sat LOTUS ELISE 2005 Owners Manual

• Follow the Maintenance Schedule and keep the car in good
condition.
• Never leave young children unattended in the car.
• Read and take account of all
WARNINGS in this hand-
book.
Owners should note that the only approved extras and modi
-
fications are those which are specified by Lotus and carried out by Lotus or by an authorised dealer. Lotus does not accept
any liability whatsoever for defects which arise from extras or modifications which are not Lotus approved.
WARNING: Inexpert or unapproved modifications or additions to
the car could adversely affect the handling of the car and
the operation of its safety equipment. Ensure only modifi
-
cations specified by Lotus are undertaken by authorised
dealers. Failure to comply with this may result in a crash in
which you and others may be killed or seriously injured.
REPORTING SAFETY DEFECTS If you believe that your car has a fault which could cause a
crash, injury or death, you should immediately inform the Na
-
tional Highway Traffic Safety Administration (NHTSA) in addition
to notifying Lotus Cars USA, Inc. 2236 Northmont Parkway,
Duluth, Georgia 30096. Tel: 770 476 6540. If NHTSA receives similar complaints, it may open an inves
-
tigation, and if it finds that a safety problem exists in a group of cars, it may order a recall and remedy campaign. However,
NHTSA cannot become involved in individual problems between
you and your dealer, or Lotus Cars USA, Inc. To contact NHTSA, you may either call the Auto Safety Hotline
toll-free at 1 (888) -327- 4236 (or 366- 0123 in Washington, D.C.
area) or write to: NHTSA, U.S. Department of Transportation,
Washington, D.C. 20590. You can also obtain other information about motor car safety from the Hotline.
Pre- delivery Inspection Lotus strives at all times to provide the highest level of cus
-
tomer satisfaction, and to this end, quality assessments are made at several stages of the delivery process from factory to
customer. If necessary, repairs and replacements will be made
Safety Information
10

oh_croft_InD.indd 1020/05/2004 07:58:41ProCarManuals.com

• Drivers airbag circuit;
• Passenger airbag circuit;
• Seatbelts pre-tensioner circuit;
• Internal componentry of the sensor and diagnostic module.
As a bulb and circuit check, the tell tale will light briefly when
the ignition is switched on, and then go out. If the lamp lights at any other time, a fault in the airbag system is indicated, which
should be rectified without delay by your Lotus dealer.
WARNING: If the airbag tell tale does not light up as the ignition is
turned on, or remains lit for more than a few seconds, have
the fault rectified immediately by your dealer. Ignoring the
tell tale can result in serious injury or death if the airbags do not inflate when needed.
Airbag Deployment If a crash or collision causes the airbags to inflate, you may
see what looks like smoke, but is actually powder from the airbag
surface used to aid smooth deployment. Although the powder is not harmful, people with respiratory problems may experience
some temporary discomfort. If this occurs, get out of the car if possible as soon as it is safe to do so. After airbag deployment, the airbags, seat belt tensioners
and electronic control unit must be replaced by a Lotus dealer
or other suitably qualified organisation. Component parts of the airbag system are located in various
sites around the car. Any technician working on the car should be advised that the car is fitted with airbags to allow suitable
precautions to be taken.
WARNING:
• For up to 20 seconds after the ignition has been turned off and the battery disconnected, an airbag can still

inflate if improper servicing occurs. You can be injured
if you are close to an airbag when it inflates.
• Airbag system components should be serviced only by an authorised Lotus dealer. Do not work on the airbag
system yourself.
• The disposal of used airbag units is subject to stringent
Seating & Safety Restraints
24

oh_croft_InD.indd 2420/05/2004 07:58:45ProCarManuals.com

Child Restraints
WARNING:
Lotus strongly recommends that children are not car
-
ried in the Elise due to the risk of death or serious injury if the child is too close to the dashboard when the airbag
inflates.

Accident statistics show that children are safer when properly
restrained in the back seats of cars, an option unavailable on
this model. In addition, your car is equipped with a passenger’s airbag which poses serious risks to children - particularly infants
and small children. If, nevertheless, a child is to be carried in the
car, the following notes are provided for guidance:
When a child is of a physical size whereby the standard
fitment lap and diagonal seat belt will fit satisfactorily, with the belt positioned over the collar bone and against the centre of
the chest, the standard seat and seat belt should be used. If the
belt touches or crosses the child’s neck, the child should NOT
be carried in the Elise.
WARNING:
• Children should not be carried in the Elise unless they are large enough to be able properly to use the standard
seat belt without any child seat or booster seat.
• Child restraint systems (other than belt positioning booster seats) are designed to be secured in the car seat
by the lap belt portion of the lap/shoulder belt. READ
ALL INSTRUCTIONS THAT ACCOMPANY THE CHILD RESTRAINT OR BOOSTER SEAT.
• I n f a n t s w h o a r e u n a b l e t o s i t u p b y t h e m s e l v e s ,

unsupported, should NOT be carried in the Elise.
• Never put a rear-facing child seat in the passenger seat
of the Elise. If the airbag inflates, it can hit the child or
the back of the child seat with enough force to kill or very seriously injure an infant.
• There is no provision on the Elise to switch off or disable
the passenger airbag.
WARNING: Children who are not properly restrained can be killed
or seriously injured in an accident.
Seating & Safety Restraints
26

oh_croft_InD.indd 2620/05/2004 07:58:45ProCarManuals.com

Car Security AlarmThe Lotus Elise is fitted with a Cobra 8186 immobiliser/alarm
which includes the following features:
• ‘Dynamic coding’ of the transmitter fobs; Each time the trans
-
mitters are used, the operating frequency is random changed
to guard against unauthorised code copying.
• Automatic (passive) engine immobilisation to prevent the engine from being started without the transmitter fob.
• Sensing switches on doors, front body access panels and the engine cover, meaning the alarm sounds if someone tries to
force entry.
• Personal protection by ‘on demand’ activation of the siren.
• Selectable cockpit intrusion sensing using a microwave

sensor.
• Self powered siren to maintain protection if the car battery is
disconnected.
Transmitter Fobs Two transmitter fobs are provided with the car to operate the
immobiliser/alarm system. The two transmitters should be kept
separate, and a replacement obtained immediately after any loss to ensure that a spare is always available.
Each individual alarm system has a unique serial number
and an owner’s Personal Identification Number (PIN), both of
which are printed on a code card supplied with the car. In order to allow replacement transmitters to be ordered, it is essential
that these numbers are recorded and kept safely with the car
documents. If the code card is not available on receipt of the
oh102
Small button
Keys & Car Security Alarm
30
COBRA TRANSMITTER FOB & CODE NUMBERS
Push button
Fob tell tale
S / N 99999999
PIN CODE = 9999

oh_croft_InD.indd 3020/05/2004 07:58:46ProCarManuals.com

car, enquire with the dealer immediately.
Engine Immobiliser In order to provide a measure of car security, independent
of any driver action, the system will ‘passively’ immobilise the
engine’s cranking and running circuits after the first occurring of the following:
i) Four minutes after switching off the ignition;
ii) Two minutes after a mobilising command (see below); or
iii) One minute after switching off the ignition and opening the driver’s door.
The immobilised state is indicated by the security tell tale in
the tachometer upper face flashing continuously. To mobilise the engine, press once, and for a full second, the
larger of the two buttons on the transmitter fob. The security tell
tale will be extinguished.
Valet Mode

If leaving the car for servicing or parking, the passive immobil
-
isation feature may be switched off by switching on the ignition
and pressing the transmitter small button. Two beeps will confirm
‘valet’ activation, repeated as a reminder when the ignition is switched off. The security tell tale will remain off. At the next arming command, the valet mode will be switched
off, and normal immobilisation resume.
ohs127a
Keys & Car Security Alarm
31
TachometerSecurity/ RPM tell tale

oh_croft_InD.indd 3120/05/2004 07:58:47ProCarManuals.com

Arming the AlarmRemove the ignition key, close (and lock) both doors, and
check that the engine cover and front body access panels are
secure. The roof may be either closed or open. Press once, and for a full second, the larger of the two buttons on the trans
-
mitter fob (on cars with central door locking, this action will automatically lock both doors - see later). This command will
be acknowledged by:
- 2 flashes of the hazard warning lamps;
- Continuous flashing of the security tell tale.
Check that these indications occur. If not, press the button a
second time, as the first press may have only switched off the passive immobilisation (see above). Note that if the system is armed when a door or engine cover/
front access panel is not fully closed or if the interior lamp is in the ‘off’ position, a continuous buzz will be heard as warning. If still open after expiry of the arming period, (see below)
the alarm will be armed with that switch group (both doors, or
front/rear access lids) excluded from the circuit.
After arming the system, the engine is immediately immo
-
bilised, but a period of approximately 45 seconds must elapse
before all functions and sensors become fully active. After
this time, the alarm will be triggered by any of the following actions:
- Interruption of the car battery power supply.
- Energising the ignition circuit (‘hot wiring’).
- Opening a door;
- Opening the engine cover or a front access panel.
- Movement detected within the cabin.
When the alarm is triggered, the hazard warning lamps will
flash and the electronic wailing siren will sound for a period of approximately 30 seconds before closing down and resetting, ready for any further triggering input. If a trigger is continuously
present, the alarm will repeat after a short delay, and continue
in this sequence for about 10 cycles. To silence the siren when triggered, press once, and for a full
second, the larger button on the transmitter fob. This will not affect the status of the alarm which will remain armed.
Keys & Car Security Alarm
32

oh_croft_InD.indd 3220/05/2004 07:58:47ProCarManuals.com

Transmitter Fob Battery ReplacementThe transmitter fobs will normally operate within a range of 5
metres from the car, but this may be reduced by the presence
of other radio signals in the vicinity. A small LED tell tale on the
transmitter fob will flash whilst the button is held down to indicate correct operation, but if the lamp flashes irregularly or only once,
transmitter battery replacement is required.
The transmitters are powered by a long life 3V Lithium battery,
type CR2032, which with normal use should last for 3 years. To ensure continuity of operation, it is recommended to renew the batteries every 12 months:
- Using a small screwdriver, prise open the case in the areas
marked ‘open’.
- Remove the old battery and wait for 10 seconds before insert
-
ing the new battery with +ve sign uppermost, and holding the battery only by the periphery.
- Align the locating studs, and firmly press the case together.
- The transmitter should now operate normally, but may require
re-synchronisation with the control unit.
Transmitter Re-synchronisation If at any time the transmitter does not function, and the battery
is known to be good, carry out the following re-synchronisation procedure:
- Stand close to the car and hold down both buttons on the
transmitter until the LED on the fob is extinguished (approx.
10 seconds).
ohs102
Keys & Car Security Alarm
35
Transmitter casing
Transmitter body
Batter y

oh_croft_InD.indd 3520/05/2004 07:58:48ProCarManuals.com

- Release both buttons; the fob tell tale should come on con-
stantly.
- Press the larger button for one second (the fob tell tale will
flash). Synchronisation is complete.
Programming Additional Transmitter Fobs Two transmitter fobs are provided with the new car. If one
transmitter is lost or damaged, a replacement should be ob
-
tained immediately from your dealer, and programmed to the car alarm controller using a functioning transmitter fob and the
system owner’s unique Personal Identification Number (PIN).
Up to 4 transmitter fobs can be matched with the alarm system, but all fobs must collectively undergo the single programming
operation:
1. Press, simultaneously, both buttons on a transmitter fob until the fob tell tale stops flashing (approx. 10 seconds).

On release of the buttons, the fob tell tale will light.
2. Repeat operation (1) for ALL the transmitter fobs required to
operate the system.
3. Turn the ignition on and off 3 times within 7 seconds; the
security tell tale in the tachometer will light for 3 seconds.
4. Enter the PIN: Immediately the tell tale goes out, switch ON the ignition and count the number of security tell tale flashes
until equal to the first number of the PIN, then turn the ignition
OFF, then back ON again.
5. Repeat operation (4) for the remaining 3 digits of the PIN, remembering to turn the ignition OFF and back ON after each
code number.
Note: If at any time a mistake is made when entering the
PIN, turn the ignition OFF for 10 seconds and re-commence entering the PIN.
6. If the PIN is correct, the security tell tale will be lit. Test op
-
eration of each transmitter fob.
Disconnecting the Car Battery If the battery is to be disconnected, refer to the ‘Battery’
section later in this handbook which includes the following precaution:
- Before disconnecting the battery, ensure that the alarm system
is disarmed and mobilised.
Keys & Car Security Alarm
36

oh_croft_InD.indd 3620/05/2004 07:58:48ProCarManuals.com

Passive Ilisation: The start button will operate only when the
security tell tale in the tachometer face is out. If the tell tale is
flashing, the engine is immobilised; Press once,
and for a full second, the larger of the two buttons on the trans
-
mitter fob. The security tell tale will be extinguished. For further
information see ‘Car Security Alarm’.
WARNING ‘TELL TALE’ LAMPS A block of tell tale lamps is incorporated into the instrument
cluster to provide you with important information concerning the
operation of your Elise.
Bulb Check In order to check that the warning systems are operative, all
the tell tale lamps (except the ‘security’ tell tale; see Car Se
-
curity Alarm section) should light for about 6 seconds following ignition switch on. If any lamp should fail to light, it is possible
that the bulb or warning circuit may be faulty; see your dealer
without delay.
Turn Tell Tale
When the left hand or right hand turn indicators are operating,
this green tell tale flashes in unison. A clicking sound may also be heard. If the tell tale fails to light, or flashes at an unusual or
irregular rate, check the operation of the turn indicator lamps
immediately.
m252a
Instruments & Switches
46
TELL TALE LAMPS

oh_croft_InD.indd 4620/05/2004 07:58:51ProCarManuals.com

stopping distance, a locked wheel provides little or no steering
force, such that with both front wheels locked, movement of the steering wheel has no effect on car direction. With the anti-lock
system, even panic braking results in controlled deceleration and the retention of steering response. ABS is especially ad
-
vantageous when braking on slippery road surfaces and in bad driving conditions, but it is important to realise that the ABS
cannot increase the friction level at the road surface, but can only make optimum use of the grip available.
WARNING: When driving in adverse weather, or on poor road sur
-
faces, always be alert to the possibility of slippery condi
-
tions and make the necessary allowance for increased stop
-
ping distances. Failure to do so may result in an accident in which you or others may be killed or seriously injured.
Normal braking, controlled by the pressure applied to the
brake pedal, occurs when the road conditions allow for decel
-
eration to be achieved without danger of wheel lock. The relative
speeds of the four wheels are continuously monitored by the
ABS when the brakes are applied, and if one or more wheels begin to lock, the brake pressure to that wheel(s) is modulated
by the ABS to help keep the wheel rotating and provide the
maximum controlled braking force. The wheels may appear
to lock momentarily as the wheel speed rapidly changes, and some tire noise (intermittent screeching) may be heard which is normal and will vary with road and tire conditions. Note that the
ABS does not function at speeds below 5 mph (7 km/h). When the ABS is activated, the driver is will feel a ‘pulsing’
sensation at the brake pedal as the fluid pressure is modulated, and also by audible clicking sounds. These signals indicate to
the driver that maximum braking is occuring, and that driving style should be modified to suit the conditions.
The minimum stopping distance is achieved by applying the
brakes firmly and steadily, and allowing the ABS to modulate
hydraulic pressure. The driver should not attempt to emulate
this process by ‘pumping’ the brake pedal, as modulation at the pedal will treat all four wheels similarly, rather than the individual
wheel control allowed by the electronics. An ABS tell tale lamp in the instrument panel is provided
to warn of any problems in the system and to indicate that the
Driving Controls
68

oh_croft_InD.indd 6820/05/2004 07:58:57ProCarManuals.com