load capacity MAZDA 323 1992 Workshop Manual Suplement

..,. .
a
._
GI CAUTKN
PRECAUTIONS TO TAKE WHEN SERVICING AN ELECTRICAL SYSTEM l Note the following items when servicing the electrical system.
l Do not alter the wiring or electrical equipment in any way; this may damage the vehicle or cause a fire
from short-circuiting a circuit or overloading it.
l The negatrve (-) battery cable must be removed first and
rnstalled last. l Do not reptace with fuses exceedrng specified capacity
Cautron
l 8e sure that the ignitton and other switches are off
before disconnectrng or connecting the battery cables.
Failure to do so may damage the semrconductor
components. Caution l Repfacing a fuse with one of a larger capacrty than
desrgnated may damage components or cause a frre.
l Secure harnesses with provrded clamps to take up slack. l Tape areas of the harness
that may rub or bump l When mounting
components, be sure the
against sharp edges to
protect rt from damage. harness IS not caught or
damaged.
Caution
l Clamp all harnesses near vibratrng components (for
example, the engine) to remove slack and to prevent
contact resultrng from vibration. i Drsconnect heatsensitive l Make sure that the
parts (for example, relays
and ECU) when performing connectors are securely
connected when installed.
l Do not handle electrical components roughly or drop
them. maintenance (such as
weldrng) where
temperatures may exceed
80°C [176OFj.
-*
HI

TD TECHNICAL DATA
CLUTCH
Jmn -
Clutch control
Clutch oedat Engine/Transaxle BP DOW turbo
G25MX-R {G5MX-R)
Hydraulic Type I
Suspended
Pedal ratio mm [in) 6.55
Full stroke mm {in] 135 t5.311
Height (With carpet) mm [in] 196-204 (7.72-8.03 1
Free play mm (in] 5.5-l 7.4 {0.22-0.69 ]
Distance to carpet when clutch fully
disengaged mm [in) Minimum 41.0 (1.61 ]
Flywheel
Runout limit mm {in] 0.200 [ 0.0079)
Clutch disc
1
, Type I Single dry plate
Runout limit mm (in) 0.700 [ 0.0276 )
Wear limit mm {in] 0.3 [ 0.012 ] from rivet head
Outer diameter mm {in] 230 {9.05)
Inner diameter mm {in) 155 i6.10)
Facing thickness mm [in] Flywheel side
I 3.5 (0.14)
Pressure elate side 3.5 10.141
Clutch cover
Type
Set load
Ctutch fluid
Type I
N [kgf, Ibf) 1
I Diaphragm spring
5,494 1560, 1,232)
SAE J1793 or FMVSS116 DOT-3 MANUAL TRANSAXLE AND TRANSFER
SpecMcation
Transaxle type
Transaxle control
Transaxle shift control
Syncromesh system G25MX-R (G5MX-R)
Floor shift
Cable
Forward: Synchromesh
Reverse: Seiective sfidina and svnchromesh
I 1 st 3.454 a
2nd 1.833
3rd 1.310
Gear ratio
4th 0.970
5th 0.717
Reverse 3.166
Final gear ratio I . 4.214
Speedometer gear ratio (Driven gear/drive gear) 1.045 (23122)
Grade API service GL-4
011 Viscocity AkeaSQn: ATF Dexron@II or M-ID
Above -l8*C (OOF): SAE 75W-90
Capacity L {USqt, Imp itI 2.6 12.7, 2;2]
Runout
Primary shaft gear runout
Secondary shaft gear runout mm {in) 0.050. [ 0.0020 ]
mm [in] 0.015 { 0.0006 ]
Clearance
1st’ (Gear inner dia. -shaft puter dia)
2nd (Gear inner dia. -shaft outer dia)
3rd {Gear inner dia. -shaft outer dia)
4th (Gear inner dia. -shaft outer dia)
5th (Gear rnner dia. -shaft outer diaj mm {in] 1 0.030-0.080 { 0.0012-0.0~3 11
mm {in) 0.030~0.08C (-0.0012-0.0031 1
mm (in) 0.030-0.080 I 0:0012-0.003i 1
mm [in] 0.030-0.080 [ 0.0012-0.0031 ]
mm [lnl 0.030--0.080 ~0.0012-0.0031 1
1. TD-8
Lern
l-2 sift for
3-4 shift fri
5th shift f;t
Reverse iti
Thrust cli
1st gear
2nd gear
3rd gear
4th gear
5th gear
. .
Primary St
Seconda:
Center ci
Type :
Number
c
Number (
Number r
Number ;
Bearing ;
Bearing
1
End plai
Ring get
End pi&i
Sun gea
frltnsfe~
Final g&f
Number

TECHNICAL DATA TD
Item
t-2 slmfl fork and reverse gear Standard 0.1 O-O.45 [ 0.004-0.018 1
mm {in] Wear limit
I 0.95 (0.037 ]
3-4 shift fork and ctutch hub sleeve Standard 0.10-0.40 [0.004-O.OlS]
mm [In]
Wear limit
I 0.90 (0.035 ]
5th shift fork and clutch hub sleeve Standard 0.10-0.36 {0.004-0.014]
mm [in]
Wear limit
I 0.86 [ 0.034 1
Reverse idle gear and reverse lever Standard 0.10-0.35 ~0.004-0.014 )
mm fin)
Wear limit
I 0.85 tO.033)
Standard o-0.05 [ 0-0.002 ]
Primary shaft gear mm [in ] 0.20 lO.OOS], 0.25 [O.OlO), 0.30 (0.012], 0.35 (0.014),
Adjustment shims 0.40 lO.OlS], 0.45 [O.OlS), 0.50 (0.020], 0.55 [0.022],
0.60 fO.0241. 0.65 f0.0261. 0.70 fO.0281
Standard t 0.03-0.08 { 0.001-0.003 1
Secondary shaft gear mm [in] 0.20 tO.O08], 0.25 {O.OlO], 0.30 (0.012], 0.35 [0.014),
Adjustment shims 0.40 (O.Ot6], 0.45 (0.018], 0.50 [0.020], 0.55 10.022),
0.60 IO.0241, 0.65 {0.026], 0.70 [0.028]
Center differential
Me Planetary carrier
Number of ring gear teeth
Number of pinion gear teeth Outer
Inner
Outer
Inner 59
75
14
! 14
Number of sun gear teeth
Number of idle-gear teeth
Bearing preload Pinion gear side
I 43
Idle gear side 43
37
N.m { kgfcm. inlbf 1 3.0-3.9 f30-40, 27-34 )
0.25 {O.OtOl, 0.30 {0.012],
CI---.-- ---I--A --I: _d---* -L!- aeanng pretoaa aqusrmenr snrm mm [in] 0.10
0.35
0.55
0.75
0.95
1.15 0.004 ], 0.20
0.014), 0.40
0.022 ) , 0.60
0.030 ) , 0.80
0.0371, 1.00
0.0451. 1.20 0.008
0.016
0.024
0.031
0.039
0.047 -
: 0.45 lO.O18], 0.50 !0.020],
: 0.65 0.85 (0.026] [0.033], p 0.70 0.90 [ { 0.028 0.035], 1,
I 1.05 (0.041], 1.10 [P.O43], r
End play of ring gear mm {in) 0.1510.36 i 0.006-0.012 ]
Ring gear end play adjustment washer mm {in) 1.20 40.047], 1.35 t0.053], 1.50 [0.059),
1.65 {0.065], 1.80 iO.071 1
End play of sun gear mm (in]
0.100-0.300 [ 0.0039-0.0118 ]
-
Sun gear adjustment washer mm {in] 3.5 lO.lSS], 3.7 (0.146). 3.9 (0.154].
4.1 IO.161 1, 4.3 [O.lSS]
Transfer Cattier
Final gear reduction ratio 4.214
Number of teeth
Oil Ring gear -
Pinion gear
Type
Capacity
L I US qt, Imp q?] . 37
11
API: GL-5
Above -18% lOoF]: SAE 90
Below -18OC {OOF]: SAE 8OW
0.5 [0.53. 0.44)

TECHNNlCAL DATA TD
STEERlNG SYSTEM
item
Steering wheel
Outer diameter
mm (in]
Free play
mm [in]
Operation force N [kgf, Ibf]
Lock-to-lock
Steering gear
TYF
Steerrng gear ratio
Backlash between rack and pinion
mm Iin] 1
N-m { kgfcm, inlbf ]
PInion Reload measured by torque wrench
preload
kgf ( ibf )
Preload measured by pull scale with attachment
Distance between left and right brackets
mm Iin]
Rack stroke mm {ini
Lubricant type
Oil capacity L (US qt, imp qt]
Dfive belt
I
Deflection with force of 98 N { 10 kgf, 22 Ibf 1 mm [in) Specifications
370 { 14.57)
O-30 [O-l .16)
29 13.0, 6.6) or less
2.51
Rack and pinjon
Infinite too)
0 101
l.O--.I.3 (10-14, 8.?-12.1)
1.0-1.4 (2.2-3.08)
258 (10.16)
121 (4.76)
ATF Dexron@II or M-III
0.8 (0.85, 0.70)
New
belt: 8-9 [0.31-0.351
Used belt: Q---t0 [ 0.35-0.39 1
BRAKlNG SYSTEM
Brake type Item ‘WIthout A8S With ABS
. Front . . . . . djsc, Rear . . . . . dtsc
Brake pedal
Heiaht mm linl i 203-206 f 7.99-8.7 1 I
Free play mm {in]
Reserve travel
Clearance when pedal depressed at 5& N 160 kgf, G? I’dl;’ 4-7 !0.16--0.281 12-15 [0.47-0.591
70 (2.76) min 60 (2.36) min
l t Master cylinder t
Master cylinder
Front disc brake . Type
Bore diameter mm {inj 25.4 11 .UO ] Tandem
t 23.8 (0.94 ]
- .-~
Type Ventilated
Thickness of pad mm [in) Standard 10 10.39)
Minimum 2 fO.08)
Thickness of disc plate
mm [in] Standard 24 10.94)
Minimum - 22 to.791
Runout of disc plate mm fin] 0.1 ~0.004]
Cylinder bore mm (ini 57.2 (2.25 ]
Rear brake (disc) b
r Type I
Solid
Thickness of pad mm (In] Standard 8.0 (0.311
Minimum 1 10.04)
Thickness of disc plate mm [in] r Standard 10 [0.39]
Minimum 8 {0.31)
Runout of drsc ‘plate mm (iti)
0.1 (0.004]
Cylrnder bore mm {in]
34.9 II.371
Parking brake
_ Type Mechanicaj twerear-wheel control
Parking brake lever notches
When lever is pulted at 98N [‘lo kgf, 22 tbf I 5-7

Troubleshooting GI
Precautions to take when servicing an electrical system
l Note the following items when servicing the electrical system.
l Do not alter the wiring or electrical equipment in any way; this may damage the vehicle or cause a fire from
short-circuiting a circuit or overloading it. l
The negative (-) battery cable must be removed first and
installed last. l Do not replace with fuses exceeding specified capacity.
1OA
f5A
Zaution
o Be sure that the ignition and other switches are off
Caution
before disconnecting or connecting the battery
l Replacing a fuse with one of a larger capacity than
cables.
designated may damage components or cause a fire.
Failure to do so may damage the semiconductor
components.
0 Tape areas of the
l When mounting l Secure harnesses with provided clamps to take up slack.
harness that may rub or
components, be sure the
bump against sharp
harness is not caught or
edges to protect it from
damaged.
damage.
Zaution
B Clamp all harnesses near vibrating components
(for example, the engine) to remove slack and to
prevent contact resulting from vibration.
D Do not handle electrical components roughly or drop
them.
l Disconnect heat-
sensitive parts (for
example, relays and
ECU) when performing
maintenance (such as
welding) where
temperatures may exceed
80°C (176°F). l Make sure that the
connectors are securely
connected when
installed.
11