alternator belt MAZDA MIATA 1991 Factory Service Manual

ALTERNATOR & REGULATOR
1990-92 ELECTRICAL Alternators & Regulators - Mitsubishi
DESCRIPTION
Alternators are conventional 3-phase, self-rectifying type units containing 6 diodes (3 positive and 3 negative)
which are used to rectify current. See Fig. 1
. An internally-mounted, Integrated Circuit (IC) regulator is used
on all models.
Fig. 1: Charging System Wiring Schematic

Courtesy of MAZDA MOTORS CORP.
ADJUSTMENTS
BELT DEFLECTION
Measure belt deflection in center of longest pulley-to-pulley span. See BELT DEFLECTION
SPECIFICATIONS table. If belt deflection is not as specified, adjust as necessary.
BELT DEFLECTION SPECIFICATIONS
ApplicationDeflection - In. (mm)

1991 Mazda MX-5 Miata
ALTERNATOR & REGULATOR 1990-92 ELECTRICAL Alternators & Regulators - Mitsubishi

1991 Mazda MX-5 Miata
ALTERNATOR & REGULATOR 1990-92 ELECTRICAL Alternators & Regulators - Mitsubishi
Microsoft
Sunday, July 05, 2009 2:14:53 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.
Microsoft
Sunday, July 05, 2009 2:14:58 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.

TROUBLE SHOOTING
CHARGING SYSTEM
B2200
New Belt0.28-0.31 (7.0-8.0)
Used Belt0.31-0.35 (8.0-9.0)
B2600i
New Belt0.39-0.47 (10.0-12.0)
Used Belt0.43-0.51 (11.0-13.0)
Miata
New Belt0.31-0.35 (8.0-9.0)
Used Belt0.35-0.39 (9.0-10.0)
MPV
4-Cylinder Engine
New Belt0.39-0.47 (10-12)
Used Belt0.43-0.57 (11-13)
V6 Engine
New Belt0.35-0.39 (9-10)
Used Belt0.39-0.47 (10-12)
MX-3
4-Cylinder Engine
New Belt0.31-0.35 (8.0-9.0)
Used Belt0.35-0.39 (9.0-10.0)
V6 Engine
New Belt0.24-0.28 (6.0-7.0)
Used Belt0.28-0.31 (7.0-8.0)
MX-6 & 626
New Belt0.24-0.31 (6.0-8.0)
Used Belt0.28-0.35 (7.0-9.0)
Protege & 323
New Belt0.31-0.35 (8.0-9.0)
Used Belt0.35-0.39 (9.0-10.0)
RX7
New Belt0.47-0.59 (12.0-15.0)
Used Belt0.55-0.67 (14.0-17.0)
929
New Belt0.35-0.39 (9.0-10.0)
Used Belt0.39-0.47 (10.0-12.0)
- With 22 lbs. (98N) applied to belt.

1991 Mazda MX-5 Miata
ALTERNATOR & REGULATOR 1990-92 ELECTRICAL Alternators & Regulators - Mitsubishi
Microsoft
Sunday, July 05, 2009 2:14:54 PMPage 2 © 2005 Mitchell Repair Information Company, LLC.

CHARGING SYSTEM TROUBLE SHOOTING
TROUBLE SHOOTING PRECAUTIONS
Miata
Obtain code number and deactivate audio anti-theft system before disconnecting battery.
All Models
DO NOT reverse battery cable connections. Rectifier will be damaged.
DO NOT use high voltage type testers.
PROBLEM Possible CauseAction
NO START CONDITION
Dead BatteryCheck/Replace Battery
Bad Cable ConnectionsClean/Replace Cables
Ignition Switch/Circuit FaultCheck Switch/Circuit
CHARGING SYSTEM WARNING LIGHT STAYS ON
Loose/Worn Alternator BeltTighten/Replace Belt
Loose Alternator ConnectionsCheck/Repair
Connections
Warning Light WiringCheck/Repair Wiring
Faulty Stator/DiodesTest/Repair Alternator
Faulty Voltage RegulatorTest/Repair Regulator
WARNING LIGHT OFF WITH IGNITION SWITCH ON
Blown FuseCheck/Replace Fuse
Faulty AlternatorTest Alternator
Bad Warning Light BulbTest/Replace Bulb
WARNING LIGHT ON WITH IGNITION SWITCH OFF
Alternator Wiring ShortCheck/Repair Wiring
Faulty Rectifier BridgeTest/Repair Alternator
AMMETER INDICATES DISCHARGE
Loose/Worn Alternator BeltTighten/Replace Belt
Loose Alternator ConnectionsCheck/Repair
Connections
Faulty AmmeterTest/Replace Ammeter
NOISY Defective BatteryReplace Battery
Defective AlternatorTest/Repair Alternator
Defective RegulatorTest/Repair Regulator
NOTE: Observe the following precautions when trouble shooting or testing charging
system:

1991 Mazda MX-5 Miata
ALTERNATOR & REGULATOR 1990-92 ELECTRICAL Alternators & Regulators - Mitsubishi
Microsoft
Sunday, July 05, 2009 2:14:54 PMPage 3 © 2005 Mitchell Repair Information Company, LLC.

Battery voltage is always applied to terminal "B".
DO NOT ground terminal "L" while engine is running.
DO NOT start engine with connector disconnected from terminals "L" and "S".
DO NOT apply battery voltage to terminal "L".
ON-VEHICLE TESTING
ALTERNATOR OUTPUT
1. Connect an ammeter (80-amp minimum) in-line between terminal "B" connector and wire. See Fig. 2
,
Fig. 3
and Fig. 4 . Turn all headlights and accessories on and depress brake pedal. With engine operating
at 2500-3000 RPM, measure output amperage. NOTE: Check alternator wiring harness connections and drive belt tension. Battery
must be fully charged before testing. Wait at least 30 seconds after starting
engine before measuring system voltage.
CAUTION: Ensure alternator terminal "B" does not contact ground.

1991 Mazda MX-5 Miata
ALTERNATOR & REGULATOR 1990-92 ELECTRICAL Alternators & Regulators - Mitsubishi
Microsoft
Sunday, July 05, 2009 2:14:54 PMPage 4 © 2005 Mitchell Repair Information Company, LLC.

1990-93 ENGINE COOLING
Drive Belt Routing & Adjustment - MX-5 Miata
ADJUSTMENT
Fig. 1: Identifying Correct Belt Mounting
Courtesy of MAZDA MOTORS CORP.
ALTERNATOR
Loosen alternator bolts and adjust belt deflection by turning adjusting bolt. See Fig. 2
, Fig. 6 and Fig. 7 . See
ADJUSTMENT SPECIFICATIONS
. Tighten bolts to specification. See TORQUE SPECIFICATIONS. NOTE: Ensure drive belts are not worn, cracked or frayed and are correctly mounted
on pulleys. See Fig. 1
.
NOTE: If a new belt is used, adjust belt deflection at midpoint of new belt specification.

1991 Mazda MX-5 Miata
1990-93 ENGINE COOLING Drive Belt Routing & Adjustment - MX-5 Miata

1991 Mazda MX-5 Miata
1990-93 ENGINE COOLING Drive Belt Routing & Adjustment - MX-5 Miata
Microsoft
Sunday, July 05, 2009 2:14:16 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.
Microsoft
Sunday, July 05, 2009 2:14:28 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.

Fig. 2: Adjusting Alternator Belt
Courtesy of MAZDA MOTORS CORP.
A/C COMPRESSOR
Loosen locknut and adjust belt deflection by turning adjusting bolt. See Fig. 3
, Fig. 6 and Fig. 7 . See
ADJUSTMENT SPECIFICATIONS
. Tighten bolts to specification. See TORQUE SPECIFICATIONS.

1991 Mazda MX-5 Miata
1990-93 ENGINE COOLING Drive Belt Routing & Adjustment - MX-5 Miata
Microsoft
Sunday, July 05, 2009 2:14:16 PMPage 2 © 2005 Mitchell Repair Information Company, LLC.

Fig. 7: Identifying Drive Belt Routing & Deflection Check Point (3 Of 3)
Courtesy of MAZDA MOTORS CORP.
ADJUSTMENT SPECIFICATIONS
DEFLECTION SPECIFICATIONS
NOTE: Check belt deflection when engine is cold, or has bin off for 30 minutes.
Application(1) Specification - In. (mm)
New Belt (2)
Alternator0.31-0.35 (8-9)
A/C Compressor0.31-0.35 (8-9)
Power Steering Pump0.31-0.35 (8-9)
Used Belt
Alternator0.35-0.39 (9-10)
A/C Compressor0.35-0.39 (9-10)
Power Steering Pump0.35-0.39 (9-10)
(1)Deflection with 22 lbs. (10 kg) pressure applied midway on belt run.
Used on for less than 5 minutes.

1991 Mazda MX-5 Miata
1990-93 ENGINE COOLING Drive Belt Routing & Adjustment - MX-5 Miata
Microsoft
Sunday, July 05, 2009 2:14:16 PMPage 7 © 2005 Mitchell Repair Information Company, LLC.

TENSION SPECIFICATIONS
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS
(2)
Application(1) Specification - Lbs. (kg)
New Belt (2)
Alternator110-132 (50-60)
A/C Compressor110-132 (50-60)
Power Steering Pump110-132 (50-60)
Used Belt
Alternator95-110 (43-50)
A/C Compressor95-110 (43-50)
Power Steering Pump95-110 (43-50)
(1)Measure tension using Tension Gauge (49 9200 020), or equivalent.
(2)Used on for less than 5 minutes.
ApplicationFt. Lbs. (N.m)
Alternator Adjusting Bolt
"A"14-18 (19-25)
"B"27-38 (37-52)
A/C Compressor Locknut27-38 (37-52)
Power Steering Pump Adjusting Bolt
"A"23-44 (31-46)
"B"27-40 (37-54)
"C"14-18 (19-25)

1991 Mazda MX-5 Miata
1990-93 ENGINE COOLING Drive Belt Routing & Adjustment - MX-5 Miata
Microsoft
Sunday, July 05, 2009 2:14:16 PMPage 8 © 2005 Mitchell Repair Information Company, LLC.

table. Bleed air from system. Check fluid level. Check for leaks. Adjust alignment (if necessary).
POWER STEERING PUMP
Removal & Installation
1. Raise and support front of vehicle. On MX-6 and 626, remove right wheel and splash shield. On all
models remove belt, alternator and hydraulic lines from pump.
2. On Protege and 323, disconnect air cleaner duct and pressure switch. On all models, cap lines to prevent
contamination. Remove bracket-to-pump bolts.
3. To install, reverse removal procedure. Adjust belt tension. See POWER STEERING BELT
DEFLECTION TABLE under ADJUSTMENTS. Bleed air from system. Check for leaks.
OVERHAUL
STEERING GEAR
NOTE: See Fig. 2
-8 for exploded views of rack and pinion steering gears.

1991 Mazda MX-5 Miata
STEERING GEAR - POWER RACK & PINION 1991 STEERING Mazda - Power Rack & Pinion
Microsoft
Sunday, July 05, 2009 2:10:15 PMPage 6 © 2005 Mitchell Repair Information Company, LLC.

Courtesy of MAZDA MOTORS CORP.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS
ApplicationFt. Lbs. (N.m)
A/C Compressor Bracket
MX-3, Protege & 32317-26 (23-35)
MX-5 Miata11-16 (15-22)
Alternator Top Bolt27-38 (37-52)
Camshaft Sprocket Bolt36-45 (49-61)
Crankshaft/Timing Belt Sprocket Bolt
1986-9180-87 (109-118)
1992-95116-123 (157-167)
Power Steering Pump-To-Bracket Bolt
MX-3, Protege & 32327-38 (37-52)
Timing Belt Tensioner Bolt
DOHC27-38 (37-52)
SOHC14-19 (19-26)
INCH Lbs. (N.m)
Camshaft/Rocker Cover Bolt
DOHC & SOHC (Top)43-78 (5-9)
SOHC (Timing Belt Cover-To-Camshaft Cover)69-95 (8-11)
Crankshaft Pulley Bolts109-152 (12-17)

1991 Mazda MX-5 Miata
MAZDA 1.6L & 1.8L 4-Cylinder - 1986-95
Microsoft
Sunday, July 05, 2009 2:12:44 PMPage 11 © 2005 Mitchell Repair Information Company, LLC.