low beam LINCOLN CONTINENTAL 1997 Owners Manual

261
The driving modes required to reach the ready
condition consist of a minimum of 30 minutes of
city and highway driving as described below:q
At least twenty minutes driving in stop and go,
city type traffic with at least four idle periods.
q
At least ten minutes of driving on an
expressway or highway.
Before completing the above driving modes, the
engine must be warmed up and at operating
temperature. Once started, the vehicle must not be
turned off during these driving modes.
Lights and Bulb ReplacementIt is a good idea to check the operation of the
following lights frequently:q
headlamps
q
high-mount brakelamp
q
tail lamps
q
brakelamps
q
hazard flasher
q
turn signals
q
side markers
q
license plate lamps
The alignment of your headlamps should be
checked if:
q
oncoming motorists frequently signal you to turn
off your vehicle's high beams when you do not
have the high beams on
q
the headlamps do not seem to give you enough
light to see clearly at night
q
the headlamp beams are pointed substantially
away from a position slightly down and to the
right
File:11fnmcc.ex
Update:Fri Sep 6 08:51:16 1996

2645. Hold the headlamp assembly snugly against the
vehicle and push down on the right angle
brackets to lock the lamp into position.
6. Install the plastic sight shield.
7. Turn the headlamps on and make sure that
they work properly. If the headlamp was
correctly aligned before you changed the bulb,
you should not need to align it again.Aiming HeadlampsYour vehicle is equipped with a Vehicle Headlamp
Aim Device (VHAD) on each headlamp body. Each
headlamp may be properly aimed in the horizontal
direction (left/right) and the vertical position
(up/down).NOTE:A non-zero bubble reading does not
necessarily indicate out-of-aim headlamps. If your
vehicle is not positioned on a level surface, the
slope will be included in the level indicator.
Therefore, vertical headlamp adjustment should be
performed only when beam direction appears to be
incorrect or a level surface can be verified.
Tools required: One 4mm socket and ratchet.
The Horizontal aim must be adjusted first.
NOTE:The following procedure assumes that the
vehicle's front structure is in factory alignment
condition. If the vehicle has been in an accident
requiring the front end of the vehicle to be
repaired, the horizontal indicator should be
recalibrated by the servicing facility.
File:11fnmcc.ex
Update:Fri Sep 6 08:51:16 1996

315
J
Jack................. 206
operation...........207, 208
positioning..........207, 208
storage............... 206
Jump-starting your vehicle
attaching cables........... 214
disconnecting cables......... 216
K
Keyless entry system
locking and unlocking doors...... 119
programming entry code....... 121
Keys
key in ignition chime......... 63
positions of the ignition........ 62
removing from the ignition...... 63
stuck in lock position........62,63
L
Lamps
autolamp delay system........ 57
checking.............. 261daytime running light system..... 56
flashing the lamps.......... 65
hazard flashers............ 68
headlamps.............. 57
high beams............. 65
interior lamps............ 56
replacing bulbs............ 261
trailer............... 188
Lane change indicator
(see Turn signal)......... 64,65
Lap belts............... 141
Lights, warning and indicator
airbag............... 15
anti-lock brakes (ABS)......... 11
anti-theft.............. 16
brake................ 10
charging system........... 13
engine oil pressure.......... 12
hazard warning light......... 68
high beam............. 15
lowoil............... 12
oil pressure............. 12
File:fnixc.ex
Update:Tue Sep 17 08:28:54 1996