bulb MAZDA MODEL 3 4-DOOR 2005 User Guide

Black plate (283,1)
2. Detach the electrical connector fromthe unit by pulling it to the rear.
3. Install the new side turn signal unit in
the reverse order of removal.
NOTE
Bulb replacement is not possible
because it is built into the unit. Replace
the unit.
Brake lights/Taillights, Rear turn signal
lights (4 Door)
1. Pull the center of each plastic retainerand remove the retainers and the trunk
end trim.
Removal
Installation
2. Pull the center of each plastic retainer and remove the retainers and partially
open the trunk side trim.
Removal
Installation
3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Disconnect the bulb from the socket.
Brake lights/TaillightsRear turn signal lights
5. Install the new bulb in the reverse order of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Maintenance and Care
Owner Maintenance
8-41
Mazda3_8T96-EA-04J_Edition3 Page283
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (284,1)
Brake lights/Taillights(5 Door)
With LED bulb
Due to the complexity and difficulty of
the procedure, the LED bulbs should be
replaced by an Authorized Mazda Dealer.
NOTE
LED bulb replacement is not possible.
The rear combination component must
be replaced.
With Non-LED bulb
1. Remove the cover.
Left side
Right side
2. Turn the socket and bulb assembly counterclockwise and remove it. 3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Rear turn signal lights (5 Door)
1. Remove the cover.
Left side
8-42
Maintenance and Care
Owner Maintenance
Mazda3_8T96-EA-04J_Edition3 Page284
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (285,1)
Right side
2. Turn the socket and bulb assemblycounterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Reverse light
4 Door
1. Pull the center section of the plasticretainer and remove the retainers, then
remove the trunk rear trim.
Removal
Installation
2. Turn the socket and bulb assembly counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Maintenance and Care
Owner Maintenance
8-43
Mazda3_8T96-EA-04J_Edition3 Page285
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (286,1)
5 Door
1. Remove the cover.
2. Turn the socket and bulb assemblycounterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
High-mount brake light
4 Door
1. Pull the center of each plastic retainer
and remove the retainers and the trunk
rear trim.
Removal
Installation
2. Disconnect the electrical connector from the socket.
3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
8-44
Maintenance and Care
Owner Maintenance
Mazda3_8T96-EA-04J_Edition3 Page286
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (287,1)
5 Door
1. Remove the liftgate upper trim.
2. Disconnect the electrical connectorfrom the socket.
3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
License plate lights
1. Wrap a flathead screwdriver with a softcloth to prevent damage to the lens and
remove the lens by carefully prying on
the edge of the lens with a flathead
screwdriver.
2. Disconnect the bulb by pulling it out.
Edge
3. Install the new bulb in the reverse order of removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights (Front)í
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the overhead light as
shown in the figure, and then remove
the overhead light unit.
Maintenance and Care
Owner Maintenance
8-45íSome models.
Mazda3_8T96-EA-04J_Edition3 Page287
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (288,1)
2. Turn the socket and bulb assemblycounterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
Overhead light (Rear)
1. Wrap a small flathead screwdriver witha soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
flathead screwdriver.
2. Disconnect the bulb by pulling it out.
Edge
3. Install the new bulb in the reverse order of removal.
Trunk light (4 Door)
1. Press both sides of the lens cap toremove it.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order of removal.
Luggage compartment light (5 Door)
1. Insert your finger as shown in thefigure and remove the unit.
2. Wrap a small flathead screwdriver witha soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
flathead screwdriver.
8-46
Maintenance and Care
Owner Maintenance
Mazda3_8T96-EA-04J_Edition3 Page288
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (289,1)
3. Disconnect the bulb by pulling it out.
4. Install the new bulb in the reverse orderof removal.
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the front
passenger's side below the glove box
If the electrical system doesn't work, first
inspect fuses on the front passenger's side
below the glove box.
1. Turn off the ignition switch and other
switches.
2. Remove the cover.
Maintenance and Care
Owner Maintenance
8-47
Mazda3_8T96-EA-04J_Edition3 Page289
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (328,1)
2.3-liter engineItem Weight
Manual transaxle Automatic transaxle
GVWR (Gross Vehicle Weight Rating) 1,732 kg (3,818 lb) 1,760 kg (3,880 lb)
GAWR (Gross Axle Weight Rating) Front 928 kg (2,046 lb) 957 kg (2,110 lb)
Rear 804 kg (1,772 lb) 803 kg (1,770 lb)
5 Door
Item Weight
Manual transaxle Automatic transaxle
GVWR (Gross Vehicle Weight Rating) 1,743 kg (3,843 lb) 1,771 kg (3,904 lb)
GAWR (Gross Axle Weight Rating) Front 930 kg (2,050 lb) 960 kg (2,116 lb)
Rear 813 kg (1,793 lb) 811 kg (1,788 lb)
q
Air Conditioner
Gas complies with SAE J639 Maximum operating charge
HFC134a (R-134a) 0.5 kg (17.55 oz)
qLight Bulbs
Exterior light
Light bulb Category
Wattage ECE R SAE
Headlights High beam 60 HB3
―
Low beam Halogen 55 H7
―
Xenon fusion 35 D2S ―
Front turn signal lights/Side-marker lights 27/8 ―#1157NA
Fog lights
í55 H11 ―
Side turn signal lights*15 WY5W ―
High-mount brake light 18 W16W #921
Rear turn signal lights 21 W21W #7440
Brake lights/Taillights With Non-LED bulb 21/5 W21/5W #7443
With LED bulb
*24/0.8
――
Reverse light 21 W21W #7440
License plate light 5 W5W ―
*1 Bulb replacement is not possible because it is built into the unit. Replace the unit.
*2 Bulb replacement is not possible. The rear combination component must be replaced.
10-6íSome models.
Specifications
Mazda3_8T96-EA-04J_Edition3 Page328
Wednesday, May 11 2005 3:40 PM
Form No.8T96-EA-04J

Black plate (329,1)
Interior lightLight bulb Category
Wattage ECE R
Trunk light (Sedan)
5W5W
Luggage compartment light (Hatchback) ―
Overhead light/Map lights (Front)
íW5W
Overhead light (Rear) 10 ―
qTires
NOTE
The tires have been optimally matched with the chassis of your vehicle.
When replacing tires, Mazda recommends that you replace tires of the same type
originally fitted to your vehicle. For details, contact an Authorized Mazda Dealer.
Check the tire pressure label for tire size and inflation pressure. Refer to Tire Inflation
Pressure on page 8-32.
Standard tire Tire size Inflation pressure
Front Rear
195/65R15 91V 220 kPa (2.2 kgf/cm
2, 32 psi or lb/po2) 220 kPa (2.2 kgf/cm2, 32 psi or lb/po2)
P195/65R15 89H 230 kPa (2.3 kgf/cm2, 33 psi or lb/po2) 230 kPa (2.3 kgf/cm2, 33 psi or lb/po2)
205/55R16 91V
220 kPa (2.2 kgf/cm
2, 32 psi or lb/po2) 220 kPa (2.2 kgf/cm2, 32 psi or lb/po2)
P205/55R16 89H
205/50R17 89V
P205/50R17 88V
Temporary spare tire Tire size Inflation pressure
T115/70D15 420 kPa (4.2 kgf/cm
2or bar, 60 psi)
T125/70D16
q Fuses
Refer to the fuse rating on page 8-47.
Specifications
10-7íSome models.
Mazda3_8T96-EA-04J_Edition3 Page329
Wednesday, May 11 2005 3:40 PM
Form No.8T96-EA-04J

Black plate (332,1)
A
Add-On Non-Genuine Parts and
Accessories ....................................... 9-13
Air Bag Systems ............................... 2-38
Air Filter ............................................ 8-24
Antenna ............................................. 6-10
Anti-Lock Brake System (ABS) ......... 5-6Warning light ............................... 5-7
Appearance Care ............................... 8-54
Ashtray .............................................. 6-43
Audio System ................................... 6-10 Audio control switch .................. 6-34
Operating tips for audio
system ........................................ 6-10
Safety certification ..................... 6-37
Automatic Transaxle Driving tips ................................ 5-16
Fluid ........................................... 8-21
Manual shift mode ..................... 5-13
Shift-lock override ..................... 5-12
Shift-lock system ....................... 5-12
Transaxle ranges ......................... 5-11
B
BatteryEmergency starting .................... 7-14
Maintenance ............................... 8-29
Specifications ............................. 10-4
Beep Sounds
Ignition key reminder ................. 5-44
Beeps Lights-on reminder ..................... 5-44
Seat belt warning beep Sounds ... 5-44
Tire inflation pressure warning
beep ............................................ 5-44
Before Starting the Engine .................. 4-6 After getting in ............................. 4-6
Before getting in .......................... 4-6
B
Body Lubrication .............................. 8-24
Bottle Holder ..................................... 6-45
Brake/Clutch
Fluid ........................................... 8-20
Brakes Anti-lock brake system (ABS) ..... 5-6
Brakes assist ................................. 5-8
Foot brake .................................... 5-4
Parking brake ............................... 5-5
Warning light ............................... 5-6
Break-In Period ................................... 4-7
Bulb Replacement ............................. 8-37
C
Capacities .......................................... 10-5
Carbon Monoxide ............................... 4-5
Cargo Securing Loops ...................... 6-46
Cargo Sub-Compartment .................. 6-46
Catalytic Converter ............................. 4-3
Cell Phones ....................................... 9-14
Center Console .................................. 6-46
Child Restraint Child restraint precautions ......... 2-21
Installing child-restraint
systems ....................................... 2-25
LATCH child-restraint
systems ....................................... 2-33
Child Safety Locks for Rear Doors ..... 3-9
Cigarette Lighter ............................... 6-43
Climate Control System ...................... 6-2 Gas specifications ...................... 10-6
Clock ................................................. 6-42
Cruise Control ................................... 5-18
Cup Holder ........................................ 6-44
Customer Assistance ........................... 9-2
11-2
Index
Mazda3_8T96-EA-04J_Edition3 Page332
Wednesday, May 11 2005 3:40 PM
Form No.8T96-EA-04J