length MAZDA MODEL 3 5-DOOR 2004 Owners Manual

2-11
Essential Safety Equipment
Seat Belt Systems
Form No. 8S18-EA-03I

Emergency Locking Mode
If the belt has fully retracted, it will always be in the emergency locking mode until you
move it into automatic locking mode by pulling the belt all the way out to its full length. In
the emergency locking mode, the belt remains comfortable on the occupant and the
retractor will lock in position during a collision.
If the belt feels tight and hinders comfortable movement while the vehicle is stopped or in
motion, you may be in the automatic locking mode because you have pulled the belt too far
out. To return to the more comfortable emergency locking mode, wait until you can stop
the vehicle in a safe level area, retract the belt fully to convert it back to emergency locking
mode and then again extend it around you.

Automatic Locking Mode
Always use the automatic locking mode to keep the child-restraint system from shifting to
an unsafe position in the event of an accident. To get the seat belt into the automatic
locking mode, pull it all the way out and connect it as instructed on the child-restraint
system. It will retract down to the child-restraint system and stay locked on it. See the
section on child restraint (page 2-21).
J48C_8S18-EA-03I_Edition3.book Page 11 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

2-18
Essential Safety Equipment
Seat Belt Systems
Form No. 8S18-EA-03I

Fastening the Lap Portion of the
Seat Belt
Grasp tongue (A) and insert it into the
anchor buckle (B) until you hear a click. It
is now secure for passenger use. If your seat belt is not long enough, even
when fully extended, a seat belt extender
may be available to you at no charge from
your Authorized Mazda Dealer.
This extender will be only for you and for
the particular vehicle and seat. Even if it
plugs into other seat belts, it may not hold
in the critical moment of a crash.
When ordering an extender, only order
one that provides the necessary additional
length to fasten the seat belt properly.
Please contact your Authorized Mazda
Dealer for more information.
NOTE
To encourage rear seat passengers to
wear their seat belts, we suggest
leaving the rear center lap position of
the belt fastened at all times except
when folding the rear seat forward.
NOTE
After returning the rear-left seatback to
its upright position, fasten the lap
portion of the belt.
Seat Belt Extender
Unnecessary Use of an Extender:
Using a seat belt extender when not
necessary is dangerous. The seat belt
will be too long and not fit properly.
In an accident, the seat belt will not
provide adequate protection and you
could be seriously injured. Only use
the extender when it is required to
fasten the seat belt properly.
Using an Improper Extender:
Using a seat belt extender that is for
another person or a different vehicle
or seat is dangerous. The seat belt will
not provide adequate protection and
the user could be seriously injured in
an accident. Only use the extender
provided for you and for the
particular vehicle and seat. NEVER
use the extender in a different vehicle
or seat.
WARNING
J48C_8S18-EA-03I_Edition3.book Page 18 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

2-19
Essential Safety Equipment
Seat Belt Systems
Form No. 8S18-EA-03I
The seat belt warning light illuminates
and a beep sound will be heard if the
driver’s seat belt is not fastened when the
ignition switch is turned to the ON
position.
Conditions of operation
Using an Extender That is Too Long:
Using an extender that is too long is
dangerous. The seat belt will not fit
properly. In an accident, the seat belt
will not provide adequate protection
and you could be seriously injured.
Don ’t use the extender or choose one
shorter in length if the distance
between the extender ’s buckle and the
center of the user ’s body is less than
15cm (6 in).
NOTE
When not in use, remove the seat belt
extender and store it in the vehicle. If
the seat belt extender is left connected,
the seat belt warning light will not
illuminate and function properly.
WARNINGSeat Belt Warning Light/
Beep
Condition Result

The driver ’s seat belt is
not fastened when the
ignition switch is turned
to the ON position. The warning light
illuminates for about
1 minute and a beep
sound will be heard
for about 6 seconds.
The driver ’s seat belt is
fastened while the
warning light and the
beep are activated. The warning light
turns off and the
beep sound stops.
The driver ’s seat belt is
fastened before the
ignition switch is turned
to the ON position. The warning light
will not illuminate
and the beep sound
will not be heard.
J48C_8S18-EA-03I_Edition3.book Page 19 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

2-26
Essential Safety Equipment
Child Restraint
Form No. 8S18-EA-03I
3. To get the retractor into the automatic locking mode, pull the shoulder belt
portion of the seat belt until the entire
length of the belt is out of the retractor.
4. Push the child-restraint system firmly into the vehicle seat. Be sure the belt
retracts as snugly as possible. Clicking
from the retractor will be heard during
retraction if the system is in the
automatic locking mode. If the belt
does not lock the seat down tight,
repeat this step. 5. If your child-restraint system requires
the use of a tether strap, hook and
tighten the tether strap by following the
manufacturer ’s instructions.NOTE
Inspect this function before each use of
the child-restraint system. You should
not be able to pull the shoulder belt out
of the retractor while the system is in
the automatic locking mode. When
you remove the child-restraint system,
be sure the belt fully retracts to return
the system to emergency locking mode
before occupants use the seat belts.
Cover
For rear right seat For rear left seat
Anchor
bracket
4 Door
Anchor bracket
location
For rear center seat
Anchor
bracket
Tether
strap4 Door
Tether strap
position
J48C_8S18-EA-03I_Edition3.book Page 26 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

2-29
Essential Safety Equipment
Child Restraint
Form No. 8S18-EA-03I

Front Passenger
’s Seat Child-
Restraint System Installation
1. Slide the seat as far back as possible.
2. Secure the child-restraint system with
the lap portion of the lap/shoulder belt.
See the manufacturer ’s instructions on
the child-restraint system for belt
routing instructions.
3. To get the retractor into the automatic locking mode, pull the shoulder belt
portion of the seat belt until the entire
length of the belt is out of the retractor.
4. Push the child-restraint system firmly into the vehicle seat. Be sure the belt
retracts as snugly as possible. Clicking
from the retractor will be heard during
retraction if the system is in automatic
locking mode. If the belt does not lock
the seat down tight, repeat the previous
step and also this one.Children and Seating Position with
Side and Curtain Air Bags:
Allowing anyone to lean over or
against the front door, the area of
front seat, front and rear window
pillars and the roof edge along both
sides which the side and curtain air
bags deploy even though using a
child-restraint system is dangerous. If
the vehicle is equipped with side and
curtain air bags, the impact of
inflation could cause serious injury
or death to the child. Furthermore,
leaning over or against the front door
could block the side and curtain air
bags and eliminate the advantages of
supplemental protection. With the
front air bag and the additional side
air bag that comes out of the front
seat, the rear seat is always a better
location for children. Do not allow a
child to lean over or against the
doors, even if the child is seated in a
child-restraint system.
WARNING
J48C_8S18-EA-03I_Edition3.book Page 29 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

3-29
Knowing Your Mazda
Form No. 8S18-EA-03I
Steering Wheel and Mirrors

Steering Wheel Adjustment
To change the angle or length of the
steering wheel:
1. Stop the vehicle, pull down the lock
release lever under the steering
column.
2. Tilt the steering wheel and/or adjust the steering column length to the desired
positions, push the lever up to lock the
column.
3. Push the wheel up and down to be certain it ’s locked before driving.

Outside Mirrors
Check the mirrors
’ angles before driving.
Manual control mirror
To adjust, move the mirror ’s control lever,
just inside the door.
Steering Wheel
Adjusting the Steering Wheel:
Adjusting the steering wheel while the
vehicle is moving is dangerous.
Moving it can very easily cause the
driver to abruptly turn to the left or
right. This can lead to loss of control
or an accident. Never adjust the
steering wheel while the vehicle is
moving.
WARNING
Lock release lever
Mirrors
Convex Mirror (Passenger Side):
Changing lanes without taking into
account the actual distance of the
vehicle in the convex mirror is
dangerous. You could have a serious
accident. What you see in the convex
mirror is closer than it appears. Be
sure to look over your shoulder before
changing lanes.
WARNING
Control lever
J48C_8S18-EA-03I_Edition3.book Page 29 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

10-5
Specifications
Form No. 8S18-EA-03I

Capacities
(Approximate Quantities)

Check oil and fluid levels with dipsticks or reservoir gauges.

Dimensions
* With side protector
Item Unit
L US qt Imp qt
Engine oil With oil filter replacement
4.34.5 3.8
Without oil filter replacement 3.94.1 3.4
Coolant With heater
7.57.9 6.6
Without heater 6.97.3 6.1
Manual transaxle oil 2.87 3.03 2.53
Automatic transaxle fluid 7.27.6 6.3
Fuel tank 5514.5
(US gal) 12.1
(Imp gal)
Item Model
4 Door 5 Door
Overall length (STD)
4,530 mm (178.3 in) —
(SAP) 4,540 mm (178.7 in) 4,485 mm (176.6 in)
Overall width
*1,755 mm (69.1 in) 1,755 mm (69.1 in)
Overall height 1,465 mm (57.7 in)1,465 mm (57.7 in)
Front tread 1,530 mm (60.2 in)1,530 mm (60.2 in)
Rear tread 1,515 mm (59.6 in)1,515 mm (59.6 in)
Wheelbase 2,640 mm (103.9 in) 2,640 mm (103.9 in)
J48C_8S18-EA-03I_Edition3.book Page 5 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

Contents,\bAccessor\fes\a,\band\bLaser\b\b\b\b
Before U\be
Accessor\fes
Please\bcontact\ban\bAutho\ar\fzed\bMazda\bDealer\b\ff\by\aou\bare\bm\fss\fng\bany\bof\bthe\bfol\alow\fng\baccessor\fes.
Map\bD\fsc
Owner's\bManual
CAUT\fON:
TH\fS PRODUCT \fS A CLAS\OS LASER PRODUCT \O.I
HOWEVER TH\fS PRODUCT\O USES A V\fS\fBLE/\fNV\fS\O\fBLE LASER BEAM
WH\fCH COULD CAUSE HAZA\ORDOUS RAD\fAT\fON EXPOSU\ORE \fF D\fRECTED.
BE SURE TO OPERATE T\OH\fS PRODUCT CORRECTLY\O AS \fNSTRUCTED.
USE OF CONTROLS OR AD\OJUSTMENTS OR PERFORM\OANCE OF
PROCEDURES OTHER THA\ON THOSE SPEC\fF\fED HE\ORE\fN MAY RESULT \fN
HAZARDOUS RAD\fAT\fON EX\OPOSURE. DO NOT OPEN \OCOVERS AND DO
NOT REPA\fR YOURSELF.\O REFER SERV\fC\fNG TO QU\OAL\fF\fED PERSONNEL.
2
La\ber product\b:
Wave\blength:\b650\bnm
Laser\bpower:\bNo\bhazardo\aus\brad\fat\fon\b\fs\bem\ftted\a\bw\fth\bsafety\bprotect\fo\an.
Prepa-
ration
\fmme-
diate
use
Advanced
use
\ff
necessary
Marked\bPo\fnt
Direct De
After Rou
Route Ch
\b\b\bProd
Setup
Precaut\fons/S
Troubleshoot
Ma\fntenance
De\btin
Charac
PO\f \fco
Accessor\fes\bLaser\bProduc
Contents\b.\b.\b.\bSafety\bInform
Introduct\fon\bNames\band\bF
Before U