cooling through the cylinders and combus\
tion chambers
which become heated during engine operation.
RADIATOR The radiator performs the function of cooling the coolant which has pass\
ed through the waterjacket and
become hot, and it is mounted in the front of the vehicle. The radiator consis\
ts of an upper tank and lower tank,
and a core which connects the two tanks. The upper tank contains the inlet \
for coolant from the water jacket
and the filler inlet. It also has a hose attached through which excess cool\
ant or steam can flow. The lower tank
contains the outlet for coolant and drain plug. The core contains many t\
ubes through which coolant flows from
the upper tank to the lower tank as well as cooling fins which radiate heat\
away from the coolant in the tubes.
The air sucked through the radiator by the cooling fan, as well as the wind generated by the ve\
hicle's travel,
passes through the radiator, cooling the coolant. Models with automatic transmission include an aut\
omatic
transmission fluid cooler built into the lower tank of the radiator. A cooling fan is mounted behind radiator to assist
the flow of air through the radiator. When the coolant temperature is low, the fan operates slowly to help the warm
up, and when the coolant temperature becomes high, the fan speed is increas\
ed to provide the air flow required
for cooling.
RADIATOR CAP (on Reservoir Tank)
The radiator cap is a pressure type cap which seals the radiator, resulting in pressurization of the radiator
as the coolant expands. The pressurization prevents the coolant from boi\
ling even when the coolant tempera-
ture exceeds 100 5C (212 5F). A relief valve (pressurization valve) and a vacuum valve (negati\
ve pressure valve)
are built into the radiator cap. The relief valve opens and lets steam esca\
pe through the overflow pipe when
the pressure generated inside the cooling system exceeds the limit (coolant temperature: 110±120 5C
(230±248 5F) pressure; 29.4±98.1 kPa (0.3±1.0 kgf/cm2, 4.3±14.2 psi)). The vacuum v\
alve opens to alleviate
the vacuum which develops in the coolant system after the engine is stopped\
and the coolant temperature
drops.
RESERVOIR TANK The purpose of the reservoir tank is to catch coolant overflows created by \
volumetrix expansion when the
coolant temperature increases. The cap of the reservoir tank is a pressure type\
which prevents deterioration
of the LLC (Long Life Coolant) caused by contact with atmospheric air, increases vaporization performance and
reduces loss of the coolant volume.
WATER PUMP The water pump is mounted on the front of the cylinder block and driven by t\
he reverse side of the timing
belt.
THERMOSTAT The thermostat has a wax type by±pass valve and is mounted in the wat\
er inlet housing. The thermostat
begins to open at the temperature of 80 5C (180 5F). When the coolant temperature is low, the valve closes to
prevent coolant flow to the radiator, thus permitting the engine to warm up rapidly. When the by±pass valve
opens the by±pass circuit, the engine coolant continues to circulate \
inside the engine, quickly and uniformly
warming up to the appropriate temperature. When the coolant temperature is high\
, the valve opens and coolant
flows to the radiator where it is cooled. When the wax inside the thermostat \
is heated, it expands and thus
creates pressure which overpowers the force of the spring which keeps the valve\
closed. When the wax cools,
its contraction causes the force of the spring to take effect once more, closing the valve.
ELECTRONICALLY CONTROLLED HYDRAULIC COOLING FAN (See page CO±22)
±
COOLIING SYSTEM DescriptionCO±3
WhereEverybodyKnowsYourName

DESCRIPTION
By operating the driving position memory and return switch the driver's seat, steering wheel and outer mir-
ror are moved to their respective memorized positions.
 

Parts Name\
 
\

\
Function 




Tilt & Telescopic ECU
\
 
\


\

\

Control the manual operation, return operation and memory and return ope\
ration for tilt
and telescopic of steering wheel.
 Auto Set Switch\
 \
This switch is a main switch for the away operation of tilt and telescop\
ic.
 




Manual Switch\
 
\


\

\

This switch is an operation switch to operate tilt and telescopic manual\
ly. When one of tilt
up, tilt down, telescopic Extension and telescopic Contraction is operat\
ed, steering wheel
will be able to set on the optional position within the extent of operat\
ing.
 


Driving Position
Memory and
Return Switch\
 
\

\

Operating this switch makes return operation that driver seat steering w\
heel and outer mirror
are set on the memorized position working together power seat and outer \
mirror.
 

Position Sensor
\
 
\

\
Tilt position sensor detect an amount of tilt and input it to ECU.
Telescopic position sensor detect an amount of slide and input it to ECU.\
 

Motor
\
 
\

\
There is a tilt motor and telescopic motor respectively. These are operated by a signal from
the ECU.
SR±40±
STEERING STEERING COLUMN
WhereEverybodyKnowsYourName

Diag. Code 41, 47(Sub±) Throttle Position Sensor Circuit
CIRCUIT DESCRIPTION
The throttle position sensor is mounted in the throttle body
and detects the throttle valve opening angle. When the
throttle valve is fully closed, the IDL contacts in the throttle
position sensor are on, so the voltage at the terminal IDL of
the ECU become 0 V. At this time, a voltage of approximately
0.7 V is applied to the terminal VTA of the ECU. When the
throttle valve is opened, the IDL contacts go off and thus the
power source voltage of approximately 12 V in the ECU is ap-
plied to the terminal IDL of the ECU. The voltage applied to
the terminal VTA of the ECU increases in proportion to the
opening angle of the throttle valve and becomes approxi-
mately 3.5±5.0 V when the throttle valve is fully opened. The
ECU judges the vehicle driving conditions from these signals
input from the terminals VTA and IDL, and uses them as one
of the conditions for deciding the air±fuel ratio correction,
power increase correction and fuel±cut control etc. The sub±
throttle position sensor is built and operates in the same way
as the main throttle position sensor. This sensor is used for
traction control. The sub±throttle valve is opened and closed
by the sub±throttle actuator according to signals from the
TRAC ECU to control the engine output.
Code No.Diagnostic Code Detecting ConditionTrouble Area
41
(1) Open or short in throttle position sensor circuit(VTA1) for 0.5 sec. or more.
Open or short in throttle position sensor cir-
cuit.
41(2) IDL1 contact is ON and VTA1 output exceeds 1.5 V for 0.5 sec. or more.
Throttle position sensor

ECU
47
(1) Open or short in sub±throttle position sensor
circuit (VTA2) for 0.5 sec. or more.
Open or short in sub±throttle position sensor
circuit.
47(2) IDL2 contact is ON and VTA2 output exceeds 1.5 V for 0.5 sec. or more.
Sub±throttle position sensor

ECU
HINT:
Diag. code 41 is for the throttle position sensor circuit.
Diag. code 47 is for the sub±throttle position sensor circuit.
w When the connector for the (sub±) throttle position sensor is disconnec\
ted, diagnostic code 41 or 47 is not
displayed. Diagnostic code 41 or 47 is displayed only when there is an open or short in the VTA signal circuit
of the (sub±) throttle position sensor.
w Signals from the (sub±) throttle position sensor are also input to the TRAC ECU, So when a malfu\
nction
occurs on the TRAC side, code 41 or 47 may be displayed.
TR±94
±
ENGINE TROUBLESHOOTING Circuit Inspection
WhereEverybodyKnowsYourName

Diag. Code 41, 47(Sub±) Throttle Position Sensor Circuit
CIRCUIT DESCRIPTION
The throttle position sensor is mounted in the throttle body
and detects the throttle valve opening angle. When the
throttle valve is fully closed, the IDL contacts in the throttle
position sensor are on, so the voltage at the terminal IDL of
the ECU become 0 V. At this time, a voltage of approximately
0.7 V is applied to the terminal VTA of the ECU. When the
throttle valve is opened, the IDL contacts go off and thus the
power source voltage of approximately 12 V in the ECU is ap-
plied to the terminal IDL of the ECU. The voltage applied to
the terminal VTA of the ECU increases in proportion to the
opening angle of the throttle valve and becomes approxi-
mately 3.5±5.0 V when the throttle valve is fully opened. The
ECU judges the vehicle driving conditions from these signals
input from the terminals VTA and IDL, and uses them as one
of the conditions for deciding the air±fuel ratio correction,
power increase correction and fuel±cut control etc. The sub±
throttle position sensor is built and operates in the same way
as the main throttle position sensor. This sensor is used for
traction control. The sub±throttle valve is opened and closed
by the sub±throttle actuator according to signals from the
TRAC ECU to control the engine output.
Code No.Diagnostic Code Detecting ConditionTrouble Area
41
(1) Open or short in throttle position sensor circuit(VTA1) for 0.5 sec. or more.
Open or short in throttle position sensor cir-
cuit.
41(2) IDL1 contact is ON and VTA1 output exceeds 1.5 V for 0.5 sec. or more.
Throttle position sensor

ECU
47
(1) Open or short in sub±throttle position sensor
circuit (VTA2) for 0.5 sec. or more.
Open or short in sub±throttle position sensor
circuit.
47(2) IDL2 contact is ON and VTA2 output exceeds 1.5 V for 0.5 sec. or more.
Sub±throttle position sensor

ECU
HINT:
Diag. code 41 is for the throttle position sensor circuit.
Diag. code 47 is for the sub±throttle position sensor circuit.
w When the connector for the (sub±) throttle position sensor is disconnec\
ted, diagnostic code 41 or 47 is not
displayed. Diagnostic code 41 or 47 is displayed only when there is an open or short in the VTA signal circuit
of the (sub±) throttle position sensor.
w Signals from the (sub±) throttle position sensor are also input to the TRAC ECU, So when a malfu\
nction
occurs on the TRAC side, code 41 or 47 may be displayed.
TR±94
±
ENGINE TROUBLESHOOTING Circuit Inspection
WhereEverybodyKnowsYourName