check engine LINCOLN TOWN CAR 2010 Owner's Manual
[x] Cancel search | Manufacturer: LINCOLN, Model Year: 2010, Model line: TOWN CAR, Model: LINCOLN TOWN CAR 2010Pages: 285, PDF Size: 1.94 MB
Page 254 of 285

Refueling
WARNING:Fuel vapor burns violently and a fuel fire can cause
severe injuries. To help avoid injuries to you and others:
•Read and follow all the instructions on the pump island;
•Turn off your engine when you are refueling;
•Do not smoke if you are near fuel or refueling your vehicle;
•Keep sparks, flames and smoking materials away from fuel;
•Stay outside your vehicle and do not leave the fuel pump unattended
when refueling your vehicle — this is against the law in some places;
•Keep children away from the fuel pump; never let children pump
fuel.
Use the following guidelines to avoid electrostatic charge build-up when
filling an ungrounded fuel container:
•Place approved fuel container on the ground.
•DO NOT fill a fuel container while it is in the vehicle (including the
cargo area).
•Keep the fuel pump nozzle in contact with the fuel container while
filling.
•DO NOT use a device that would hold the fuel pump handle in the fill
position.
Fuel filler cap
When fueling your vehicle:
1. Turn the engine off.
2. Carefully turn the filler cap counterclockwise until it spins off.
3. Pull to remove the cap from the fuel filler pipe.
4. To install the cap, align the tabs on the cap with the notches on the
filler pipe.
5. Turn the filler cap clockwise until it clicks at least once.
If the check fuel cap light
or a CHECK FUEL CAP message comes
on, the fuel filler cap may not be properly installed. The light or message
can come on after several driving events after you’ve refueled your
vehicle.
At the next opportunity, safely pull off of the road, remove the fuel filler
cap, align the cap properly and reinstall it. The check fuel cap
Maintenance and Specifications
254
2010 Town Car(tow)
Owners Guide, 1st Printing
USA(fus)
Page 255 of 285

lightor CHECK FUEL CAP message may not reset immediately; it
may take several driving cycles for the check fuel cap light
or CHECK
FUEL CAP message to turn off. A driving cycle consists of an engine
start-up (after four or more hours with the engine off) followed by city
and highway driving.
Continuing to drive with the check fuel cap light
or CHECK FUEL
CAP message on may cause the
light to turn on as well.
If you must replace the fuel filler cap, replace it with a fuel filler
cap that is designed for your vehicle. The customer warranty may
be void for any damage to the fuel tank or fuel system if the
correct genuine Ford, Motorcraft or other certified fuel filler cap
is not used.
WARNING:The fuel system may be under pressure. If the fuel
filler cap is venting vapor or if you hear a hissing sound, wait
until it stops before completely removing the fuel filler cap. Otherwise,
fuel may spray out and injure you or others.
WARNING:If you do not use the proper fuel filler cap,
excessive vacuum in the fuel tank may damage the fuel system
or cause the fuel cap to disengage in a collision, which may result in
personal injury.
FFV (Flex Fuel Vehicle) fuel cap
If your vehicle is FFV capable, it will have a yellow colored fuel cap.
Choosing the right fuel
If your vehicle is a flexible fuel vehicle (FFV), use only UNLEADED
FUEL and FUEL ETHANOL (Ed75–Ed85).
If your vehicle is not a flexible fuel vehicle (FFV), then only use
UNLEADED fuel or UNLEADED fuel blended with a maximum of 10%
ethanol. Do not use fuel ethanol (E85), diesel, methanol, leaded fuel or
any other fuel.
The use of leaded fuel is prohibited by law and could damage your
vehicle.
Your vehicle was not designed to use fuel or fuel additives with metallic
compounds, including manganese-based additives.
Note:Use of any fuel other than those recommended may cause
powertrain damage, a loss of vehicle performance, and repairs may not
be covered under warranty.
Maintenance and Specifications
255
2010 Town Car(tow)
Owners Guide, 1st Printing
USA(fus)
Page 262 of 285

government emission standards. The OBD-II system also assists your
authorized dealer in properly servicing your vehicle. When the service
engine soon
indicator illuminates, the OBD-II system has detected
a malfunction. Temporary malfunctions may cause the service engine
soon
indicator to illuminate. Examples are:
1. The vehicle has run out of fuel—the engine may misfire or run poorly.
2. Poor fuel quality or water in the fuel—the engine may misfire or run
poorly.
3. The fuel cap may not have been securely tightened. SeeFuel filler
capin this chapter.
4. Driving through deep water—the electrical system may be wet.
These temporary malfunctions can be corrected by filling the fuel tank
with good quality fuel, properly tightening the fuel cap or letting the
electrical system dry out. After three driving cycles without these or any
other temporary malfunctions present, the service engine soon
indicator should stay off the next time the engine is started. A driving
cycle consists of a cold engine startup followed by mixed city/highway
driving. No additional vehicle service is required.
If the service engine soon
indicator remains on, have your vehicle
serviced at the first available opportunity. Although some malfunctions
detected by the OBD-II may not have symptoms that are apparent,
continued driving with the service engine soon
indicator on can
result in increased emissions, lower fuel economy, reduced engine and
transmission smoothness, and lead to more costly repairs.
Readiness for Inspection/Maintenance (I/M) testing
Some state/provincial and local governments may have
Inspection/Maintenance (I/M) programs to inspect the emission control
equipment on your vehicle. Failure to pass this inspection could prevent
you from getting a vehicle registration. Your vehicle may not pass the I/M
test if the service engine soon
indicator is on or not working
properly (bulb is burned out), or if the OBD-II system has determined
that some of the emission control systems have not been properly
checked. In this case, the vehicle is considered not ready for I/M testing.
If the service engine soon
indicator is on or the bulb does not
work, the vehicle may need to be serviced. Refer to the On board
diagnostics (OBD-II) description in this chapter.
If the vehicle’s engine or transmission has just been serviced, or the
battery has recently run down or been replaced, the OBD-II system may
Maintenance and Specifications
262
2010 Town Car(tow)
Owners Guide, 1st Printing
USA(fus)
Page 263 of 285

indicate that the vehicle is not ready for I/M testing. To determine if the
vehicle is ready for I/M testing, turn the ignition key to the on position
for 15 seconds without cranking the engine. If the service engine
soon
indicator blinks eight times, it means that the vehicle is not
ready for I/M testing; if the service engine soon
indicator stays on
solid, it means that the vehicle is ready for I/M testing.
The OBD-II system is designed to check the emission control system
during normal driving. A complete check may take several days. If the
vehicle is not ready for I/M testing, the following driving cycle consisting
of mixed city and highway driving may be performed:
15 minutes of steady driving on an expressway/highway followed by
20 minutes of stop-and-go driving with at least four 30-second idle
periods.
Allow the vehicle to sit for at least eight hours without starting the
engine. Then, start the engine and complete the above driving cycle. The
engine must warm up to its normal operating temperature. Once started,
do not turn off the engine until the above driving cycle is complete. If
the vehicle is still not ready for I/M testing, the above driving cycle will
have to be repeated.
POWER STEERING FLUID
Check the power steering fluid.
Refer toscheduled maintenance
information.
1. Start the engine and let it run until it reaches normal operating
temperature (the engine coolant temperature gauge indicator will be
near the center of the normal area between H and C).
2. While the engine idles, turn the steering wheel left and right several
times.
3. Turn the engine off.
Maintenance and Specifications
263
2010 Town Car(tow)
Owners Guide, 1st Printing
USA(fus)
Page 265 of 285

1. Drive the vehicle 20 miles (30 km) or until it reaches normal operating
temperature.
2. Park the vehicle on a level surface and engage the parking brake.
3. With the parking brake engaged and your foot on the brake pedal,
start the engine and move the gearshift lever through all of the gear
ranges. Allow sufficient time for each gear to engage.
4. Latch the gearshift lever in P (Park) and leave the engine running.
5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If
necessary, refer toIdentifying components in the engine compartment
in this chapter for the location of the dipstick.
6. Install the dipstick making sure it is fully seated in the filler tube.
7. Remove the dipstick and inspect the fluid level. The fluid should be in
the designated area for normal operating temperature or ambient
temperature.
Low fluid level
Do not drive the vehicle if the fluid
level is at the bottom of the dipstick
and the ambient temperature is
above 50°F (10°C).
Correct fluid level
The transmission fluid should be checked at normal operating
temperature 150°F-170°F (66°C-77°C) on a level surface. The normal
operating temperature can be reached after approximately 20 miles
(30 km) of driving.
You can check the fluid without driving if the ambient temperature is
above 50°F (10°C). However, if fluid is added at this time, an overfill
condition could result when the vehicle reaches normal operating
temperature.
The transmission fluid should be in
this range if at normal operating
temperature (150°F-170°F
[66°C-77°C]).
Maintenance and Specifications
265
2010 Town Car(tow)
Owners Guide, 1st Printing
USA(fus)
Page 274 of 285

The Vehicle Identification Number (VIN) contains the following
information:
1. World manufacturer identifier
2. Brake system / Gross Vehicle
Weight Rating (GVWR) / Restraint
Devices and their location
3. Make, vehicle line, series, body
type
4. Engine type
5. Check digit
6. Model year
7. Assembly plant
8. Production sequence number
TRANSMISSION CODE DESIGNATIONS
You can find a transmission code on
the Safety Compliance Certification
Label. The following table tells you
which transmission each code
represents.
Description Code
Four-speed automatic (4R75E) Q
Maintenance and Specifications
274
2010 Town Car(tow)
Owners Guide, 1st Printing
USA(fus)
Page 280 of 285

A
Accessory delay ..........................58
Air cleaner filter ...............267–268
Air suspension ...........................188
description ..............................188
Airbag supplemental restraint
system ........................116–117, 126
and child safety seats ............119
description ......................117, 126
disposal ....................................129
driver airbag ....................120, 127
indicator light .................126, 128
operation .........................120, 127
passenger airbag .............120, 127
side airbag ...............................126
Antifreeze
(see Engine coolant) ................245
Anti-lock brake system
(see Brakes) ......................184–185
Anti-theft system ..................89, 93
arming the system ....................94
disarming a triggered
system .......................................94
Audio system (see Radio) ...26, 31
Automatic transmission
driving an automatic
overdrive .................................190
fluid, adding ............................264
fluid, checking ........................264
fluid, refill capacities ..............269
fluid, specification ..................269
Auxiliary power point .................55
Axle
lubricant specifications ..........269
refill capacities ........................269
traction lok ..............................189B
Battery .......................................243
acid, treating emergencies .....243
jumping a disabled battery ....215
maintenance-free ....................243
replacement, specifications ...268
servicing ..................................243
Belt-Minder.............................112
Booster seats .............................144
Brakes ........................................184
anti-lock ...........................184–185
anti-lock brake system (ABS)
warning light ...........................185
fluid, checking and adding ....264
fluid, specifications .................269
lubricant specifications ..........269
shift interlock ..........................189
Bulbs ............................................46
C
Capacities for refilling fluids ....269
Car2U garage door opener .........68
Cell phone use ..............................8
Changing a tire .........................206
Child safety seats ......................133
attaching with tether
straps .......................................141
in front seat ............................134
in rear seat ......................134, 137
LATCH .....................................138
recommendations ...................131
Child safety seats - booster
seats ...........................................144
Cleaning your vehicle
engine compartment ..............231
instrument panel ....................232
interior .....................................233
Index
280
2010 Town Car(tow)
Owners Guide, 1st Printing
USA(fus)
Page 281 of 285

plastic parts ............................231
washing ....................................229
waxing .....................................230
wheels ......................................230
wiper blades ............................232
Climate control (see Air
conditioning or Heating) ............38
Clock ............................................55
Compass, electronic
set zone adjustment .................22
Console
rear ............................................56
Controls
power seat .................................98
steering column ........................63
Coolant
checking and adding ..............245
refill capacities ................249, 269
specifications ..........................269
Cruise control
(see Speed control) ....................60
Customer Assistance ................197
Ford Extended
Service Plan ............................277
Getting assistance outside the
U.S. and Canada .....................226
Getting roadside assistance ...197
Getting the service
you need .................................222
Ordering additional owner’s
literature .................................227
Utilizing the
Mediation/Arbitration
Program ...................................226D
Daytime running lamps
(see Lamps) ................................43
Defrost
rear window ..............................41
Dipstick
automatic transmission
fluid ..........................................264
engine oil .................................240
Driving under special
conditions ..................................192
through water .........................196
E
Electronic message center .........18
Emergencies, roadside
jump-starting ..........................215
Emergency Flashers .................198
Emission control system ..........260
Engine ........................................272
cleaning ...................................231
coolant .....................................245
fail-safe cooling .......................249
idle speed control ...................243
lubrication specifications .......269
refill capacities ........................269
service points ..................238–239
starting after a collision .........199
Engine block heater .................182
Engine oil ..................................240
change oil soon warning,
message center .......................240
checking and adding ..............240
dipstick ....................................240
Index
281
2010 Town Car(tow)
Owners Guide, 1st Printing
USA(fus)
Page 283 of 285

J
Jack ............................................206
positioning ...............................206
storage .....................................206
Jump-starting your vehicle ......215
K
Keyless entry system
keypad .......................................87
locking and unlocking doors ....88
programming entry code .........87
Keys .......................................77, 92
positions of the ignition .........179
L
Lamps
autolamp system .......................42
bulb replacement
specifications chart ..................47
daytime running light ...............43
headlamps .................................42
headlamps, flash to pass ..........43
instrument panel, dimming .....44
interior lamps .....................46, 48
replacing bulbs .........................49
LATCH anchors .........................138
Lights, warning and indicator ....12
anti-lock brakes (ABS) ..........185
Load limits .................................168
Locks
childproof ..................................79
doors ..........................................77
Lubricant specifications ...........269
Lug nuts ....................................214
Lumbar support, seats ...............98M
Message center .....................18–19
english/metric button .........22–23
system check button ................22
warning messages .....................23
Mirrors .........................................58
automatic dimming rearview
mirror ........................................58
fold away ...................................60
heated ........................................59
programmable memory ............84
side view mirrors (power) .......58
Motorcraft parts ........235, 251, 268
O
Octane rating ............................256
Oil (see Engine oil) ..................240
P
Parking brake ............................185
Parts (see Motorcraft parts) ....268
Passenger Occupant
Classification Sensor .................104
Pedals (see Power adjustable
foot pedals) .................................60
Power adjustable foot pedals .....60
Power distribution box
(see Fuses) ...............................203
Power door locks ........................77
Power mirrors .............................58
Power point .................................55
Power steering ..........................187
fluid, checking and adding ....263
fluid, refill capacity ................269
Index
283
2010 Town Car(tow)
Owners Guide, 1st Printing
USA(fus)