brake fluid LEXUS SC400 1991 Service Repair Manual

ABBREVIATIONS USED IN THIS
MANUAL
ABS Anti±Lock Brake System J/B Junction Block
A/C Air Conditioner LED Light Emitting Diode
ALR Automatic Locking Retractor LH Left±Hand
APPROX. Approximation LHD Left±Hand Drive
A/T, ATM Automatic Transmission LLC Long Life Coolant (Year Around Coolant)
ATF Automatic Transmission Fluid Max. Maximum
BTDC Before Top Dead Center Min. Minimum
BVSV Bimetal Vacuum Switching Valve MP Multipurpose
CALIF. Vehicles Sold in California N Neutral
CB Circuit Breaker OD, O/D Overdrive
DOHC Double Over Head Cam O/S Oversize
DP Dash Pot P & BV Proportioning and Bypass Valve
ECT Electronic Controlled Transmission PCV Positive Crankcase Ventilation
ECU Electronic Controlled Unit PS Power Steering
EFI Electronic Fuel Injection RH Right±Hand
EGR Exhaust Gas Recirculation RL Rear Left
ELR Emergency Locking Retractor RR Rear Right
EPR Evaporator Pressure Regulator RR, Rr Rear
ESA Electronic Spark Advance SRS Supplemental Restraint System
EVAP Evaporative (Emission Control) SSM Special Service Materials
EX Exhaust (manifold, valve) SST Special Service Tools
Ex. Except STD Standard
FIPG Formed in Place Gasket SW Switch
FL Front Left TDC Top Dead Center
FL Fusible Link TDCL Total Diagnostic Communication Link
FPU Fuel Pressure Up Temp. Temperature
FR Front Right TRAC Traction Control System
FR, Fr Front TWC Three±Way Catalyst
HAC High Altitude Compensation VSV Vacuum Switching Valve
IG Ignition VTV Vacuum Transmitting Valve
IN Intake (manifold, valve) w/ With
INT Intermittent w/o Without
ISC Idle Speed Control
IN±34±
INTRODUCTION Abbreviations Used in This Manual
WhereEverybodyKnowsYourName

12. Observe the following precautions to avoid damage to theparts:
(a) Do not open the cover or case of the ECU unless
absolutely necessary (If the IC terminals are touched, the
IC may be destroyed by static electricity.).
(b) To pull apart electrical connectors, pull on the connectoritself, not the wires (See page BE±2).
(c) Be careful not to drop electrical components, such as sensors or relays. It they are dropped on a hard floor,
they should be replaced and not reused.
(d) When checking continuity at the wire connector, insert the tester probe carefully to prevent terminals from
bending.
(e) To disconnect vacuum hoses, pull on the end, not the middle of the hose.
(f) When steam cleaning an engine, protect the distributor,
coil and air filter from water.
(g) Ne ve r use an imp a ct wre n ch to re mo ve or in sta ll temperature switches or temperature sensors.
(h) When using a vacuum gauge, never force the hose onto
a connector that is too large. Use a step±down adapter
instead. Once the hose has been stretched, it may leak.
13. Tag hoses before disconnecting them: (a) When disconnecting vacuum hoses, use tags to identify
how they should be reconnected.
(b) After completing a job, double check that the vacuum hoses are properly connected. A label under the hood
shows the proper layout.
14. Installation of wheels The wheel assemblies are of the uni±directional type and
must be rotated only between the front and rear as illustrated.
Wheels are marked with turning direction indicators.
When installing the wheels, check the marks carefully and
install the wheel correctly.
15. Bleeding of traction control system When repairing the brake master cylinder or TRAC system,
bleed the air out of the TRAC system (See page BR±7).
CAUTION: Since the fluid is under high pressure, it could
spray out with great force, so be careful.
IN±6
±
INTRODUCTION General Repair Instructions
WhereEverybodyKnowsYourName

AT00S±01
PRELIMINARY CHECK
1. CHECK FLUID LEVELHINT:
wDrive the vehicle so that the engine and transmission
are at normal operating temperature.
Fluid temp.: 70±80 5C (158±176 5F)
w Only use the COOL range on the dipstick as a rough
reference when the fluid is replaced or the engine does
not run.
(a) Park the vehicle on a level surface and set the parking brake.
(b) With the engine idling and the brake pedal depressed, shift the shift lever into all positions from P to L position and return
to P position.
(c) Pull out the transmission dipstick and wipe it clean.
(d) Push it back fully into the tube.
(e) Pull it out and check that the fluid level is in the HOT range. If the level is at the low side, add fluid.
Fluid type:
ATF TYPE T±II or Equivalent
NOTICE: Do not overfill.
2. CHECK FLUID CONDITION If the fluid smells burnt or is black, replace it.
3. REPLACE TRANSMISSION FLUID
(a) Remove the drain plug and drain the fluid.
(b) Reinstall the drain plug securely.
(c) With the engine OFF, add new fluid through the oil filler tube.
Fluid type:
ATF TYPE T±II or Equivalent
Capacity:
Total: 8.2 liters (8.7 US qts, 7.2 lmp. qts)
Drain and refill: 1.9 liters (2.0 US qts, 1.7 lmp. qts)
(d) Start the engine and shift the shift lever into all positions fromP to L position and then shift into P position.
(e) With the engine idling, check the fluid level. Add fluid up to the
COOL level on the dipstick.
±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION TROUBLESHOOTINGAT±47
WhereEverybodyKnowsYourName

MECHANICAL SYSTEM TESTS
AT0QT±01
STALL TESTThe object of this test is to check the overall performance of the trans\
mission and engine by measuring
the stall speeds in the D and R positions.
NOTICE:
 Perform the test at normal operating fluid temperature 50±80 C (122±176 F).
 Do not continuously run this test longer than 5 seconds.
 To ensure safety, conduct this test in a wide, clear, level area, which provides good traction.
 The stall test should always be carried out in pairs. One technician sho\
uld observe the conditions of
wheels or wheel stoppers outside the vehicle while the other is performi\
ng the test.
MEASURE STALL SPEED
(a) Chock the 4 wheels.
(b) Connect a tachometer to the engine.
(c) Fully apply the parking brake.
(d) Keep your left foot pressed firmly on the brake pedal.
(e) Start the engine.
(f) Shift into the D position. Step all the way down on the accelerator peda\
l with your right foot.
Quickly read the stall speed at this time.
Stall speed:
2,200 + 150 RPM
(g) Perform the same test in R position.
AT±50±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION TROUBLESHOOTING
WhereEverybodyKnowsYourName

EVALUATION
 

Problem\
 
\

\
Possible cause 


\
 
\

\

Engine output may be insufficient.
 \
 \
 Stator one±way clutch is operating properly
 (a) Stall speed low in D and R positions.\
 \
HINT:
 \
 \
If more than 600 RPM below the specified value, the
 \
 \
torque converter could be faulty.
 \
 \
 Line pressure too low
 
(b) Stall speed high in Dposition
\
 \
 Forward clutch slopping 

(b) Stall speed high in D position.\
 
\
 No.2 one±way clutch not operating properly 


\
 
\

\

O/D one±way clutch not operating properly
 \
 \
 Line pressure too low
 (c) Stall speed high in Rposition\
 \
 Direct clutch slipping
 (c) Stall speed high in R position.\
 \
 First and reverse brake slipping
 \
 \
 O/D one±way clutch not operating properly
 \
 \
 Line pressure too low
 (d) Stall speed high in D and R position.\
 \
 Improper fluid level 

\
 
\
 O/D one±way clutch not operating properly
±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION TROUBLESHOOTINGAT±51
WhereEverybodyKnowsYourName

TIME LAG TEST
When the shift lever is shifted while the engine is idling, there will be a \
certain time lapse or lag before the
shock can be felt. This is used for checking the condition of the O/D direct \
clutch, forward clutch, direct
clutch, and first and reverse brake.
NOTICE:
Perform the test at normal operating fluid temperature 50±80 C (122±176 F).
 Be sure to allow a one minute interval between tests.
 Make 3 measurements and take the average value.
MEASURE TIME LAG
(a) Fully apply the parking brake
(b) Start the engine and check idle speed.
Idle speed:
650 RPM (In N position and air conditioner OFF)
(c) Shift the shift lever from N to D position. Using a stop watch, measure the time it take\
s from shifting thelever until the shock is felt.
In same manner, measure the time lag for N
R.
Time lag:
N D Less than 1.2 seconds
N R Less than 1.5 seconds
AT±52±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION TROUBLESHOOTING
WhereEverybodyKnowsYourName

MEASURE LINE PRESSURE
NOTICE:
Perform the test at normal operating fluid temperature 50±80 C (122±176 F).
 The line pressure test should always be carried out in pairs. One technicia\
n should observe the
conditions of wheels or wheel stoppers outside the vehicle while the other is perf\
orming the test.
 Be careful to prevent the oil pressure gauge hose from interfering with \
the exhaust pipe.
(a) Warm up the transmission fluid.
(b) Remove the test plug on the transmission case left side and connect the \
oil pressure gauge SST.
SST 09992±00094
HINT: Connecting the oil pressure gauge will be made easier by moving LH sid\
e heat insulator aside.
(c) Fully apply the parking brake and chock the 4 wheels.
(d) Start the engine and check idling RPM.
(e) Keep your left foot pressed firmly on the brake pedal and shift into D p\
osition.
(f) Measure the line pressure when the engine is idling.
(g) Press the accelerator pedal all the way down. Quickly read the highest line pressure when engine speedreaches stall speed.
(h) In the same manner, perform the test in R position. AT±54
±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION TROUBLESHOOTING
WhereEverybodyKnowsYourName

SPECIFIED LINE PRESSURE
 
Condition
 
D positionkPa (kgf/cm2, psi)
 
R positionkPa (kgf/cm2, psi) 

Idling
 

382±441 (3.9±4.5, 55±64)
 

637±716 (6.5±7.3, 92±104) 

Stall
 

1,265±1,402 (12.9±14.3, 183±203)
 

1,726±2,060 (17.6±21.0, 250±299)
If the measured pressures are not up to specified values, recheck the thro\
ttle cable adjustment and perform
a retest.
EVALUATION
 Problem\
 \
Possible cause
 \
 \

Throttle cable out of adjustment If the measured values at all positions are higher.\
 \
 Throttle valve defective 


\

\

\

Regulator valve defective
 \
 \
 Throttle cable out of adjustment
 \
 \
 Throttle valve defective
 If the measured values at all positions are lower.\
 \
 Regulator valve defective
 \
 \
 Oil pump defective
 \
 \
 O/D direct clutch defective
 
Ifpressure is low in the Dposition only
\
 \
 D position circuit fluid leakage If pressure is low in the D position only.\
 \
 Forward clutch defective 


\

\

\

R position circuit fluid leakage
 If pressure is low in the R position only.\
 \
 Direct clutch defective
 \
 \
 First and reverse brake defective
±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION TROUBLESHOOTINGAT±55
WhereEverybodyKnowsYourName

2. HYDRAULIC CONTROL SYSTEMThe hydraulic control system is composed of the oil pump, the valve body, the solenoid valves, the accumu-
lators, the clutches and brakes, as well as the fluid passages which connect al\
l of these components.
Based on the hydraulic pressure created by the oil pump, the hydraulic control system governs the hydrau-
lic pressure acting on the torque converter clutch, clutches and brakes \
in accordance with the vehicle driv-
ing conditions.
There are 4 solenoid valves on the valve body.
The No.1 and No.2 solenoid valves are turned on and off by signals from the ECM to operate the shift
valves, and change the gear shift position.
The No.3 solenoid valve is operated by signals from the ECM to engage or di\
sengage the lock±up clutch
of the torque converter clutch.
The No.4 solenoid valve is operated by signals from the ECM to control the \
engagement speed and reduce
gear shift shock.
±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION OPERATIONAT±7
WhereEverybodyKnowsYourName

EQUIPMENT
AT06V±05\
 \
Feeler gauge Check major clearance\
 
\

\
Vernier calipers
 

Check length of second coast brake
piston rod.
\
 
\

\
Dial indicator or dial indicator with magnetic baseCheck piston stroke and end play of
the output shaft.
\
 
\

\
Dial indicator with magnetic baseCheck inside diameter of major
bushing.
\
 \
Straight edgeCheck side clearance of oil pump.
\
 \
Torque wrench
\
 
\

\
Cylinder gaugeCheck inside diameter of the trans-
mission case rear bushing.
\
 \
Voltmeter
\
 \
Ammeter(A)
\
 \
Ohmmeter
LUBRICANT
AT0GW±03
 Item Capacity Classification
 Automatic transmission fluid
 Dry fill 8.2 liters (8.7 US qts, 7.2 lmp. qts) ATF Type T±II or equivalent
 Drain and refill 1.9 liters (2.0 US qts, 1.7 lmp. qts) 
SSM (SPECIAL SERVICE MATERIALS)
AT06X±03
\
 \
08826±00090 Seal Packing 1281, Transmission case X Oil pan
\
 
\

\

THREE BOND 128\
1 or equivalentTransmission case X Extension
housing
±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION PREPARATIONAT±13
WhereEverybodyKnowsYourName