wiring MAZDA 323 1992 Suplement User Guide

TROUBLESHOOTING GUiDE F3
15 ENGINE STALLS ON DECELERATION
IESCRIP-
l Engrne unexpectedly stops running dunng or after deceleration
[iON l Idle condition normal.
TROUBLESHOOT1NG HtNTS]
ingrne speed drops too much when releasrng accelerator
3 Idle-speed misadjustment @I Loose connector disconnected by force of deceleration
3 Fuel-cut contrd malfunction
TEP lNSPECTlON ACTION
1 1s idle condition normal? Yes Go to next step
tdle speed: 800 f 50 rpm (in neutral)
NO Adjust or perform Troubleshooting, Nos.
8-I 1 “ROUGH IDLE”
(Refer to Workshop Manual
(1203-I o-89F))
2 Is “00” displayed on Self-Diagnosis Checker Yes Go to next step
with ignition switch ON?
SYSTEM SELECT: 1 NO Service Code No. displayed
Check for cause (Refer to specified
check sequence) ET page F3-16
“88” flashes
Check ECU termrnal 1 F voltage
Voltage: Battery voltage
(ignition switch ON) r;r page F346
W:SELFTEST
e If OK, replace ECU CI page F3-3
4 If not OK, check wirtng
(ECU - Self-Diagnosis Checker)
3 Does Self-Diagnosis Checker Monitor Lamp with Yes Go to next step
lgnttlon switch UN show that switches operate
correctly?
NO Lamp not ON or OFF with specified
switch
Check for cause (Refer to specified
check sequence)
W: SEtF TEST Lamp slways ON
Check wiring between
(ECU terminal 1 D - Self-Diagnosis
Checker)
4 Are ECU ?erminal voltages OK? Yes Go to next step
(especially IV, 20, 20, ZU, 2V.
and 20) v page F346 No
Check for cause
5 Check for poor connection of foltowing parts YC?S Repair or replace
l ignrtion coil l Igniter l Olstribdor l High-tension lead
NO Go to next step l Injector. l Injector resistor l Ctrcuit-opening relay . l ECU
F3-35

F3 TROUBLESHOOTING GUIDE
STEP INSPECTION ACTlON
6 Is dashpot correctly adjusted? Yes Go to next step
c
Dashpot set speed: Approx. 3,500 rpm
No Adjust dashpot
7
Try known good ECU; does condition
Improve?
w page F3-3
13EOF3-336
16 ENGINE STALLS SUDDENLY (INTERMITTENT)
DESCRIP.
l Engine intermittently stops running
TION l Before stalling, engine conditron is OK
TROUBLESHOOTING HINTS]
@ intermittently no spark or no fuel injection caused by ve-
hlcle vibratron, acceleratton, or deceleration
l Poor connectlon in wiring harness
iTEP INSPECTION ACTfON
1 Is “00” displayed on Self-Oiagnoss Checker Yes Go to next step
with lgnltlon swrtch ON?
NO Service Code No. displayed
Check for cause (Refer to speclfled
check sequence).
Note CT page F3-16
l When checking wiring harness and
connectors, tap, move, and wiggle
suspect sensor and/or harness to
recreate problem
“88” flashes ’
Check ECU terminal IF voltage
Voltage: Battery voltage
{ignition swttch ON) w page F3-45
4 If OK, replace ECU
4 If not OK, check wiring
(ECU - Self-Diagnosis Checker)
2 Check for poor connection of foliowrng parts
Yes Reparr or replace
l lgnltfon coil l Igniter l Distributor l t-flgh-tensron lead
No Go to next step l Injector l Injector reststor l Circutt-opening relay l ECU
3 Are ECU terminal voltages OK? Yes Go to Troubleshbotrng No. 2
(especially 16, 2A, 2B, and 2C) .“CRANKS NORMALLY BUT WILL NOT
w page F3-45 START (NO COMBUSTION)”
w page F3-20
Note
. No Check for cause
l When. checking voltages, tap, move, and
wiggle harness and connector to recreate
problem
* lrlrl m-7
F3-36
7.8-l

F3 FUEL SYSTEM
t 3EoF3-344
1
FUEL SYSTEM
FUEL PUMP
inspection
Fuel pump operation
1. Connect the diagnosis connector F/P and GND terminals
by using a jumper wire.
2. Remove the fuel filler cap.
3. Turn ON the ignition switch.
4.
Listen at the filler inlet for the operational sou.nd of the fuel
pump.
5. Install the fuel filler cap.
6. If no sound is heard, measure the voltage between the fuel
pump connector (G/R) to a ground.
Voltage: 8attey vo kage
7. If not as specified, check the circuit opening relay and circuit.
8. ff as specified, check fur continuity between fuel pump con-
nector (G/R) and (B).
9. If there is continuity, reptace the fuel pump.
10. If there is no continuity, repair the ground circuit.
f3EOF3.345
13EOF3-346 FUEL PUMP RESlSTORlRELAY
System Operation
1. Remove the rear seat cushion.
2. Measure the voltage at the fuel pump connector terminal
A (G/R).
Voltage
I
Cranking
1 Battery voltage
Ignition switch ON ov 3. If not as specified, perform the following inspections, and
repair or replace as necessary.
l Fuel pump resistor/relay resistance
(Refer to page F3-41.)
l ECU 11 terminal voltage (Refer to page F3-45.)
l Wiring harness and connector
F3-40
ii e -
*
_~ --
C --
A-'

-,
-,
--
--
-1
E
7
2
I
i 3EAR SE
--

CONTROL SYSTEM F3
hT==TdI ,
USE CONNECTOR A 1
L
93GOF3-787 ENGINE CONTROL UNIT (ECU)
Inspection
1. Disconnect the ECU connectors.
2. Connect the SSTs {Engine Signat Monitor and Adapter) to
the ECU as shown.
3. Place the SST (Sheet) on the Engine Signal Monitor.
4. Measure the voltage at each terminal.
(Refer to pages F3-46 to F3-53.)
5. If any ECU terminal voltage is incorrect, check the related
input or output devices and wiring. If no problem is found,
replace the ECU. (Refer to page F3-2.)
t
1 13EOF3-358
r
TERMINALS
f. -I AANDB . Caution l Never apply voltage t.o terminals A and 8 of the SST.
! :OF3-359
F3-45

,,1
CONTROL SYSTEM F3 ‘1
Va: Battew voltage
Incorrect voltage Possible cause
Always OV
l ROOM IOA fuse burned l Open circuit In wiring from ROOM 10A fuse to ECU termina! 1A
Always OV
l Main relay malfunction l Open or short circuit in wiring from main relay to ECU terminal IB
Always OV (starter turns)
l Open or short circuit in wiring from ignition switch to ECU terminal IC
Always OV
Always VB
l Maln relay (FUEL INJ relay) malfunction l Open circuit in wiring from main relay to diagnosis connector terminal +B l Open or short circuit in wiring from diagnosis connector terminal MEN to
ECU terminal 1 D
l Poor connection at ECU connector l ECU malfunction
Always approx. 5V . ECU malfunction
Always below
2.5v
Always Ve -
-
No display on Self- * Main relay (FUEL INJ relay) malfunction
Diagnosis Checker
l Open circuit in wiring from main relay to diagnosis connector terminal + B
“88” displayed and
l Open or short clrcurt in wiring from diagnosis connector terminal FEN to
buzzer sounds con- ECU terminal tF
ti nuousl y
l Poor connection at ECU connector l ECU malfunction
Always QV
l Short circuit in wiring from igniter to ECU terminal 16
Always OV or VB
l Refer to Code No.42 Troubleshooting
(Refer to 323 4-Wheel Drtve Workshop Manual (12?9-IO-89L))
Always VB
Always OV
Always below
2.5V
Atways Ve I ’
l Fuel pump resistor/relay malfunction
l Open or short circurt in wiring from ECU terminal II to fuel pump resis-
tor/relay
A/C does not operate
l A/C reiay malfunction l Open circuit in wiring from ignition switch to A/C relay l Open circuit in wiring from A/C relay to ECU terminal 1J
A/C switch
OFF but l Short circuit in wiring from AIC relay to ECU terminal 1 J
A/C operates . ECU malfunction
l Poor connection at ECU connector l ECU malfunction
Always below 1 .OV a Short circuit in wiring from diagnosis connector terminal TEN to ECU termi-
nal 1K
Always Vs
l Open circuit In wiring from diagnosis connector terminal TEN to ECU terml-
nal IK
-
-
l Open circuit in winrig from diagnosis connector terminal GND to ground’
-
I -
.
. .
-. F3-47

-. _.. . . . . . _ - ._.
-w
CONTROL SYSTEM F3
I .
-.
Ve: Battery voltaae I
Incorrect voltage
Atwafi below 1 .OV
Always VB
Always VS (foglight switch OK)
Always below 1 .OV
Always below 1 .OV
Always Vs
Always
below 23 (blower fan OK)
Always VB (blower fan OK)
Always below 1 .OV
(electric cooling fan OK) -
1-
Possible cause
l Throttle sensor mrsadjustment l Short circuit in wtrrng from throttle sensor to ECU terminal 1 N l ECU malfunction
l Throttle sensor mrsadjustment l Open circuit in wiring from throttle sensor to ECU terminal fN l Open circuit in mnng from throttle sensor to ECU terminal 20
l Foglight relay malfunctron
l Foglrght relay malfunction
l P/S pressure switch maltunctron l Short crrcurt In wrrlng from P/S pressure switch to ECU terminal 1 P l ECU malfunction
l P/S pressure switch malfunction l Open circuit in wlnng from P/S pressure switch to ECU terminal 7 P l Open circuit in wiring from P/S pressure switch to ground
l A/C switch malfunctron l Short circuit tn wiring from A/C switch to ECU terminal 1Q l Poor connection at ECU connector l ECU malfunction
l #C swatch malfunction l Open circuit in wiring from A/C switch to ECU terminal 1Q l Open circuit in wiring from A/C switch to blower control switch
l Open or short circuit in wiring from fan relay to ECU terminal 1R l ECU matfunction
Always below 1 .OV (blower fan OK}
Always Vs (btower fan OK)
Always betow illumination lamp
1 .ov ON when rear
window defroster
switch ON
Illumination lamp
never ON
Atways below 1 .OV (headttghts OK)
l Short circuit in wrrtng from blower control switch to ECU terminal IS l Poor connection at ECU connector l ECU m&function
l Open crrcuit in wrrrng from blower control switch to ECU terminal 1s
l Open or short crrcuit In wiring from rear window defroster switch to ECU
terminal t T
l Open circuit in wiring from ignitron switch to rear window defroster switch l Rear window defroster switch malfunction
l Open or short circuit in wiring from headlight relay to ECU terminal 1 U
Always below 1 .OV
l Neutral switch malfunction l Clutch switch malfunction l Short circuit in wiring from ECU terminal IV to neutral or clutch switch
Always VB
l Neutral switch malfunction l Clutch switch malfunction l Open circuit in wiring from ECU terminal 1V to neutral or clutch swdch l Poor connection at ECU connector
13FOl=3-36 .
F3-49
.:i

CONTROL SYSTEM F3
VS: Battery voltage
Incorrect voltage Possible cause
Ab&e OV
l Poor contact at ground terminal l Open circuit in wiring from ECU to ground
Always approx. OV or approx. 2V
l Refer to Code No. 02 Troubleshooting
(Refer to 323 Workshop Manual (l203-lo-89F))
Always approx. OV or approx. 1.5V
l Refer to Code No, 03 Troubleshooting
(Refer to 323 Workshop Manual (1203-lo-89F))
Always OV
Always OV
- -
l Refer to Code No. 05 Troubleshooting
(Refer to 323 4-Wheel drive Workshop Manual (1229-10-891))
l Short circuit in wiring from ECU terminal 2K to throttle sensor, or airflow
meter
l Poor connection at ECU connector l ECU matfunctlon
Below 4.5V or above 5.5V
-
l ECU matfunction
l Refer to section 1
Always OV
l Throttle sensor malfunction l Short circuit in wlnng from ECU termrnal 2M to throttle sensot l Poor connection at ECU connector
. ECU malfunction
Always approx. 5V . Throttle sensor misadjustment
l Open circuit in wiring from ECU terminal 2D to throttle sensor
Always constant
l Open circuit in wiring from ECU terminal 2M to throttle sensor
. Open circurt in wiring from ECU terminal 2K to throttle sensor
l Open circuit in wiring from ECU terminal 2D to throttle sensor
Always above 1V 1 . Throttle sensor mtsadjustment
Always OV (after warm-up)
Always approx. IV (after warm-up)
l Refer to Code No. 15 Troubleshooting
(Refer to 323 Workshop Manual (1203-I O-89F))
l Refer to Code No.17 Troubleshooting
(Refer to 323 Workshop Manual (1203-lo-89F))
Always OV or approx. 5V
l Refer to Code No. 08 Troubleshooting
(Refer to 323 Workshop Manual (t203-lo-89F))
Always OV or approx. 5V
Always OV or approx. 5V
l Refer to Code No. 10 Troubleshooting
(Refer to 323 Workshop Manual (l203-lo-89F))
l Refer to Code No. 09 Troubleshooting
(Refer to 323 Workshop Manual (1203-10.89F))
Always OV
I
l Indicator broken l Open or short circuit In wiring from ECU 2R to ignition switch
13EOF3-36;
F3

VB: Battery voltage
Incorrect voltage Possible cause
Always OV
l Open or short &curt in wirtng from ECU terminal 25 to buzzer
Always OV or VB
l Refer to Code No.25 Troubleshooting (Refer to page F3-18)
-
Always OV l Main relay (FUEL INJ relay) malfunction l Open or short crrcult rn wlnng from Injector to ECU termtnal 2U or 2V
Always Va
l ECU matfunctlon
Always OV or VB
Always OV or VB
Always OV
Atways OV or VB
l Refer to Code No.34 Troubleshooting
(Refer to 323 Workshop Manual (1203-t O-89F))
l Refer to Code No.26 Troubleshooting
(Refer to 323 Workshop Manual (1203-lO-89F))
l Open or short circuit in wiring from ECU terminal 2Y to relay
l Refer to Code No. 35 Troubleshooting (Refer to page F3-18)
F3-53

Mazda
323
4WD
Wiring Diagram
Europe (LHD)
FOREWORD
This wiring diagram incorporates the wiring schematics
of the basic vehicle and available optional equipment.
Actual vehicle wiring may vary slightly depending on
optional equipment or local specifications, or both.
All information in this booklet is based on information
available at the time of printing. Mazda Motor Corpora-
tion reserves the right to make changes without pre-
vious notice.
CONTENTS
Mazda Motor Corporation
HIROSHIMA, JAPAN APPLICATION:
This manual is applicable to vehicles beginning with
the Vehicle Identification Numbers(VlN) shown on
the following page.
8 1992 Mazda Motor Corporation
PRINTED IN JAPAN, JAN. ‘92 R
5232-lo-92A

VEHICLE IDENTIFICATION NUMBERS (VIN)
(CHASSIS NUMBER)
JMZ 86835200 5OOOOl-
WIRING COLOR CODE
Color Code
I Color Code
Blue I L 1 Natural
I N
Black
1 B I Orange
I 0
Brown BR
Dark Blue DL
Dark Green DG Pink
Red
Purple
Green
Gray
Light Blue
Light Green G
GY
LB Tan
White
Yellow
Violet P
R
PU
T
W
Y
LG
I V