keyless LINCOLN TOWN CAR 1997 Owners Manual

97
To set the childproof lock on each rear door, open
the rear door.
Find the lever at the black label with the word
LOCKED in white letters. Move the lever up.
To release the childproof lock, open the rear door
from the outside and move the lever down.Using the Power Door LocksYour vehicle has power door locks. The controls to
lock the doors are on the trim panel of the front
door. When you close the doors after you set the
door locks, the doors remain locked. If the power
mechanism ever fails, the manual door lock will
override the power controls.The power locks on the driver's door
Illuminated Entry System with Theater
LightingThe interior lights will illuminate for approximately
25 seconds when any button on the keyless entry
pad is pressed or the remote entry system UNLOCK
button is pushed.
File:05fncft.ex
Update:Mon Jun 17 13:49:49 1996

106The keyless entry buttonsWhen you bought your vehicle, you were given a
computer code that operates the system for your
vehicle. For your convenience, we have duplicated
this code in three places.The code is:
q
on your owner's wallet card found in the glove
compartment
q
taped to the trunk lid's right hinge support bar
q
taped to the computer module in your driver's
front door
When you use keyless entry, the illuminated entry
system turns on the interior lights for 25 seconds
and the buttons on the keypad light up. Do not
push the buttons with a key, ballpoint pen, pencil,
or any other hard object. These objects could
damage the buttons.
File:05fncft.ex
Update:Mon Jun 17 13:49:49 1996

107
Unlocking the Doors with the Keyless
Entry SystemYou must unlock the driver's door before you
unlock any of the other doors or trunk. If you let
more than five (5) seconds pass before pressing
numbers, the system shuts down, and you have to
enter the code again. The system has shut down if
the keypad light is out. If the keyless entry system
does not work properly, use the key or
transmitter(s) to lock and unlock the doors or
unlock the trunk.
1. To unlock the driver's door, enter the factory
code or your personal code. All codes have five
(5) numbers. After you press the fifth number,
the driver's door unlocks.
2. To unlock all passenger doors, press the 3/4
button within five (5) seconds of unlocking the
driver's door or trunk, or re-enter the code to
open the driver's door, then press 3/4.3. To unlock the trunk, press the 5/6 button
within five seconds of unlocking the driver's or
passenger's doors, or re-enter the code to open
the driver's door, then press 5/6.
As long as the driver's door has been unlocked first,
you can open the passenger door or the trunk in
any order.
Locking the Doors with the Keyless
Entry SystemAlong with unlocking your doors, you can use the
keyless entry system to lock the doors.
To lock all of the vehicle's doors at the same time,
press 7/8 and 9/0 at the same time. It is not
necessary to first enter the keypad code. This will
also arm your anti-theft system (if equipped).
File:05fncft.ex
Update:Mon Jun 17 13:49:49 1996

108AutolockThe Autolock feature will automatically lock all the
doors when:q
the vehicle's doors are fully closed
q
the ignition key is turned to the ON position
q
someone is sitting in the driver's seat or a
heavy object is placed on it
q
the vehicle is in any forward or reverse gear.
The Autolock feature will repeat when:
q
the ignition key remains in the ON position
q
someone remains sitting in the driver's seat or a
heavy object is on the seat
q
a door is opened and then closed
q
the vehicle is in any forward or reverse gear.If you do not want to use the Autolock feature, it
can be deactivated by using the buttons for the
keyless entry system.
To deactivate the Autolock system:
1. Enter your permanent five-digit entry code (not
the personal code you may have set).
2. Within 5 seconds, press and hold 7/8.
3. Within 5 more seconds, press and release 3/4.
4. Release 7/8.
To reactivate the Autolock feature, simply repeat
the instructions for deactivating the system. The
Autolock feature can be turned on and off using the
instructions above.
File:05fncft.ex
Update:Mon Jun 17 13:49:49 1996

109
Programming Your Own Entry CodeYou can program up to four (4) personal codes to
unlock your vehicle. This code does not replace the
permanent code that the dealership gave you. Use
your personal code in the same manner as you
would your original code.
To program your own code:
1. Select five digits for your personal code.
2. Enter the factory code that the dealership gave
you.
3. Within five (5) seconds, press 1/2.
4. Within five (5) seconds of pressing 1/2, enter
your personal code, pressing each digit within
five (5) seconds of the previous digit.5. Enter a sixth digit to indicate which memory
should be recalled by this personal code.
1/2 Recall Memory 1
3/4 Recall Memory 2
5/6 Recall Memory 3
9/0 No recall
All of the vehicle doors will lock and then
unlock to confirm programming of the new
code.
The keyless entry system registers this new code.
To open your vehicle, you can now use either code.
File:05fncft.ex
Update:Mon Jun 17 13:49:49 1996

110To erase all of the personal entry codes and remote
entry transmitters programmed to a vehicle:
1. Enter the original permanent code.
2. Press 1/2 within five seconds of Step 1.
3. Press and hold 1/2 for two (2) seconds.
All of the vehicle doors will lock and then
unlock to confirm erasure.
Do not set a code that presents the numbers in
sequential order, such as 1/2, 3/4, 5/6, 7/8, 9/0.
Studies show that people who idly press the buttons
usually press a sequential pattern. Also, do not
select a code that uses the same button five times.
Thieves can easily figure out these types of codes.
Arming, disarming and resetting your
anti-theft system from the keyless entry
padThe Keyless Entry system will arm the anti-theft
system when you use the 7/8 and 9/0 keys to lock
the doors, and will disarm or reset a triggered
anti-theft alarm when you enter in the five digit
code to unlock the driver's door.Remote Entry SystemWith the remote entry system, you can lock and
unlock the vehicle doors and open the trunk
without using a key. The buttons for the system are
located on the two hand held transmitters that
came with your vehicle. The remote also has a
personal alarm feature.
The system will work with up to four transmitters.
Your vehicle came with two transmitters. Additional
transmitters can be ordered from your dealer.
File:05fncft.ex
Update:Mon Jun 17 13:49:49 1996

113
Memory Seat and Mirror Featureq
Remote Entry
Pressing the UNLOCK button on the remote
entry key fob unlocks the driver's door and
recalls all of the Memory settings. Two key fobs
are delivered with the vehicle. One is
programmed to always recall Memory 1 and the
other will always recall Memory 2. Memory 1
or 2 is indicated on the back of the key fob.
Memory recall from the remote key fob can be
disabled. This is done by sliding the switch on
the back of the key fob to OFF. Memory can
still be recalled using the keyless entry code or
the Memory 1 or Memory 2 switches.
q
Keyless Entry
Up to four unique keyless entry codes can be
programmed by the customer. Three of the
codes can be assigned to recall Memory 1,
Memory 2, or Memory 3. Each time the
five-digit code is entered on the keypad, the
driver's door will unlock and Memory 1,
Memory 2, or Memory 3 will be recalled.
q
Memory Switches
Pressing either the Memory 1 or Memory 2
switch on the driver's door will also recall the
memory settings as selected.
File:05fncft.ex
Update:Mon Jun 17 13:49:49 1996

114Replacing the BatteriesThe remote entry transmitter is powered by two
coin type three-volt lithium 1616 batteries
(included) that should last for several years of
normal use. If you notice a significant decrease in
operating range, the batteries should be replaced.
Replacement batteries can be purchased at most
pharmacies, watch stores or at your Ford or
Lincoln-Mercury dealer.
NOTE:The operating range of the remote entry
system can also be affected by weather conditions
(such as very cold temperatures) or structures
around the vehicle (buildings, other vehicles, radio
and TV towers, etc.). Typical operating range will
allow you to be up to 33 feet (10 meters) away
from your vehicle.
The transmitter can be snapped apart to replace the
batteries by twisting a thin coin between the two
halves of the transmitter. DO NOT TAKE THE
FRONT PART OF THE TRANSMITTER APART.When installing the new batteries, be sure to place
the positive (+) side down as marked. Snap the two
halves back together.
Replacement/additional transmittersIn the event a transmitter is lost, a new one may
be purchased from your dealer. To program the
new transmitter:
Additional transmitters may be purchased from your
dealer (remote entry system will work with up to
four transmitters). To program additional
transmitters to your vehicle, use the following
procedure for replacement transmitters.
1. Enter the factory keyless entry code. Your
personal code will not allow programming.
2. Press the 1/2 button.
File:05fncft.ex
Update:Mon Jun 17 13:49:49 1996

115
3. Press one button on each of the transmitters to
be programmed. Each transmitter button must
be pressed within seven (7) seconds of the
prior one. Each time a transmitter is
successfully programmed, all of the vehicle
doors will lock and then unlock to verify
programming. If the doors did not lock/unlock,
your transmitter was not programmed.
THIS DEVICE COMPLIES WITH PART 15 OF
THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1)
THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
NOTE:All transmitters to be used on your vehicle
must be programmed/reprogrammed at the same
time.
Battery SaverWhen the ignition is turned off, the vehicle will
turn off battery voltage to the vehicle lamps as
follows:q
Courtesy lights (lights which come on when a
door is opened): after 10 minutes.
q
Map/Glove compartment/Trunk/Hook lamps:
after 30 minutes.
q
Headlamps and park lamps (only if headlamp
switch is left in the headlamp position): after 10
minutes.
This will prevent draining of the battery if those
lights have been left on inadvertently or if a door is
not completely closed. Battery voltage to these
lamps will be restored when the keyless entry
keypad is used, the remote entry transmitter is
used, any door is opened, the trunk is opened, or
the ignition key is turned to the ON position.
File:05fncft.ex
Update:Mon Jun 17 13:49:49 1996

117
3. Lock the doors by using the power door lock
switch, pressing the remote entry transmitter
LOCK button or pressing the last two buttons
(7/8, 9/0) of the keyless entry keypad.
The alarm indicator will now glow steadily.
4. Close all doors. The alarm indicator light will
then remain on steadily for approximately 30
more seconds and then go out. When the light
goes out the system is armed.
NOTE:Be sure to close all doors completely. If
not, the alarm indicator light will remain on.
Remember, your anti-theft system is armed only
after the alarm indicator light remains on steadily
for approximately 30 seconds after the last door is
closed, and then goes out.You can also arm the anti-theft system with the
factory installed remote entry system or the keyless
entry system by following this sequence:
1. Remove the key from the ignition.
2. Close all of the doors.
3. Press the remote entry transmitter LOCK
button or press the last two buttons (7/8, 9/0)
of the keyless entry keypad to lock the doors.
The alarm indicator will come on for 30
seconds to show the alarm is arming and then
turn off to show that the alarm has armed.
The anti-theft system is designed to work with the
factory installed remote entry system. It may not
work with other remote entry systems.
NOTE:The anti-theft system will not activate while
someone is sitting in the driver's seat or if there is
a heavy object in the driver's seat.
File:05fncft.ex
Update:Mon Jun 17 13:49:49 1996