warning LEXUS SC400 1991 Service Manual Online

OKNG
OKNG
INSPECTION PROCEDURE
1Check ABS warning light.
See Combination Meter Troubleshooting on page BE±159.
Replace bulb or combination meter assembly.
2Check ABS solenoid relay.
C
OK
P
OK
C
Remove solenoid relay from R/B No. 6.
Check continuity between each terminal of ABS sole-
noid relay shown below.
1. Apply battery voltage between terminals 4 and 6.
2. Check continuity between each terminal of ABS so-
lenoid relay shown below.
Replace ABS solenoid relay.
Repair or replace and check for open in harness and connector between ch\
eck connector and ABS
solenoid relay and body ground (See page IN±33).
BR±146±
BRAKE SYSTEM ANTI±LOCK BRAKE SYSTEM (ABS)
WhereEverybodyKnowsYourName

NOYES
YESNO
OKNG
INSPECTION PROCEDURE
3Is diagnosis trouble code output?
Perform diagnostic trouble code check on page BR±76.
Repair circuit indicated by the code output.
4Does ABS warning light go off if short pin is removed?
Check for short in harness and connector between warn-
ing light and data link connector 1 and ECU (See page
IN±33 ).
5Check ABS solenoid relay (See step No. ).
Replace ABS solenoid relay.
Repair or replace and check for short in harness
and connector between data link connector 1 and
ABS solenoid relay (See page IN±33).
±
BRAKE SYSTEM ANTI±LOCK BRAKE SYSTEM (ABS)BR±147
WhereEverybodyKnowsYourName

IN±33).
WIRING DIAGRAM
Tc Terminal Circuit
CIRCUIT DESCRIPTION
Connecting between terminals Tc and E1 of the DLC1 or the DLC2 causes the ECU to display the diagnos-
tic trouble code by flashing the ABS warning light.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
BR±148±
BRAKE SYSTEM ANTI±LOCK BRAKE SYSTEM (ABS)
WhereEverybodyKnowsYourName

NGOK
OKNG
INSPECTION PROCEDURE
1Check voltage between terminals Tc and E1 of DLC2 or DLC1.
C
OK
PTurn ignition switch ON.
Measure voltage between terminals Tc and E1 of DLC2
or DLC1.
Voltage: 10 ± 14 V
If ABS warning light does not blink even after Tc and E1
are connected,t he ECU may be defective.
2Check for open and short in harness and connector between ABS (& TRAC) ECU \
and DLC2 or
DLC1, DLC2 or DLC1 and body ground (See page IN±33).
Repair or replace harness or connector.
Check and replace ABS (& TRAC) ECU.
±
BRAKE SYSTEM ANTI±LOCK BRAKE SYSTEM (ABS)BR±149
WhereEverybodyKnowsYourName

NGOK
OKNG
INSPECTION PROCEDURE
1Check voltage between terminal Ts and E1 of data link connector 1.
C
OK
PTurn ignition switch ON.
Measure voltage between terminals Ts and E1 of DLC1.
Voltage: 10 ± 14 V
If ABS warning light does not blink even after Ts and E1
are connected, the ECU may be defective.
2Check for open and short in harness and connector between ABS (& TRAC) ECU and D\
LC1,
DLC1 and body ground (See page IN±33).
Repair or replace harness or connector.
Check and replace ABS (& TRAC) ECU.
±
BRAKE SYSTEM ANTI±LOCK BRAKE SYSTEM (ABS)BR±151
WhereEverybodyKnowsYourName

ECU TERMINALS STANDARD VALUE
ABS & TRAC ECU:
BR0F8±03
 Symbols
(Terminals No.) STD Voltage (V)\
 \
Condition
 

BAT
(A25±21)
 

±
 

GND
(A25±22)
 

10±14
\
 
\

\
Always
 

IG
(A24±24) 

±
 

GND
(A25±22) 

10±14
\
 
\

\
IG switch ON
 

SR
(A24±22) 

±
 

R±
(A24±25) 

8.3±14
\
 
\

\
IG switch ON, ABS warning light OFF
 


MR
(A25±16) 

± 


R±
(A24±25) 

Below 1.0\
 
\

\
IG switch ON
 


TSR
(A24±1) 

± 


R±
(A24±25) 

8.3±14\
 
\

\
IG switch ON, TRAC indicator light OFF
 


TMR
(A24±9) 


± 


R±
(A24±25) 


Below 1.0\
 
\

\

IG switch ON
 SFR
(A25±1) ± GND
(A25±2) 10±14\
 \
IG switch ON, ABS warning light OFF
 

SFL
(A24±13) 

±
 

GND
(A25±22) 

10±14
\
 
\

\
IG switch ON, ABS warning light OFF
 

SRR
(A24±26) 

±
 

GND
(A25±22) 

10±14
\
 
\

\
IG switch ON, ABS warning light OFF
 


SRL
(A25±12) 

±
 


GND
(A25±13) 

10±14
\
 
\

\
IG switch ON, ABS warning light OFF
 


AST
(A24±8) 

± 


GND
(A25±22) 

10±14\
 
\

\
IG switch ON, ABS warning light OFF
 


SAC
(A24±12) 


± 


GND
(A25±22) 


10±14\
 
\

\

IG switch ON, TRAC indicator light OFF
 SMC
(A24±2) ± GND
(A25±22) 10±14\
 \
IG switch ON, TRAC indicator light OFF
 

SRC
(A24±15)
 

±
 

GND
(A25±22
 

10±14
\
 
\

\
IG switch ON, TRAC indicator light OFF
 

PR
(A24±10) 

±
 

E2
(A24±20) 

5±7
\
 
\

\
IG switch ON
 


VC
(A24±19) 

±
 


E2
(A24±20) 

4±6
\
 
\

\
IG switch ON
 ALT 
±
 GND Below 1.0\
 \
IG switch ON
 ALT
(A25±8) ± GND
(A25±22) 10±14\
 \
Idling
 
WA
 
±
 
GND
 Below 2.0\
 \
IG switch ON, ABS warning light ON WA
(A25±9) ± GND
(A25±22) 10±14\
 \
IG switch ON, ABS warning light OFF 


PKB
 


±
 


GND
 

Below 1.5
\
 
\

\
IG switch ON, PKB switch ON,
Fluid in M/C reservoir above MIN level
 


PKB
(A25±17) 


± 


GND
(A25±22) 

10±14
\
 
\

\
IG switch ON, PKB switch OFF,
Fluid in M/C reservoir above MIN level
BR±158±
BRAKE SYSTEM TRACTION CONTROL SYSTEM (TRAC)
WhereEverybodyKnowsYourName

 



Symbols
(Terminals No.) 


STD Voltage (V)\
 
\

\

Condition
 LBL
(A25±6)  ± GND
(A25±22) 10±14\
 \
IG switch ON
Fluid in M/C reservoir tank above MIN level.
 

STP
 

±
 

GND
 

Below 1.5\
 
\

\
Stop light switch OFF 


STP
(A25±10) 
± 


GND
(A25±22) 

8±14
\
 
\

\
Stop light switch ON
 D/G
(A25±20) ± GND
(A25±22) 10±14\
 \
IG switch ON, ABS warning light OFF
 

Tc
(A26±3)
 

±
 

GND
(A25±22)
 

10±14
\
 
\

\
IG switch ON
 

Ts
(A26±1) 

±
 

GND
(A25±22) 

10±14
\
 
\

\
IG switch ON
 P 
±
 GND 10±14\
 \
IG switch ON, Shift position in ªPº position P
(A26±10) ± GND
(A25±22) Below 1.5\
 \
IG switch ON, Other shift position in ªPº position 

N
 

±
 

GND
 

10±14\
 
\

\
IG switch ON, Shift position in ªNº position
 
N
(A26±5) 
±
 
GND
(A25±22) Below 1.5\
 \
IG switch ON, Other shift position in ªNº position
 

FR+
(A24±17) ± 

FR±
(A24±4) 

AC generation\
 
\

IG switch ON
Slowly turn right front wheel.
 

FL+
(A24±5)
 

±
 

FL±
(A24±18)
 

AC generation
\
 
\

\
IG switch ON
Slowly turn left front wheel.
 

RR+
(A25±14) 

±
 

RR±
(A25±3) 

AC generation
\
 
\

\
IG switch ON
Slowly turn right rear wheel.
 

RL+
(A25±4) 

±
 

RL±
(A25±15) 

AC generation
\
 
\

\
IG switch ON
Slowly turn left rear wheel.
 


FRO
(A26±15) 
± 


GND
(A25±22) 

Pulse generation\
 
\

\

IG switch ON
Slowly turn right front wheel.
 


FLO
(A26±6) 
± 


GND
(A25±22) 

Pulse generation\
 
\

\

IG switch ON
Slowly turn left front wheel.
 


RRO
(A26±13) 
± 


GND
(A25±22) 


Pulse generation\
 
\

\

IG switch ON
Slowly turn right rear wheel.
 RLO
(A26±4) ± GND
(A25±22) Pulse generation\
 \
IG switch ON
Slowly turn left rear wheel.
±
BRAKE SYSTEM TRACTION CONTROL SYSTEM (TRAC)BR±159
WhereEverybodyKnowsYourName

SYSTEM CIRCUIT
OPERATION
When the ignition switch is turned ON, current from the battery flows from t\
erminal L of the alternator through
the IC regulator to terminal E, causing the discharge warning light to ligh\
t up. Then when the engine is started, the voltage output increases as the alt\
ernator rpm increases. When the
voltage output becomes greater than the battery voltage, current for recharging\
flows from terminal B. Simulta-
neously, volt age at terminal L increases and the potential difference between battery and terminal L disappears,
causing the discharge warning light to go off. When the voltage output exceeds the regulator adjustment volt-
age, the transistor inside the IC regulator regulates the voltage so tha\
t the voltage from the alternator remains
constant.
±
CHARGING SYSTEM System Circuit, OperationCH±3
WhereEverybodyKnowsYourName

(b) Check the belt tensioner operation.w Check that the belt tensioner moves downward
when the drive belt is pressed down at the points
indicated in the illustration with approx. 98 N ( 10
kgf, 22.0 lbf) of force.
w Check the alignment of the belt tensioner pulley to
make sure the drive belt has not slipped off the
pulley.
If necessary, replace the belt tensioner.
w Check that the arrow mark on the belt tensioner falls
within area A of the scale.
If it is outside area A, replace the drive belt.
HINT:
w When a new belt is installed, it should lie within area B.
If not, the drive belt is not correct.
w After installing a belt, check that it fits properly in the
ribbed grooves.
w Check by hand to confirm that the belt has not slipped
out of the groove on the bottom of the pulley.
4. REMOVE ENGINE UNDER COVER
5. VISUALLY CHECK ALTERNATOR WIRING AND LISTEN FOR ABNORMAL NOISES
(a) Check that the wiring is in good condition.
(b) C h e c k t h a t t h e r e i s n o a bnormal noise from the
alternator while the engine is running.
6. INSPECT CHARGE WARNING LIGHT CIRCUIT (a) Warm up the engine and then turn it off.
(b) Turn off all accessories.
(c) Turn the ignition switch ON. Check that the charge
warning light is lit.
(d) Start the engine. Check that the light goes off.
If the light does not go off as specified, troubleshoot the
charge light circuit.
CH±6
±
CHARGING SYSTEM On±Vehicle Inspection
WhereEverybodyKnowsYourName

Steering Wheel Pad (Airbag and Inflator)
Junction Block No. 1 Center Airbag
Front Airbag Sensor
Front Airbag Sensor
Warning Light Spiral Cable (in Combination Switch)
HANDLING PRECAUTIONS ON RELATED COMPONENTS
1. SRS AIRBAG
Locations of Airbag Components
This vehicle has an SRS AIRBAG (referred to as the airbag in the remain\
der of this manual).
When handling airbag components (removal, installation or inspection, e\
tc.), always follow the directions
given in the repair manual for the relevant model year to prevent the oc\
currence of accidents and airbag
malfunction.
Also take the following precautions when repairing the body:

Work must be started after 20 seconds or longer from the time the ignitio\
n switch is set to the LOCK
position and the negative (-) terminal cable is disconnected from the \
battery.
(The airbag system is equipped with a back-up power source so that if w\
ork is started within 20 seconds
of disconnecting the negative (-) terminal cable of the battery, the airbag may be deployed.)
When the negative (-) terminal cable is disconnected from the battery, memory of the clock and audio
systems will be cancelled. So before starting work, make a record of the\
contents memorized by each
memory system. Then when work is finished, reset the clock and audio sys\
tems as before.
When the vehicle has tilt and telescopic steering, power seat, and outsi\
de rear view mirror, which are all
equipped with memory function, it is not possible to make a record of th\
e memory contents.
So when the operation is finished, it will be necessary to explain this \
fact to the customer, and request
the customer to adjust the features and reset the memory.
To avoid erasing the memory of each memory system, never use back-up powe\
r supply from outside
the vehicle.

When using electric welding, first disconnect the airbag connector (yel\
low color and 2 pins) under the
steering column near the combination switch connector before starting wo\
rk.
Sensor Assembly
INTRODUCTIONIN-6
WhereEverybodyKnowsYourName