ignition MAZDA MODEL 3 4-DOOR 2011 Owners Manual

Black plate (429,1)
2. Pull the center of each plastic retainerand remove the retainers and the trunk
end trim.
InstallationRemoval
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal.
(5 Door)
LED type
Due to the complexity and difficulty of
the procedure, the LED bulbs should be
replaced by an Authorized Mazda Dealer.
NOTE
LED bulb replacement is not possible. The
rear combination component must be replaced.
Bulb type
1. Make sure the ignition is switched off, and the headlight switch is off.
2. Remove the liftgate upper trim.
3. Disconnect the electrical connector from the bulb by pressing the tab on
the connector with your finger and
pulling the connector sideward to the
left.
4. Turn the socket and bulb assemblycounterclockwise and remove it.
Maintenance and Care
Owner Maintenance
8-51
Mazda3_8BM5-EA-10F_Edition3 Page429
Tuesday, October 5 2010 9:8 AM
Form No.8BM5-EA-10F

Black plate (430,1)
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse orderof removal.
License plate lights
1. Make sure the ignition is switched off,and the headlight switch is off.
2. Wrap a flathead screwdriver with a soft cloth to prevent damage to the lens,
and then remove the lens by carefully
prying on the edge of the lens with a
flathead screwdriver.
3. Disconnect the bulb by pulling it out.
4. Install the new bulb in the reverse orderof removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights (Front),
Overhead light (Rear), Vanity mirror
lightsí
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens, and then remove the lens by
carefully prying on the edge of the lens
with the flathead screwdriver.
2. Disconnect the bulb by pulling it out.
Overhead light/Map lights (Front)
8-52
Maintenance and Care
íSome models.
Owner Maintenance
Mazda3_8BM5-EA-10F_Edition3 Page430
Tuesday, October 5 2010 9:8 AM
Form No.8BM5-EA-10F

Black plate (432,1)
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the vehicle's left
side
If the electrical system does not work,
first inspect the fuses on the vehicle's left
side.
1. Make sure the ignition is switched off,
and other switches are off.
2. Remove the cover.
3. Pull the fuse straight out with the fuse puller provided on the inside of the
engine compartment fuse block cover.
4. Inspect the fuse and replace it if it'sblown.
Normal Blown
5. Insert a new fuse of the same amperage
rating, and make sure it fits tightly. If it
does not fit tightly, have an expert
install it. We recommend an
Authorized Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or CIGAR circuit.
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
8-54
Maintenance and Care
Owner Maintenance
Mazda3_8BM5-EA-10F_Edition3 Page432
Tuesday, October 5 2010 9:8 AM
Form No.8BM5-EA-10F

Black plate (433,1)
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses in
the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Make sure the ignition is switched off,and other switches are off.
2. Remove the fuse block cover.
3. If any fuse but the MAIN fuse is blown, replace it with a new one of the
same amperage rating .
Normal
Blown
WARNING
Do not replace the main fuse by
yourself. Have an Authorized Mazda
Dealer perform the replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse is
a high current fuse. Incorrect
replacement could cause an electrical
shock or a short circuit resulting in a
fire.
Maintenance and Care
Owner Maintenance
8-55
Mazda3_8BM5-EA-10F_Edition3 Page433
Tuesday, October 5 2010 9:8 AM
Form No.8BM5-EA-10F

Black plate (440,1)
Exterior Care
Followalllabel and container directions
when using a chemical cleaner or polish.
Read all warnings and cautions.
q Maintaining the Finish
Washing
CAUTION
When the wiper lever is in the AUTO
position and the ignition switch is in
the ON position, the wipers may
move automatically in the following
cases:
Ø If the windshield above the rain
sensor is touched.
Ø If the windshield above the rain
sensor is wiped with a cloth.
Ø If the windshield is struck with a
hand or other object.
Ø If the rain sensor is struck with a
hand or other object from inside
the vehicle.
Be careful not to pinch hands or
fingers as it may cause injury, or
damage the wipers. When washing
or servicing your Mazda, make sure
the wiper lever is in the OFF position.
To help protect the finish from rust and
deterioration, wash your Mazda
thoroughly and frequently, at least once a
month, with lukewarm or cold water.
If the vehicle is washed improperly, the
paint surface could be scratched. Here are
some examples of how scratching could
occur. Scratches occur on the paint surface
when:
lThe vehicle is washed without first
rinsing off dirt and other foreign
matter.
lThe vehicle is washed with a rough,
dry, or dirty cloth.
lThe vehicle is washed at a car wash
that uses brushes that are dirty or too
stiff.
lCleansers or wax containing abrasives
are used.
NOTE
lMazda is not responsible for scratches
caused by automatic car washes or
improper washing.
lScratches are more noticeable on vehicles
with darker paint finishes.
To minimize scratches on the vehicle's
paint finish:
lRinse off any dirt or other foreign
matter using lukewarm or cold water
before washing.
lUse plenty of lukewarm or cold water
and a soft cloth when washing the
vehicle. Do not use a nylon cloth.
lRub gently when washing or drying the
vehicle.
lTake your vehicle only to a car wash
that keeps its brushes well maintained.
lDo not use abrasive cleansers or wax
that contain abrasives.
CAUTION
Do not use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or anodized
aluminum parts. This may damage
the protective coating; also, cleaners
and detergents may discolor or
deteriorate the paint.
8-62
Maintenance and Care
Appearance Care
Mazda3_8BM5-EA-10F_Edition3 Page440
Tuesday, October 5 2010 9:8 AM
Form No.8BM5-EA-10F

Black plate (504,1)
Personalization Features
The following“Personalization Features ”are available. These settings can only be changed by an Authorized
Mazda Dealer.
Setting Available customization Initial Setting After Setting Change
Auto headlight on/off The headlight illumination on/off timing based
on the surrounding lightness/darkness can be
changed. 2000
―4000 lx 1000 ―2000 lx
Turn indicator The volume level of the turn indicator can be
changed. High Low/Deactivated
Key reminder
warning alarm The volume of the key reminder warning alarm
can be changed.
High Low
Lights-on reminder
warning alarm
*1The volume of the lights-on reminder warning
alarm can be changed. High Low/Deactivated
Illumination entry The time required for the interior lamp to turn
off automatically after all the doors are closed
can be changed.
15 seconds 7.5/30/60 seconds
The function allowing the interior lamp to
illuminate automatically when the ignition is
switched off can be deactivated. Activated Deactivated
The function allowing the interior lamp to
illuminate automatically when the doors are
unlocked can be deactivated. Activated Deactivated
The time required for the interior lamp to turn
off automatically can be changed
(prevents battery depletion when a door is
open/ajar). 30 minutes 10/60 minutes
The time required for the interior lamp to
illuminate after unlocking any door can be
changed. 30 seconds 7.5/15/60 seconds
The function allowing the interior lamp to turn
off automatically when any door is opened
(or not securely closed) can be changed. Activated Deactivated
Smart turn The function allowing the turn signal lights to
flash three times with a momentary turn switch
operation (when changing lanes) can be
activated. Deactivated Activated
10-12
Personalization Features
Mazda3_8BM5-EA-10F_Edition3 Page504
Tuesday, October 5 2010 9:8 AM
Form No.8BM5-EA-10F

Black plate (505,1)
SettingAvailable customization Initial Setting After Setting Change
Power door locks The vehicle-speed-response auto lock function
can be deactivated.
Activated Deactivated
Locking/unlocking of the doors can be set in
conjunction with the selector lever position. Deactivated1. Not in Park (P)
position: Lock all
doors
Park (P) position:
Unlock all doors
2. Not in Park (P)
position: Lock all
doors
Park (P) position:
Unlock the driver's
door only
3. Not in Park (P)
position: Lock all
doors
Park (P) position:
Inoperable
The function for unlocking the doors
simultaneously when the ignition is switched
off can be changed. Unlock all doors
Unlock driver's
door/Inoperable
Keyless entry The method for unlocking doors using the
retractable key can be selected.
Press × 2 Press × 1
The time required for the doors to relock
automatically after unlocking with the
transmitter can be changed. 30 seconds 60/90 seconds
The function allowing the horn to sound
automatically when the doors are locked by
pressing the transmitter two times consecutively
can be deactivated. Activated Deactivated
The hazard warning lights can be deactivated so
that they do not flash when the doors are
locked/unlocked. Activated Deactivated
Personalization Features
10-13
Mazda3_8BM5-EA-10F_Edition3 Page505
Tuesday, October 5 2010 9:8 AM
Form No.8BM5-EA-10F

Black plate (506,1)
SettingAvailable customization Initial Setting After Setting Change
Advanced keyless
entry The function to automatically lock doors when
leaving the vehicle while carrying the key can
be activated.
Deactivated Activated
The advanced key's remaining battery level
warning light in the instrument cluster can be
deactivated. Activated Deactivated
The volume of the answer-back beep during
keyless entry system operation can be adjusted. High Low/Deactivated
The volume of the warning beep for the
advanced keyless entry system can be adjusted. High
Low
The function allowing the power supply to turn
off automatically after the ignition has been left
in the ACC position for a long period of time
can be deactivated. Activated Deactivated
A transition pattern in which the ignition
position can be switched when pressing the
push button start can be selected. ON
→Off ON →ACC →Off
The advanced key function can be deactivated. Activated Deactivated
The method for unlocking the doors using the
request switch can be selected. Press × 2 Press × 1
*1 Without auto-light control function
The following “Personalization Features ”can be changed the vehicle owner.
Setting FunctionInitial Setting After Setting Change
Multi information
display The display language can be selected. 6-110
English, French,
or Spanish
English/German/French/Italian/ Spanish
The distance unit can be changed. 6-110 mile or km km or mile
The temperature unit can be changed. 6-110 °F or °C °C or °F
10-14
Personalization Features
Mazda3_8BM5-EA-10F_Edition3 Page506
Tuesday, October 5 2010 9:8 AM
Form No.8BM5-EA-10F

Black plate (508,1)
A
Accessory Socket ............................ 6-116
Adaptive Front Lighting System
(AFS) ................................................ 5-63
Add-On Non-Genuine Parts and
Accessories ....................................... 9-19
Advanced Key ..................................... 3-2Advanced key maintenance ......... 3-5
Advanced key suspend
function ...................................... 3-21
Auxiliary key .............................. 3-21
Locking, unlocking with request
switch ........................................... 3-9
Opening the liftgate/trunk lid ..... 3-11
Operational range ......................... 3-7
Remote control function ............. 3-17
Service ......................................... 3-7
Warning and beep sounds .......... 3-22
When warning indicator/beep is
activated ..................................... 3-25
Air Bag Systems ............................... 2-43
Antenna ............................................. 6-18
Anti-Lock Brake System (ABS) ......... 5-8 Warning light ............................... 5-9
Appearance Care ............................... 8-60
Audio System ................................... 6-18 Audio control switch .................. 6-58
Audio set .................................... 6-29
AUX mode ................................. 6-61
Operating tips for audio
system ........................................ 6-19
Safety certification ..................... 6-63
Automatic Transaxle Driving tips ................................ 5-19
Fluid ........................................... 8-24
Manual shift mode ..................... 5-16
Shift-lock override ..................... 5-15
Shift-lock system ....................... 5-15
Transaxle ranges ........................ 5-14
B
BatteryEmergency starting .................... 7-18
Maintenance ............................... 8-31
Specifications ............................. 10-4
Beep Sounds Ignition key reminder ................. 5-57
Lights-on reminder ..................... 5-57
Seat belt warning ........................ 5-57
Tire inflation pressure warning ... 5-58
Before Starting the Engine .................. 4-6 After getting in ............................. 4-6
Before getting in .......................... 4-6
Bluetooth Audio ............................... 6-64
Bluetooth Hands-Free ....................... 6-74 Basic Bluetooth Hands-Free
operation .................................... 6-78
Convenient use of the hands-free
system ........................................ 6-83
Hands-free setting ...................... 6-89
Mazda Bluetooth Hands-Free
customer service ......................... 6-96
Safety certification ..................... 6-96
When Bluetooth Hands-Free cannot
be used ....................................... 6-95
Body Lubrication .............................. 8-27
Boost Gauge ..................................... 5-39
Bottle Holder ................................... 6-112
Brake/Clutch Fluid ........................................... 8-23
Brakes Anti-lock brake system (ABS) ..... 5-8
Brakes assist ............................... 5-10
Foot brake .................................... 5-5
Parking brake ............................... 5-7
Warning light ............................... 5-8
Break-In Period ................................... 4-7
Bulb Replacement ............................. 8-42
11-2
Index
Mazda3_8BM5-EA-10F_Edition3 Page508
Tuesday, October 5 2010 9:8 AM
Form No.8BM5-EA-10F

Black plate (510,1)
F
FlasherHazard warning .......................... 5-71
Headlights .................................. 5-59
Flat Tire ............................................... 7-3 Changing ...................................... 7-9
Spare tire and tool storage ............ 7-3
Fluids Classification .............................. 10-4
Owner maintenance ................... 8-15
Fog Lights ......................................... 5-65
Foot Brake .......................................... 5-5
Front Seats
(Electrically Operated Seats) ............... 2-4
Front Seats
(Manually Operated Seats) ................. 2-2
Fuel Filler lid and cap ........................ 3-47
Gauge ......................................... 5-38
Requirements ............................... 4-2
Tank capacity ............................. 10-5
Fuses ................................................. 8-54 Panel description ........................ 8-56
Replacement ............................... 8-54
G
Gauges .............................................. 5-36
Glove Compartment ........................ 6-113
H
Hazard Warning Flasher .................... 5-71
Hazardous Driving .............................. 4-8
H
HeadlightsControl ....................................... 5-59
Flashing ...................................... 5-62
High-low beam .......................... 5-62
Leveling ..................................... 5-62
On reminder ............................... 5-62
Hood Release .................................... 3-49
Horn .................................................. 5-71
I
Ignition
Keys ........................................... 3-26
Switch .......................................... 5-2
Illuminated Entry System ................. 6-97
Immobilizer System
(with Advanced Key) ........................ 3-53
Immobilizer System
(without Advanced Key) ................... 3-57
Indicator Lights ................................. 5-41 AFS OFF .................................... 5-55
Cruise ......................................... 5-55
DSC OFF .................................... 5-55
Headlight high-beam .................. 5-54
KEY ............................................ 5-52
Low engine coolant
temperature ................................ 5-54
Power steering malfunction ........ 5-56
Security ...................................... 5-53
Shift position .............................. 5-54
TCS/DSC ................................... 5-54
Turn signal/hazard warning ........ 5-56
Information Display .......................... 6-99
Audio display ........................... 6-100
Climate control display ............ 6-100
Clock ........................................ 6-100
Information display functions .... 6-99
Outside temperature display ..... 6-100
11-4
Index
Mazda3_8BM5-EA-10F_Edition3 Page510
Tuesday, October 5 2010 9:8 AM
Form No.8BM5-EA-10F