climate control LINCOLN AVIATOR 2005 Quick Reference Guide

Climate Control
1AUTO: Press AUTO and select the
temperature you find most comfortable.
The system will automatically determinefan speed, airflow location and whether
outside or recirculated air is required.
2OFF: Outside air is shut out and the
fan will not operate.
3DIRECT AIRFLOW: You can personally
determine where you’d like air to go by
choosing one of these manual override
controls.
4DEFROST: To clear thin ice and fog from
the windshield, choose DEFROST; this
control will distribute outside air through
the windshield defroster ducts and the
side window demisters. To return to
automatic operation, press AUTO.
5DEFROST REAR WINDOW: Press this
control to manually enable or disable the
rear window defroster in all modes. After
approximately 10 minutes of operation,
the climate control system will
automatically disable the rear defrost
operation. If more defrosting is needed,
press the control again.
6DRIVER TEMPERATURE CONTROL: Press
the up arrow of the driver temperature
control for a warmer temperature; press
the down arrow for a cooler temperature.
7FAN SPEED: When your climate control
system is in automatic mode, the fanspeed will automatically adjust to
achievethe selected temperature. To adjust fan
speed manually, press the up arrow to
increase the speed; press the down arrow
to decrease the speed. To return to
automatic fan operation, press AUTO.
8EXTERIOR TEMPERATURE DISPLAY:
Press EXT to display the outside
temperature; press again to end exterior
temperature display.
9FAHRENHEIT/CELSIUS: Press the °F °C
control to switch between Fahrenheit andCelsius.
10A/C: You may override automatic
operation at any time by pressing the A/C
control. To return to automatic air
conditioning operation, press AUTO.
11RECIRCULATED AIR: Press this button
to manually control recirculated air; to
return to automatic recirculated air,
press AUTO.
12PASSENGER TEMPERATURE CONTROL:
Press the up arrow of the passenger
temperature control for a warmer
temperature; press the down arrow for a
cooler temperature.
13 DUAL TEMPERATURE ZONE: Press
DUAL to enable or disable the dual zone
temperature feature that allows driver and
front passenger to select a temperature
based on personal preference. Press
DUAL again to disable this feature.
Automatic Temperature Control
101112
12345
678
913

2Headlamps
Rotate the headlamp control clockwise to the second position to
turn on the headlamps. Pull the headlamp control towards you to
turn on the foglamps. Must be in autolamp mode, parklamp
position or headlamp position for foglamps to operate. Rotate
the control counterclockwise to initiate the autolamps. (This light
sensitive system turns your exterior lamps on and off automatically.
It also keeps the lights on for approximately 20 seconds after the
ignition switch is turned to the OFF position.) To turn the system off,
rotate the control clockwise to the OFF position.
3 ABS Light
Your antilock braking system (ABS) detects the onset of wheel lockup
during brake applications and helps prevent wheels from locking
during extreme braking situations. The ABS warning light will
illuminate when you start your engine; however, if it stays on,
continues to flash or fails to illuminate, see your dealership's service
department immediately.
5Speed Control
You must be traveling at or above 30 miles per hour to use the
speed control system. Press ON to enable speed control. Press
SET + to set a speed. To set a higher speed, accelerate to the
desired speed, press and release SET +. To establish a lower
speed, press and hold the SET control until you get to the desired
speed, then release the control or depress the brake pedal or
press CNCL until the desired vehicle speed is reached then press
the SET + control. To return to a previously set speed, press RES.
To disengage speed control and erase the previously programmed
set speed, press OFF.
6Audio System
Please see Audio System on the reverse side of this guide.
7Climate Control
Please see Climate Control on the reverse side of this guide.
4Service Engine Soon
This light will illuminate briefly when you start your vehicle to ensure
that the engine warning system is functional. If it comes on after the
engine is started, one of your engine’s emission control systems
may be malfunctioning. Or, it may stay on because your vehicle is out
of fuel, existing fuel quality is poor, or the fuel cap hasn’t been
properly tightened. If you have added high quality fuel or tightened
the fuel cap and the light continues to stay on, remember that it can
take three driving cycles for the light to turn off. (A driving cycle
consists of a cold engine startup followed by mixed city/highway
driving.) No additional vehicle service would be required.