ECU LEXUS SC400 1991 Service Repair Manual

11 6
THEFT DETERRENT AND DOOR LOCK CONTROL
D 7, D 8 DOOR KEY LOCK AND UNLOCK SW LH, RH
1±2 : CLOSED WITH DOOR LOCK CYLINDER UNLOCKED WITH KEY
3±2 : CLOSED WITH DOOR LOCK CYLINDER LOCKED WITH KEY
D10, D11 DOOR LOCK MOTOR, DOOR UNLOCK DETECTION SW AND DOOR OPEN DETECTION SW LH, RH
1±4: CLOSED WITH UNLOCK POSITION
E 5 ENGINE HOOD COURTESY SW
1±2: CLOSED WITH ENGINE HOOD OPEN
I15 UNLOCK WARNING SW [IGNITION SW]
9±10: CLOSED WITH IGNITION KEY IN CYLINDER
L 5 LUGGAGE COMPARTMENT KEY UNLOCK SW
1±3: CLOSED WITH DOOR LOCK CYLINDER UNLOCK WITH KEY
L 6 LUGGAGE COMPARTMENT LIGHT SW
1±GROUND: CLOSED WITH DOOR OPEN
T 8(B) THEFT DETERRENT AND DOOR LOCK ECU
1±GROUND: CONTINUITY WITH LUGGAGE COMPARTMENT DOOR TO UNLOCK POSITION
12±GROUND: CONTINUITY WITH ENGINE HOOD OPEN
10±GROUND: CONTINUITY WITH LUGGAGE COMPARTMENT DOOR OPEN
7±GROUND: APPROX. 12 VOLTS WITH IGNITION SW AT ACC OR ON POSITION
T 9(A) THEFT DETERRENT AND DOOR LOCK ECU
1±GROUND: APPROX. 12 VOLTS WITH SHIFT LEVER IN N OR P POSITION AND IGNITION SW AT ST POSITION
2±GROUND: APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
6±GROUND: CONTINUITY WITH IGNITION KEY IN CYLINDER
7±GROUND: CONTINUITY WITH FRONT RH DOOR TO UNLOCK POSITION
8±GROUND: ALWAYS APPROX. 12 VOLTS
10±GROUND: CONTINUITY WITH DOOR LOCK KEY SW LH TO UNLOCK POSITION
11±GROUND: CONTINUITY WITH FRONT LH DOOR TO UNLOCK POSITION
12±GROUND: CONTINUITY WITH FRONT RH DOOR OPENED
13±GROUND: CONTINUITY WITH FRONT LH DOOR OPENED
14±GROUND: CONTINUITY WITH DOOR LOCK KEY SW RH TO LOCK POSITION
15±GROUND: CONTINUITY WITH DOOR LOCK KEY SW RH TO UNLOCK POSITION
20±GROUND: ALWAYS APPROX. 12 VOLTS
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C1428F 926N 127
C2328F1028P 531
D 730F1430T 127
D 830I1529T 8B29
D 930L 129T 9A29
D1030L 430T1529
D1130L 530
E 526L 630
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
219ENGINE COMPARTMENT LEFT
422LEFT KICK PANEL (J/B NO.1 LEFT)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B20ENGINE ROOM MAIN WIRE
1D20FRONT DOOR LH WIRE
1E20INSTRUMENT PANEL WIRE
1H
1I20COWL WIRE1J20COWL WIRE
1K
3A22INSTRUMENT PANEL WIRE3F22INSTRUMENT PANEL WIRE
SERVICE HINTS
WhereEverybodyKnowsYourName

11
FINDING A SHORT CIRCUIT
(a) Remove the blown fuse and disconnect all loads of thefuse.
(b) Connect a test bulb in place of the fuse.
(c) Establish conditions in which the test bulb comes on.
Example: ± Ignition SW on
± Ignition SW and SW 1 on
± Ignition SW, SW 1 and Relay on (Connect theRelay) and SW 2 off (or Disconnect SW 2)
(d) Disconnect and reconnect the connectors while watching the test bulb.
The short lies between the connector where the test
bulb stays lit and the connector where the bulb goes
out.
(e) Find the exact location of the short by lightly shaking the problem wire along the body.
CAUTION:
(a) Do not open the cover or the case of the ECU unlessabsolutely necessary. (If the IC terminals are touched,
the IC may be destroyed by static electricity.)
(b) When replacing the internal mechanism (ECU part) of the digital meter, be careful that no part of your body or
clothing comes in contact with the terminals of leads
from the IC, etc. of the replacement part (spare part).
DISCONNECTION OF MALE AND FEMALE
CONNECTORS
To pull apart the connectors, pull on the connector itself, not the
wire harness.
HINT: Check to see what kind of connector you are disconnecting
before pulling apart.
WhereEverybodyKnowsYourName

15
ABBREVIATIONS
DISCONNECTION AND CONNECTION OF BOLT
TYPE CONNECTORS
For engine and ECT ECU in this vehicle, connectors are used
which require a bolt built into the connector to be screwed down to
securely connect the connector.
1. Disconnect the connectorAfter completely loosening the bolt, the two parts of the
connector can be separated.
NOTICE:
Do not pull the wire harness when disconnecting the
connector.
2. Connect the connector
NOTICE:
Before connecting the connector, always check that the
terminals are not bent or damaged.
(a) Match the guide section of the male connectorcorrectly with the female connector, then press them
together.
(b) Tighten the bolt. Make sure the connectors are completely connected,
by tightening the bolt until there is a clearance of less
than 1 mm (0.04 in.) between the bottom of male
connector and the end of female connector.
ABBREVIATIONS
The following abbreviations are used in this manual.
A/C = Air Conditioning O/D = Overdrive
ABS = Anti±Lock Brake System R/B = Relay Block
A/T = Automatic Transmission RH = Right±Hand
CB = Circuit Breaker SRS = Supplement Restraint System
COMB. = Combination SW = Switch
ECT = Electronic Controlled Transmission TDCL = Total Diagnostic Communication Link
ECU = Electronic Control Unit TEMP. = Temperature
EGR = Exhaust Gas Recirculation TRAC = Traction Control
FL = Fusible Link VSV = Vacuum Switching Valve
ISC = Idle Speed Control W/ = With
J/B = Junction Block W/O = Without
LH = Left-Hand
* The titles given inside the components are the names of the terminals (ter\
minal codes) and are not treatedas being abbreviations.
WhereEverybodyKnowsYourName