window MAZDA MODEL 2 2012 Owner's Guide

Black plate (253,1)
Body Lubrication
All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the hood's secondary latch
keeps the hood from opening when the
primary latch is released.
Wiper Blades
CAUTION
ØHot waxes applied by automatic
car washers have been known to
affect the wiper's ability to clean
windows.
Ø To prevent damage to the wiper
blades, do not use gasoline,
kerosene, paint thinner, or other
solvents on or near them.
Ø When the wiper lever is in the
AUTO position and the ignition is
switched ON, the wipers may
move automatically in the
following cases:
ØIf the windshield above the rain
sensor is touched.
ØIf the windshield above the rain
sensor is wiped with a cloth.
ØIf the windshield is struck with
a hand or other object.
ØIf the rain sensor is struck with
a hand or other object from
inside the vehicle.
Be careful not to pinch hands or
fingers as it may cause injury, or
damage the wipers. When
washing or servicing your Mazda,
make sure the wiper lever is in the
OFF position.
Contamination of either the windshield or
the blades with foreign matter can reduce
wiper effectiveness. Common sources are
insects, tree sap, and hot wax treatments
used by some commercial car washes.
If the blades are not wiping properly,
clean the window and blades with a good
cleaner or mild detergent; then rinse
thoroughly with clean water. Repeat if
necessary.
Maintenance and Care
Owner Maintenance
8-19
Mazda2_8CC7-EA-11H_Edition2 Page253
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (255,1)
CAUTION
ØDon't bend or discard the
stiffeners. You need to use them
again.
Ø If the metal stiffeners are
switched, the blade's wiping
efficiency could be reduced.
So don't use the driver's side metal
stiffeners on the passenger's side,
or vice versa.
Ø Be sure to reinstall the metal
stiffeners in the new blade rubber
so that the curve is the same as it
was in the old blade rubber.
4. Carefully insert the new blade rubber. Then install the blade assembly in the
reverse order of removal.
NOTE
Install the blade so that the tabs are toward the
bottom of the wiper arm.
qReplacing Rear Window Wiper
Blade
When the wiper no longer cleans well, the
blade is probably worn or cracked.
Replace it.
CAUTION
To prevent damage to the wiper arm
and other components, do not try to
sweep the wiper arm by hand.
1. Raise the wiper arm.
NOTE
The wiper arm will not remain lifted off the
rear window after being pulled up.
When replacing the wiper blade, continue
holding the wiper arm with one hand during
the work.
2. Firmly rotate the wiper blade to the right until it unlocks, then remove the
blade.
Maintenance and Care
Owner Maintenance
8-21
Mazda2_8CC7-EA-11H_Edition2 Page255
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (256,1)
CAUTION
To prevent damage to the rear
window let the wiper arm down
easily, do not let it slap down on the
rear window.
3. Pull down the blade rubber and slide it out of the blade holder.
4. Remove the metal stiffeners from each
blade rubber and install them in the
new blade.
CAUTION
Do not bend or discard the stiffeners.
You need to use them again. 5. Carefully insert the new blade rubber.
Then install the blade assembly in the
reverse order of removal.
8-22
Maintenance and Care
Owner Maintenance
Mazda2_8CC7-EA-11H_Edition2 Page256
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (276,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 FUEL HEAT ――
2 FUEL PUMP 15 A Fuel pump
3 F.FOG 15 A Fog lights
í
4 P/W 20 A Power windows
5 HORN 10 A Horn
6 EGI 10 A Engine control system
7 DSC-P 30 A DSC
8 DSC-V 20 A DSC
9 MAG 7.5 A Air conditioner
10 TAIL 15 A Taillights, Parking lights, License plate lights
11 STOP 10 A Brake lights
12 SWS 7.5 A Air bag
13 R.DEF 20 A Rear window defroster
14 HAZARD 10 A Hazard warning flashers, Turn signal lights
15 D/L 20 A Power door locks
16 EOP ――
17 ENG BAR 15 A Engine control system
8-42
Maintenance and Care
íSome models.
Owner Maintenance
Mazda2_8CC7-EA-11H_Edition2 Page276
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (278,1)
Fuse block (Left side)
DESCRIPTIONFUSE
RATING PROTECTED COMPONENT
1 TCM ――
2 ILLUMI 7.5 A Dashboard illumination
3 CIGAR 15 A Accessory Socket
4 MIRROR 7.5 A Power control mirror
5 M.DEF 7.5 A Mirror defroster
í
6 S.WARM ――
7 A/C 7.5 A Air conditioner
8 F.WIP 20 A Front window wiper and washer
9 R.WIP 10 A Rear window wiper and washer
10 STARTER ――
11 METER 2 ――
12 ENG 10 A Engine control system
13 METER 10 A Instrument cluster
14 SAS 10 A Air bag
15 AUDIO 3 ――
16 P/W 30 A Power windows
8-44
Maintenance and Care
íSome models.
Owner Maintenance
Mazda2_8CC7-EA-11H_Edition2 Page278
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (282,1)
CAUTION
ØDo not use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or
caustic agents on chrome-plated
or anodized aluminum parts. This
may damage the protective
coating; also, cleaners and
detergents may discolor or
deteriorate the paint.
Ø To prevent damaging the antenna,
remove it before entering a car
wash facility or passing beneath a
low overhead clearance.
Pay special attention to removing salt,
dirt, mud, and other foreign material from
the underside of the fenders, and make
sure the drain holes in the lower edges of
the doors and rocker panels are clean.
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Do not allow
soap to dry on the finish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.
WARNING
Dry off brakes that have become wet
by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the brake
performance returns to normal: Driving with wet brakes is
dangerous. Increased stopping
distance or the vehicle pulling to one
side when braking could result in a
serious accident. Light braking will
indicate whether the brakes have
been affected.
When using a high water pressure car
wash
High water temperature and high water
pressure car washers are available
depending on the type of car wash
machine. If the car washer nozzle is put
too close to the vehicle, the force of the
spray could damage or deform the
molding, affect the sealability of parts,
and allow water to penetrate the interior.
Keep a sufficient space (30 cm or more)
between the nozzle and the vehicle. In
addition, do not spend too much time
spraying the same area of the vehicle, and
be very careful when spraying between
gaps in doors and around windows.
Waxing
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.
1. Use wax which contains no abrasives. Waxes containing abrasive will remove
paint and could damage bright metal
parts.
8-48
Maintenance and Care
Appearance Care
Mazda2_8CC7-EA-11H_Edition2 Page282
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (287,1)
qCleaning the Window Interiors
If the windows become covered with an
oily, greasy, or waxy film, clean them
with glass cleaner. Follow the directions
on the container.
CAUTION
Ø Do not scrape or scratch the inside
of the window glass. It could
damage the thermal filaments.
Ø When washing the inside of the
window glass, use a soft cloth
dampened in lukewarm water,
gently wiping the thermal
filaments.
Use of glass cleaning products
could damage the thermal
filaments.
qCleaning the Floor Mats
Rubber floor mats should be cleaned with
mild soap and water only.
WARNING
Do not use rubber cleaners, such as tire
cleaner or tire shine, when cleaning
rubber floor mats:
Cleaning the rubber floor mats with
rubber cleaning products makes the
floor mats slippery.
This may cause an accident when
depressing the accelerator, brake, or
clutch (Manual transaxle) pedal or
when getting in or out of the vehicle.
After removing the floor mats for
cleaning, always reinstall them
securely.Refer to Floor Mat on page 4-7.
Maintenance and Care
Appearance Care
8-53
Mazda2_8CC7-EA-11H_Edition2 Page287
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (339,1)
Personalization Features
The following“Personalization Features ”are available. These settings can only be changed by an Authorized
Mazda Dealer.
Item Feature Factory Setting Available Settings
Auto headlight on/off The headlight illumination on/off timing based
on surrounding lightness/darkness can be
changed Standard
(Illuminates under average levels of
darkness) Earlier/
Somewhat earlier/ Somewhat later/
Later
Two-step down
power window The two-step down power window function can
be changed
Activated Deactivated
Adjusts the window opening range 3 cm (1 in) 2―10 cm (0.8― 3.9 in)
Personalization Features
10-7
Mazda2_8CC7-EA-11H_Edition2 Page339
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (343,1)
D
DefrosterMirror ......................................... 5-58
Rear window .............................. 5-58
Dimensions ....................................... 10-5
Door Locks ......................................... 3-8
Driving In Flooded Area ................... 4-10
Driving on Uneven Road .................. 4-11
Driving Tips ........................................ 4-6 Automatic transaxle ................... 5-14
Break-in period ............................ 4-6
Driving in flooded area .............. 4-10
Driving on uneven road .............. 4-11
Hazardous driving ........................ 4-7
Money-saving suggestions ........... 4-6
Rocking the vehicle ...................... 4-8
Winter driving .............................. 4-8
Dynamic Stability Control (DSC) ..... 5-21 DSC OFF indicator light ............ 5-22
DSC OFF switch ........................ 5-22
TCS/DSC indicator light ............ 5-21
E
Emergency Starting ........................... 7-17Flooded engine ........................... 7-17
Jump-starting .............................. 7-18
Push-starting .............................. 7-21
Emergency Towing ........................... 7-22
Emission Control System .................... 4-3
Engine Coolant ....................................... 8-13
Exhaust gas .................................. 4-4
Hood release .............................. 3-20
Oil .............................................. 8-12
Overheating ................................ 7-15
Starting ......................................... 5-3
Engine Compartment Overview ........ 8-11
E
Engine Coolant Overheating ................................ 7-15
Event Data Recorder ......................... 9-19
Exhaust Gas ........................................ 4-4
Exterior Care ..................................... 8-47
F
Flasher Hazard warning .......................... 5-59
Headlights .................................. 5-50
Flat Tire ............................................... 7-3 Changing ...................................... 7-6
Spare tire and tool storage ............ 7-3
Fluids Classification .............................. 10-4
Owner maintenance ..................... 8-8
Fog Lights ......................................... 5-53
Foot Brake .......................................... 5-5
Front Seats .......................................... 2-2
Fuel Filler lid and cap ........................ 3-19
Gauge ......................................... 5-31
Requirements ............................... 4-2
Tank capacity ............................. 10-4
Fuses ................................................. 8-39 Panel description ........................ 8-42
Replacement ............................... 8-39
G
Gauges .............................................. 5-29
Glove Compartment .......................... 6-41
H
Hazard Warning Flasher .................... 5-59
Hazardous Driving .............................. 4-7
Index
11-3
Mazda2_8CC7-EA-11H_Edition2 Page343
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (345,1)
O
Overloading ...................................... 4-10
P
Paint Damage .................................... 8-45
Parking Brake ..................................... 5-6
Parking in an Emergency .................... 7-2
Personalization Features ................... 10-7
Power Door Locks .............................. 3-9
Power Steering .................................. 5-15Power steering malfunction indicator
light ............................................ 5-15
Power Windows ................................ 3-16
Push-Starting ..................................... 7-21
R
Rear Door Child Safety Locks .......... 3-11
Rear Seat ............................................. 2-4
Rear Window Defroster .................... 5-58
Rear Window Washer ....................... 5-57
Rear Window Wiper .......................... 5-57
Rearview Mirror ................................ 3-27
Recreational Towing ......................... 7-24
Registering Your Vehicle in A Foreign
Country ............................................. 9-16
Rocking the Vehicle ............................ 4-8
S
Safety Defects, Reporting ................. 9-41
S
Seat Belt System 3-point type ................................ 2-13
Automatic locking ...................... 2-12
Emergency locking .................... 2-11
Extender ..................................... 2-17
Pregnant women ......................... 2-11
Pretensioner and load limiting .... 2-15
Seat belt precautions .................... 2-9
Seat belt reminder ....................... 2-19
Warning light ............................. 2-19
Seats Front seat ...................................... 2-2
Head restraint ............................... 2-7
Rear seat ....................................... 2-4
Security System
Immobilizer system .................... 3-23
Service Publications .......................... 9-43
Spare Tire and Tool Storage ................ 7-3
Specifications .................................... 10-4
Speedometer ...................................... 5-30
SRS Air Bags Driver and front passenger occupant
classification system .................. 2-50
How the SRS air bags work ....... 2-42
Limitations to SRS air bag ......... 2-48
Monitoring and maintenance ..... 2-55
SRS air bag deployment
criteria ........................................ 2-47
Supplemental restraint system
(SRS) precautions ...................... 2-36
Supplemental restraint system
components ................................ 2-41
Starting the Engine .............................. 5-3
Steering Wheel .................................. 3-26 Horn ........................................... 5-59
Storage Compartments ...................... 6-41 Center Console Tray ................... 6-41
Glove Compartment ................... 6-41
Index
11-5
Mazda2_8CC7-EA-11H_Edition2 Page345
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H