bulb LINCOLN MKZ 2008 User Guide

4. Remove the bulb socket by
rotating it counterclockwise, then
pulling it out of the lamp assembly.
5. Let go of the bulb socket and
leave it dangling near the lamp
housing.
6. Reach over the front bolster in
the engine area, with a tool if
necessary, bring the bulb socket
upwards into an unobstructed area to replace the bulb.
7. Carefully pull bulb straight out of
socket and push in the new one.
8. After the new bulb is installed,
carefully let the bulb socket dangle
downward near the lamp housing.
9. From the exterior wheel well area
reach arm through splash shield
opening to install bulb socket with
new bulb.
10. Install the new bulb socket into the lamp assembly by aligning the
indexing fingers, then rotate clockwise to locked position.
11. Reinstall splash shield with screw.
12. Reinstall Air Tube to the air filter assembly (Driver’s Side Only).
Replacing primary park/turn signal bulbs
1. Make sure headlamp switch is in the OFF position, then open the
hood.
2. Reach over the front bolster.
3. Disengage top of flexible washer
bottle filler neck from snap strap
attachment and position it to gain
access path to the high beam bulb
(Passenger Side Only).
2008 MKZ(378)
Owners Guide (post-2002-fmt)
USA(fus)
Lights
47

4. Remove the bulb socket by
rotating it counterclockwise, then
pulling it straight out of the lamp
assembly.
5. Discard the old bulb and install
the new bulb into bulb socket.
6. Install the new bulb socket into
the lamp assembly by aligning the
indexing fingers, then rotate
clockwise to locked position.
7. If required, position the flexible
washer bottle filler neck back to its
original position and connect the snap strap (Passenger side only).
8. If required, reinstall the AirTube to the air filter assembly. (Driver’s
side only).
Replacing stop/tail/turn and side marker bulbs
Your vehicle is equipped with a rear lamp that has a stop/tail/turn and
side marker lamp module containing integral multiple light emitting
diodes (LED). If one or more LEDs burn out, the complete lamp module
has to be replaced. See your authorized dealer for the replacement LED
module.
Replacing rear turn signal bulbs
1. Make sure the headlamp switch is in the OFF position and open the
trunk.
2. Lift out trunk floor carpeting panel to access a Luggage Scuff Plate
(Hard Molding) shingles and a Trunk Side Panel (dark grey, soft
wheelhouse side trim panel) at the lamp area.
3. Carefully pull/push the Trunk Side Panel (dark grey, soft wheelhouse
side trim panel) outboard to expose the lamp assembly. The most
effective point to grasp the Trunk Side Panel when pulling it out from
the Luggage Scuff Plate is at it’s bottom edge where that edge meets the
exposed sheet metal of the trunk floor.
2008 MKZ(378)
Owners Guide (post-2002-fmt)
USA(fus)
Lights
48

Note:Do not allow the Trunk Side Panel to remain bent and untucked
from the Luggage Scuff Plate (hard molding) for a long period of time.
Doing so may result in permanent deformation.
4. Remove the bulb socket by
rotating it counterclockwise, then
pulling it out of the lamp assembly.
5. Pull the bulb from the socket and
push in the new bulb.
6. Install the bulb socket into the
lamp assembly by rotating it
clockwise.
7. Carefully push the Trunk Side
Panel (dark grey, soft wheelhouse
side trim panel) back to the shingle position to the Luggage Scuff Plate
(hard molding).
8. Install trunk floor carpeting panel.
Replacing backup lamp/redundant tail lamp bulbs
The backup lamp and redundant tail lamp bulbs are located in the trunk
lid. Follow the same steps to replace either bulb.
1. Make sure headlamp switch is in
OFF position and open trunk to
access the lamp assembly.
2. Position the decklid trim aside by
removing 3 to 4 pin-type retainers
to expose the lamp assembly.
3. Remove the bulb socket by
rotating it counterclockwise, then
pulling it out of the lamp assembly.
4. Pull the bulb from the socket and
push in the new bulb.
5. Install the bulb socket into the
lamp assembly by rotating it
clockwise.
6. Carefully reposition the trim back
to its original position and secure
the retainers.
2008 MKZ(378)
Owners Guide (post-2002-fmt)
USA(fus)
Lights
49

Replacing high-mount brake lamp bulb
1. Make sure the ignition control is
in the LOCK (OFF) position.
2. Open the trunk and reach
underneath package tray to locate
lamp assembly.
3. Remove the bulb socket by
rotating it counterclockwise, then
pulling it out of the lamp assembly.
4. Pull the bulb straight from the
socket and push in the new bulb.
5. Install the bulb socket into the lamp assembly by rotating it clockwise.
Replacing license plate lamp bulbs
1. Make sure the headlamp switch is
in the OFF position.
2. Remove the two screws from the
license plate lamp assembly.
3. Remove bulb socket by turning
counterclockwise.
4. Carefully pull the bulb out from
the socket.
Install new bulb(s) in reverse order.
Replacing fog lamp bulbs
1. Make sure the fog lamp switch is
in the OFF position.
2. From underneath the vehicle,
partially remove the tire splash
shield by removing four drive
screws.
After removing to allow free access
to the front fog lamp bulb and
electrical wire harness, the splash shield flap should be able to be
repositioned.
2008 MKZ(378)
Owners Guide (post-2002-fmt)
USA(fus)
Lights
50

3. Rotate the harness/bulb assembly
counterclockwise, to remove from
the fog lamp.
4. Carefully disconnect the bulb
from the harness assembly via the
two snap clips.
Install the new bulb in reverse order.
2008 MKZ(378)
Owners Guide (post-2002-fmt)
USA(fus)
Lights
51

CHECK LEFT OR RIGHT HEADLAMPS (if equipped).Displayed
when the headlamps are activated and at least one low beam is burned
out. This warning will not display for the optional HID low beam bulb.
Check the lamps as soon as possible and have the burned out lamp
replaced. Refer toReplacing headlamp bulbsin theLightschapter.
CHECK LF OR RF TURN LAMPS.Displayed when the turn signals are
activated and at least one is burned out. Check the lamps as soon as
safely possible and have the burned out lamp replaced. Refer to
Replacing headlamp bulbsin theLightschapter.
CHECK LR OR RR TURN LAMPS.Displayed when the rear turn
signals are activated and at least one is burned out. Check the lamps as
soon as safely possible and have the burned out lamp replaced. Refer to
Replacing headlamp bulbsin theLightschapter.
INTEGRATED KEY PROGRAMMING STATUS.Displayed when an
attempt is made to program a fifth Integrated Key to the Remote Key
Entry System. For more information on Integrated Key, refer toLocks
and Securitychapter in this manual.
INTERIOR TRUNK CONTROL
Press the remote trunk release
control on the instrument panel to
the left of the steering wheel.
2008 MKZ(378)
Owners Guide (post-2002-fmt)
USA(fus)
Driver Controls
78

3. The fuel cap may not have been securely tightened. SeeFuel filler
capin this chapter.
4. Driving through deep water—the electrical system may be wet.
These temporary malfunctions can be corrected by filling the fuel tank
with good quality fuel, properly tightening the fuel cap or letting the
electrical system dry out. After three driving cycles without these or any
other temporary malfunctions present, theService engine soon
indicator should stay off the next time the engine is started. A driving
cycle consists of a cold engine startup followed by mixed city/highway
driving. No additional vehicle service is required.
If theService engine soon
indicator remains on, have your vehicle
serviced at the first available opportunity. Although some malfunctions
detected by the OBD-II may not have symptoms that are apparent,
continued driving with theService engine soon
indicator on can
result in increased emissions, lower fuel economy, reduced engine and
transmission smoothness, and lead to more costly repairs.
Readiness for Inspection/Maintenance (I/M) testing
Some state/provincial and local governments may have
Inspection/Maintenance (I/M) programs to inspect the emission control
equipment on your vehicle. Failure to pass this inspection could prevent
you from getting a vehicle registration. Your vehicle may not pass the I/M
test if theService engine soon
indicator is on or not working
properly (bulb is burned out), or if the OBD-II system has determined
that some of the emission control systems have not been properly
checked. In this case, the vehicle is considered not ready for I/M testing.
If theService engine soon
indicator is on or the bulb does not
work, the vehicle may need to be serviced. Refer to the On board
diagnostics (OBD-II) description in this chapter.
If the vehicle’s engine or transmission has just been serviced, or the
battery has recently run down or been replaced, the OBD-II system may
indicate that the vehicle is not ready for I/M testing. To determine if the
vehicle is ready for I/M testing, turn the ignition key to the ON position
for 15 seconds without cranking the engine. If theService engine
soon
indicator blinks eight times, it means that the vehicle is not
ready for I/M testing; if theService engine soon
indicator stays on
solid, it means that the vehicle is ready for I/M testing.
2008 MKZ(378)
Owners Guide (post-2002-fmt)
USA(fus)
Maintenance and Specifications
261

A
Accessory delay ..........................58
Air cleaner filter ...............265–267
Air conditioning ....................31, 33
Airbag supplemental
restraint system ........125, 134, 137
and child safety seats ............127
description ..............125, 134, 137
disposal ....................................140
driver airbag ............127, 135, 138
indicator light .........134, 136, 140
operation .................127, 135, 138
passenger airbag .....127, 135, 138
side airbag ...............................134
All Wheel Drive (AWD),
driving off road .........................193
Antifreeze
(see Engine coolant) ................245
Anti-lock brake system
(see Brakes) ......................184–185
Anti-theft system ................96, 100
arming the system ..................100
disarming a triggered
system .....................................101
Audio system (see Radio) .........16
Automatic transmission
driving an automatic
overdrive .................................189
fluid, adding ............................263
fluid, checking ........................263
fluid, refill capacities ..............268
fluid, specification ..................268
Auxiliary input jack (Line in) ....23
Axle
lubricant specifications ..........268
B
Battery .......................................243acid, treating emergencies .....243
jumping a disabled battery ....214
maintenance-free ....................243
replacement, specifications ...267
servicing ..................................243
Belt-Minder
.............................120
Booster seats .............................141
Brakes ........................................184
anti-lock ...........................184–185
anti-lock brake system (ABS)
warning light ...........................185
fluid, checking and adding ....263
fluid, refill capacities ..............268
fluid, specifications .................268
lubricant specifications ..........268
parking ....................................185
shift interlock ..........................188
Break-in period .............................5
Bulbs ............................................42
C
Capacities for refilling fluids ....268
Cell phone use ..............................7
Changing a tire .........................208
Child safety restraints ..............141
child safety belts ....................141
Child safety seats ......................144
attaching with tether straps ..148
in front seat ............................145
in rear seat ..............................145
Child safety seats - booster
seats ...........................................141
Cleaning your vehicle
engine compartment ..............230
instrument panel ....................231
interior .....................................232
plastic parts ............................230
2008 MKZ(378)
Owners Guide (post-2002-fmt)
USA(fus)
Index
275

Fluid capacities .........................268
Foglamps .....................................38
Four-Wheel Drive vehicles
driving off road .......................193
Fuel ............................................251
calculating fuel
economy ............................71, 256
cap ...........................................253
capacity ...................................268
choosing the right fuel ...........254
comparisons with EPA fuel
economy estimates .................259
detergent in fuel .....................255
filling your vehicle
with fuel ..................251, 253, 256
filter, specifications ........251, 267
fuel pump shut-off switch .....201
improving fuel economy ........256
octane rating ...................255, 270
quality ......................................255
running out of fuel .................255
safety information relating to
automotive fuels .....................251
Fuel pump shut-off switch .......201
Fuses ..................................201–202
G
Gas cap (see Fuel cap) ............253
Gas mileage
(see Fuel economy) .................256
Gauges .........................................14
H
Hazard flashers .........................200
Head restraints .........................102
Headlamps ...................................37
aiming ........................................40autolamp system .......................37
bulb specifications ....................42
daytime running lights .............38
flash to pass ..............................39
high beam .................................39
replacing bulbs .........................43
turning on and off ....................37
Heating
heating and air conditioning
system .................................31, 33
Homelink wireless control
system ..........................................66
Hood ..........................................236
I
Ignition ...............................179, 270
Illuminated visor mirror .............53
Infant seats
(see Safety seats) .....................144
Inspection/maintenance (I/M)
testing ........................................261
Instrument panel
cleaning ...................................231
cluster ........................................10
lighting up panel and
interior .......................................39
J
Jack ............................................208
positioning ...............................208
storage .....................................208
Jump-starting your vehicle ......214
K
Keyless entry system .................94
autolock .....................................82
keypad .......................................95
2008 MKZ(378)
Owners Guide (post-2002-fmt)
USA(fus)
Index
277

locking and unlocking doors ....96
programming entry code .........95
Keys .......................................79, 98
positions of the ignition .........179
L
Lamps
autolamp system .......................37
bulb replacement
specifications chart ..................42
daytime running light ...............38
fog lamps ...................................38
headlamps .................................37
headlamps, flash to pass ..........39
instrument panel, dimming .....39
interior lamps ...........................41
replacing bulbs .........................43
Lane change indicator
(see Turn signal) ........................41
Lights, warning and indicator ....10
anti-lock brakes (ABS) ..........185
Load limits .................................172
Locks
autolock .....................................82
childproof ..................................86
doors ..........................................81
Lubricant specifications ...........268
Lug nuts ....................................213
Lumbar support, seats .............105
M
Message center .....................69–70
english/metric button ...............74
system check button ................74
warning messages .....................75
Mirrors ...................................58–59automatic dimming rearview
mirror ........................................58
heated ........................................60
programmable memory ............90
side view mirrors (power) .......59
Moon roof ..............................64, 89
Motorcraft parts ........233, 251, 267
N
Navigation system .......................30
O
Octane rating ............................255
Oil (see Engine oil) ..................239
P
Parking brake ............................185
Parts (see Motorcraft parts) ....267
Passenger Occupant
Classification Sensor .................113
Power distribution box
(see Fuses) ...............................205
Power door locks ........................81
Power mirrors .............................59
Power point .................................55
Power steering ..........................187
fluid, checking and adding ....262
fluid, refill capacity ................268
fluid, specifications .................268
Power Windows ...........................56
Power windows
opening using remote entry
system .......................................89
R
Radio ............................................16
2008 MKZ(378)
Owners Guide (post-2002-fmt)
USA(fus)
Index
278