set clock LINCOLN AVIATOR 2005 Quick Reference Guide

Audio System
(If your Aviator is equipped with a different audio
system, please refer to your Owner’s Guide.)
1 CD/AUX: Press to select CD/AUX
modes. No CD will display if there is not
a CD present in the audio system. If a
disc is loaded, there will be a number
(16) inside the circle on the display.
2 SCAN FUNCTION: In radio mode,
press to hear a sampling of all listenable
stations. In CD mode, press to hear abrief sampling of all selections on the
current CD.
3 LOADING CD:Press to open the CD
door, then load a CD into the player. Press
LOAD and then a preset number to select
a slot. Press and hold LOAD to activateautoload.
4 VOLUME/POWER CONTROL: Press the
control to turn the audio system on or off.
Turn the control to raise or lower volume.
The speed sensitive volume feature
automatically adjusts radio volume in
accordance with vehicle speed to
compensate for road and wind noise. To
engage, press and hold the volume
control for five seconds (with the radio
on), then simultaneously press SEL to
choose the compensation level.
5 AM/FM SELECT:In radio mode, press
AM/FM to select AM or FM frequency
bands. In CD mode, press AM/FM to stop
play and begin radio play. 6 SATELLITE:
Your Audiophile radio comes
equipped with satelliteready capability.
The kit to enable satellite reception is
available through your Lincoln dealer.
The dealerinstalled satellite kit is onlyavailable in the continental United States.
7 DISC/TUNE CAT: In radio mode, press
to move to the next frequency up or down
the band. In CD mode, press to select a
disc in the CD player. CAT is onlyavailable when equipped with satellite
radio. The kit to enable satellite reception
is available through your Lincoln dealer.
Detailed satellite instructions are
included with the dealerinstalled kit.
8 SEEK FUNCTION: In radio mode, press
to move to the next listenable station up
or down the band. In CD mode, press to
select the next/previous track on the
current disc.
9 DIGITAL SIGNAL PROCESSING: Press
DSP to access the Ambiance menu.
Press SEL to engage/disengage. Turn the
volume control to increase/decrease the
level of ambiance.
10 SETTING MEMORY PRESET STATIONS:
Select AM, FM1, or FM2 band, then
select a station. Next, press and
hold a numbered control until the
sound returns.
11 SETTING THE CLOCK:Your vehicle is
equipped with a separate indash
mounted clock. See your Owner’s Guidefor information.
Audiophile Satellite Ready InDash Six CD Radio (if equipped)
123
4
56
789
1110
*CDs with adhesive labels and irregularly shaped CDs may get stuck in the CD player.
Homemade CDs should be identified with permanent felt tip marker rather than adhesive labels.CAUTION: DO NOT USE CD WITH ADHESIVE LABEL*

2Headlamps
Rotate the headlamp control clockwise to the second position to
turn on the headlamps. Pull the headlamp control towards you to
turn on the foglamps. Must be in autolamp mode, parklamp
position or headlamp position for foglamps to operate. Rotate
the control counterclockwise to initiate the autolamps. (This light
sensitive system turns your exterior lamps on and off automatically.
It also keeps the lights on for approximately 20 seconds after the
ignition switch is turned to the OFF position.) To turn the system off,
rotate the control clockwise to the OFF position.
3 ABS Light
Your antilock braking system (ABS) detects the onset of wheel lockup
during brake applications and helps prevent wheels from locking
during extreme braking situations. The ABS warning light will
illuminate when you start your engine; however, if it stays on,
continues to flash or fails to illuminate, see your dealership's service
department immediately.
5Speed Control
You must be traveling at or above 30 miles per hour to use the
speed control system. Press ON to enable speed control. Press
SET + to set a speed. To set a higher speed, accelerate to the
desired speed, press and release SET +. To establish a lower
speed, press and hold the SET control until you get to the desired
speed, then release the control or depress the brake pedal or
press CNCL until the desired vehicle speed is reached then press
the SET + control. To return to a previously set speed, press RES.
To disengage speed control and erase the previously programmed
set speed, press OFF.
6Audio System
Please see Audio System on the reverse side of this guide.
7Climate Control
Please see Climate Control on the reverse side of this guide.
4Service Engine Soon
This light will illuminate briefly when you start your vehicle to ensure
that the engine warning system is functional. If it comes on after the
engine is started, one of your engine’s emission control systems
may be malfunctioning. Or, it may stay on because your vehicle is out
of fuel, existing fuel quality is poor, or the fuel cap hasn’t been
properly tightened. If you have added high quality fuel or tightened
the fuel cap and the light continues to stay on, remember that it can
take three driving cycles for the light to turn off. (A driving cycle
consists of a cold engine startup followed by mixed city/highway
driving.) No additional vehicle service would be required.