homelink LINCOLN CONTINENTAL 2017 Owners Manual

HomeLink Wireless Control System
WARNINGS
Make sure that the garage door and
security device are free from
obstruction when you are programming. Do
not program the system with the vehicle in
the garage. Do not use the system with any garage
door opener that does not have the
safety stop and reverse feature as required
by U.S. Federal Safety Standards (this
includes any garage door opener
manufactured before April 1, 1982). A garage
door opener which cannot detect an object,
signaling the door to stop and reverse, does
not meet current federal safety standards.
Using a garage door opener without these
features increases the risk of serious injury
or death. Note:
Make sure you keep the original
remote control transmitter for use in other
vehicles as well as for future system
programming. Note:
We recommend that upon the sale or
lease termination of your vehicle, you erase
the programmed function buttons for security
reasons. See Erasing the Function Button
Codes later in this section.
Note: You can program a maximum of three
devices. To change or replace any of the
three devices after it has been initially
programmed, you must first erase the current
settings. See
Erasing the Function Button
Codes. The universal garage door opener replaces
the common hand-held garage door opener
with a three-button transmitter integrated
into the driver’
s sun visor. The system includes two primary features, a
garage door opener and a platform for
remote activation of devices within the home.
You can program garage doors as well as
entry gate operators, security systems, entry
door locks and home or office lighting.
Additional system information can be found
online at www.homelink.com,
www.youtube.com/user/HomeLinkGentex
or by calling the toll-free help line at
1-800-355-3515.
In-Vehicle Programming
This process is to program your in-vehicle
HomeLink function button with your
hand-held transmitter.
Note:
The programming steps below assume
you will be programming HomeLink that was
not previously programmed. If your
HomeLink was previously programmed, you
may need to erase your HomeLink buttons.
See
Erasing the Function Button Codes.
Note: Put a new battery in the hand-held
transmitter. This helps ensure quicker
training and accurate transmission of the
radio-frequency signal.
164
Continental (CPL) Canada/United States of America, enUSA, First Printing Universal Garage Door OpenerE188211

1. With your vehicle parked outside of the
garage, switch your ignition to the on
position, but do not start your vehicle.
2. Press and release the function button that you would like to program.
3. Hold your hand-held garage door transmitter 1–3 in (2–8 cm) away from the
HomeLink button you want to program.
4. Press and hold the hand-held transmitter
button you want to program while
watching the indicator light on HomeLink.
Continue to hold the hand-held button
until the HomeLink indicator light flashes
rapidly or is continuously on. Note:
You may need to use a different
method if you live in Canada or have
difficulties programming your gate operator
or garage door opener. See Gate Operator
/ Canadian Programming.
5. Press and hold the HomeLink button you
programmed for two seconds, then
release. You may need to do this twice
to activate the door. If your garage door
does not operate, watch the HomeLink
indicator light.
If the indicator light stays on, the
programming is complete. Your device
should activate when the HomeLink button
is pressed and released.
If the indicator light flashes rapidly, press and
hold for two seconds and release the
programmed HomeLink button. Repeat the
"press/hold/release" sequence up to three
times to complete the programming process.
If your device still does not operate, you must
program your garage door. See
Programming Your Garage Door Opener
Motor.
To program additional buttons, repeat Steps
1 – 4. For questions or comments, please contact
HomeLink at www.homelink.com,
www.youtube.com/user/HomeLinkGentex
or by calling the toll-free help line at
1-800-355-3515.
Programming Your Garage Door Opener
Motor
Note:
You may need a ladder to reach the
unit and you may need to remove the cover
or lamp lens on your garage door opener. 1. Press the learn button on the garage
door opener motor and then you have
30 seconds to complete the next two
steps.
2. Return to your vehicle.
165
Continental (CPL) Canada/United States of America, enUSA, First Printing Universal Garage Door OpenerE188212 E142659

3. Press and hold the function button you
want to program for 2 seconds, then
release. Repeat this step. Depending on
your brand of garage door opener, you
may need to repeat this sequence a third
time. Gate Operator / Canadian Programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit) after
several seconds of transmission – which may
not be long enough for HomeLink to pick up
the signal during programming. Similar to
this Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
Note:
If programming a garage door opener
or gate operator, it is advised to unplug the
device during the “cycling” process to
prevent possible overheating.
1. Press and release, every two seconds,
your hand-held transmitter until the
HomeLink indicator light changes to a
rapidly blinking or continuously on light.
2. Release the hand-held transmitter button.
3. Continue programing HomeLink. See In-Vehicle Programming, Step 4
.
Erasing the Function Button Codes
Note: You cannot erase individual buttons. 1. Press and hold the outer two function
buttons simultaneously for approximately
10 seconds until the indicator light above
the buttons flashes rapidly.
2. When the indicator light flashes, release
the buttons. You erased the codes for all
buttons.
Reprogramming a Single Button
To program a device to a previously trained
button, follow these steps:
1. Press and hold the desired button. Do NOT release the button.
166
Continental (CPL) Canada/United States of America, enUSA, First Printing Universal Garage Door OpenerE188212 E188213

2. The indicator light begins to flash after
20 seconds. Without releasing the
button, follow Step 1 in the Programming
section.
For questions or comments, contact
HomeLink at www.homelink.com,
www.youtube.com/user/HomeLinkGentex
or by calling the toll-free help line at
1-800-355-3515.
FCC and RSS-210 Industry Canada
Compliance
This device complies with Part 15 of the FCC
Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
Note: Changes or modifications to your
device not expressly approved by the party
responsible for compliance can void the
user’ s authority to operate the equipment. This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. End Users must follow the
specific operating instructions for satisfying
RF exposure compliance. This transmitter
must be at least 8 in (20 cm) from the user
and must not be co-located or operating in
conjunction with any other antenna or
transmitter.
The term “IC:” before the
certification/registration number only signifies
that Industry Canada technical specifications
were met.
167
Continental (CPL) Canada/United States of America, enUSA, First Printing Universal Garage Door Opener

The Better Business Bureau (BBB) Auto
Line Program (U.S. Only)...........................281
Tire Care..........................................................341 Glossary of Tire Terminology..........................342
Important Information About Low-Profile
Tires....................................................................341
Information About Uniform Tire Quality Grading..............................................................341
Information Contained on the Tire Sidewall............................................................343
Temperature A B C.............................................342
Traction AA A B C...............................................342
Treadwear..............................................................341
Tire Pressure Monitoring System.............356 Changing Tires With a Tire Pressure
Monitoring System.........................................357
Understanding Your Tire Pressure Monitoring System .............................................................358
Tires See: Wheels and Tires.......................................341
Towing a Trailer.............................................263
Load Placement..................................................263
Towing the Vehicle on Four Wheels........267 Emergency Towing.............................................267
Recreational Towing..........................................267
Towing.............................................................263
Traction Control
............................................207
Principle of Operation.......................................207 Transmission Code Designation...............377
Transmission...................................................187
Transmission
See: Transmission................................................187
Transporting the Vehicle.............................277
U
Under Hood Overview - 2.7L EcoBoost™/ 3.7L
................................................................308
Under Hood Overview - 3.0L EcoBoost™.....................................................310
Universal Garage Door Opener
................164
HomeLink Wireless Control System...............164
USB Port
..........................................................401
Using Adaptive Cruise Control.................230
Automatic Cancellation.....................................235
Blocked Sensor...................................................237
Canceling the Set Speed.................................235
Changing the Set Speed..................................235
Detection Issues.................................................235
Following a Vehicle............................................232
Following a Vehicle to a Complete
Stop...................................................................233
Hilly Condition Usage.......................................235
Overriding the Set Speed................................234
Resuming the Set Speed..................................235
Setting the Adaptive Cruise Speed................231 Setting the Adaptive Cruise Speed When Your
Vehicle is Stationary......................................232
Setting the Gap Distance.................................
233
Switching Adaptive Cruise Control Off.........235
Switching Adaptive Cruise Control On..........231
Switching to Normal Cruise Control..............238
System Not Available........................................237
Using All-Wheel Drive
..................................192
Driving In Special Conditions With All-Wheel
Drive (AWD)......................................................194
Operating AWD Vehicles With Spare or Mismatched Tires...........................................194
Using Cruise Control...................................229 Switching Cruise Control Off...........................230
Switching Cruise Control On...........................229
Using MyKey With Remote Start Systems..........................................................63
Using Snow Chains......................................355
Using Stability Control
.................................210
Using Summer Tires....................................354
Using Traction Control................................207 Switching the System Off.................................207
System Indicator Lights and Messages........207
Using a Switch.....................................................207
Using the Information Display Controls........
207
Using Voice Recognition.............................419 Audio Voice Commands....................................421
Climate Voice Commands...............................
422
580
Continental (CPL) Canada/United States of America, enUSA, First Printing Index