reset MAZDA MODEL 3 5-DOOR 2004 Owners Manual
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2004, Model line: MODEL 3 5-DOOR, Model: MAZDA MODEL 3 5-DOOR 2004Pages: 372, PDF Size: 8.19 MB
Page 71 of 372
3-3
Knowing Your Mazda
Doors and Locks
Form No. 8S18-EA-03I
This system locks and unlocks the doors
and the liftgate.
It can also help you signal for attention in
an emergency.
Press the button slowly and accurately.
Keyless Entry System*
To avoid damage to the transmitter, do
not:
•Drop it.
• Get it wet.
• Disassemble it.
• Expose it to heat or sunlight.
CAUTION
NOTE
•The keyless entry system is
designed to operate up to about 2.5
m (8 ft) from the center of the
vehicle, but this may vary because
of local conditions.
• The system doesn
’t operate when
the key is in the ignition switch.
• Doors cannot be locked by pressing
the LOCK button while any other
door is open. The hazard warning
lights will also not flash.
• If the transmitter does not operate
when pressing a button or the
operation range becomes too small,
the battery may be dead. To install a
new battery, refer to Maintenance
(page 3-5).
• Additional transmitters can be
obtained at an Authorized Mazda
Dealer. Up to 3 transmitters can be
used with the keyless entry system
per vehicle. Bring all transmitters to
an Authorized Mazda Dealer when
the electronic codes need to be
reset.
*Some models.
J48C_8S18-EA-03I_Edition3.book Page 3 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI
Page 94 of 372
3-26
Knowing Your Mazda
Security System
Form No. 8S18-EA-03I
Maintenance
If you have a problem with the
immobilizer system or the key, consult an
Authorized Mazda Dealer.
Modification and Add-On
Equipment
Mazda cannot guarantee the immobilizer
system
’s operation if the system has been
modified or if any add-on equipment has
been installed to it.
NOTE
• If the security indicator light comes
on and stays on when the ignition
switch is turned to the ON position,
the engine will not start.
• Signals from a TV or radio station,
or from a transceiver or a mobile
telephone, could interfere with your
immobilizer system. If you are
using the proper key and your
engine fails to start, check the
security indicator light. If it is
flashing, remove the ignition key
and wait 2 seconds or more, then
reinsert it and try starting the engine
again. If it doesn
’t start after 3 or
more tries, contact an Authorized
Mazda Dealer.
• If the security indicator light flashes
continuously while you are driving,
don’
t shut off the engine. Go to an
Authorized Mazda Dealer and have
it checked. If you shut off the
engine while the light is flashing
you won ’t be able to restart it.
• Since the electronic codes are reset
when repairing the immobilizer
system, the keys are needed. Bring
all the existing keys to the
Authorized Mazda Dealer.
NOTE
•The keys carry a unique electronic
code. For this reason, and to assure
your safety, obtaining replacement
key requires some waiting time.
They are only available through an
Authorized Mazda Dealer.
• Always keep a spare key, in case
one is lost. If a key is lost, contact
an Authorized Mazda Dealer as
soon as possible.
• If you lose a key, an Authorized
Mazda Dealer will reset the
electronic codes of your remaining
keys and immobilizer system. Bring
all the remaining keys to the
Authorized Mazda Dealer to reset.
Starting the vehicle with a key that
has not been reset is not possible.
To avoid damage to your vehicle, do
not modify the system or install any
add-on equipment to it.
CAUTION
J48C_8S18-EA-03I_Edition3.book Page 26 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI
Page 135 of 372
5-21
Driving Your Mazda
Starting and Driving
Form No. 8S18-EA-03I
To Resume Cruising Speed at
More Than 30 km/h (19 mph)
If some other method besides the ON/
OFF switch was used to cancel cruising
speed and the system is still activated, the
most recent set speed will automatically
resume when the RES/ACCEL button is
pressed.
If vehicle speed is below 30 km/h (19
mph), increase the vehicle speed up to 30
km/h (19 mph) and press the RES/
ACCEL button.
To Cancel
To turn off the system, use one
of these
methods:
• Press the ON/OFF switch.
• Slightly depress the brake pedal.
• Depress the clutch pedal. (Manual
transaxle only)
• Press the CANCEL button.
The system is off when the ignition is off.
NOTE
Cruise control will cancel at about 15
km/h (9 mph) below the preset speed
or below 30 km/h (19 mph).
J48C_8S18-EA-03I_Edition3.book Page 21 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI
Page 141 of 372
5-27
Driving Your Mazda
Instrument Cluster and Indicators
Form No. 8S18-EA-03I
Speedometer
The speedometer indicates the speed of
the vehicle.
Odometer, Trip Meter and Trip
Meter Selector
The display mode can be changed
between trip meter A and trip meter B by
pressing the selector while one of them is
displayed. The selected mode will be
displayed.
Odometer
The odometer records the total distance
the vehicle has been driven.
Selector
Trip meter
Odometer
Odometer
Odometer Trip meter A
Press the selector
Press the selector
Trip meter B
NOTE
•
(Standard meter)
The odometer and trip meter can be
displayed as follows even when the
ignition switch is in the ACC or
LOCK position.
Displays for 10 minutes after the
ignition switch is turned to the
ACC or LOCK position from the
ON position.
Displays for 10 minutes after the
driver’ s door is opened.
• (Black-out meter)
When the ignition switch is in the
ACC or LOCK position, the
odometer or trip meters cannot be
displayed, however, pressing the
selector button can inadvertently
switch the trip meters or reset them
during an approximate ten-minute
period in the following cases:
After the ignition switch is
turned to the ACC or LOCK
position from the ON position.
After the driver ’s door is opened.
J48C_8S18-EA-03I_Edition3.book Page 27 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI
Page 142 of 372
5-28
Driving Your Mazda
Instrument Cluster and Indicators
Form No. 8S18-EA-03I
Tr i p m e t e r
The trip meter can record the total
distance of two trips. One is recorded in
trip meter A, and the other is recorded in
trip meter B.
For instance, trip meter A can record the
distance from the point of origin, and trip
meter B can record the distance from
where the fuel tank is filled.
When trip meter A is selected, pressing
the selector again within one second will
change to trip meter B mode.
When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.
The trip meter records the total distance
the vehicle is driven until the meter is
again reset. Return it to "0.0" by holding
the selector depressed for more than 1
second. Use this meter to measure trip
distances and to compute fuel
consumption.
Tachometer
The tachometer shows engine speed in
thousands of revolutions per minute
(rpm).
NOTE
• Only the trip meters record tenths of
kilometers (miles).
• The trip record will be erased when:
The power supply is interrupted
(blown fuse or the battery is
disconnected).
The vehicle is driven over 999.9
km (mile).
Don ’t run the engine with the
tachometer needle in the RED ZONE.
This may cause severe engine damage.
Red zone
CAUTION
J48C_8S18-EA-03I_Edition3.book Page 28 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI
Page 187 of 372
6-19
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I
2. Turn the audio control dial to adjust the selected functions as follows: Automatic Level Control (ALC)
The automatic level control is a feature
that automatically adjusts audio volume
and sound quality according to the vehicle
speed.
The volume increases in accordance with
the increase in vehicle speed, and
decreases as vehicle speed decreases.
The following four modes are available.
Select the desired mode.
Turn the audio control dial to select the
ALC OFF, ALC LEVEL1
—3 mode. The
selected mode will be indicated.
BEEP setting
The beep-sound when operating the audio
system can be set on or off.
ILLM EFT setting (Illumination setting
during operation)
The audio system illumination during
operation can be set on or off.
Indication Turn Left Turn Right
Select
modeSelect
mode
Decrease
bass Increase
bass
Decrease
mid-
range Increase
mid-range
Decrease
treble Increase
treble
Shift the
sound
to the
front Shift the
sound
to the rear
Shift the
sound
to the left Shift the
sound
to the right
OFF ON
OFF ON
NOTE
About 5 seconds after selecting any
mode, the volume function will be
automatically selected. To reset bass,
mid-range, treble, fade, and balance,
press the audio control dial for 2
seconds. The unit will beep and
"CLEAR" will be displayed.
Mode Vo l u m e
change
No change
Minimum
Medium
Maximum
J48C_8S18-EA-03I_Edition3.book Page 19 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI
Page 188 of 372
6-20
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I
Operating the Radio
Radio ON
Press a band selector button ( , )
to turn the radio on.
Band selection
Choose AM by pressing the AM button
( ) and FM by pressing the FM1/2
button ( ).
The selected mode will be indicated. If
FM stereo is being received, "ST" will be
displayed. Tu n i n g
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
Manual tuning
Turning the manual tuning dial will
change the frequency higher or lower.
Manual tuning dial/
Auto memory button
Channel
preset
buttons
Scan button
Band selector buttons
Seek
tuning
buttons
NOTE
If the FM broadcast signal becomes
weak, reception automatically changes
from STEREO to MONO for reduced
noise, and the "ST" indicator will go
out.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
J48C_8S18-EA-03I_Edition3.book Page 20 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI
Page 189 of 372
6-21
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I
Seek tuning
Pressing the seek tuning button ( , )
will cause the tuner to seek a higher or
lower frequency automatically.
Scan tuning
Press the scan button ( ) to
automatically sample strong stations.
Scanning stops at each station for about 5
seconds. To hold a station, press the scan
button ( ) again during this interval.
Preset channel tuning
The 6 preset channels can be used to store
6 AM and 12 FM stations.
1. To set a channel first select AM, FM1, or FM2. Tune to the desired station.
2. Depress a channel preset button for about 2 seconds until a beep is heard.
The preset channel number and station
frequency will be displayed. The
station is now held in the memory.
3. Repeat this operation for the other stations and bands you want to store.
To tune one in the memory, select AM,
FM1, or FM2 and then press its
channel preset button. The station
frequency and the channel number will
be displayed. Auto memory tuning
This is especially useful when driving in
an area where the local stations are not
known. Additional AM/FM stations can
be stored without disturbing the
previously set channels.
Press and hold the auto memory button
( ) for about 2 seconds until a beep
is heard; the system will automatically
scan and temporarily store up to 6 stations
with the strongest frequencies in each
selected band in that area.
After scanning is completed, the station
with the strongest frequency will be tuned
and its frequency displayed.
Press and release the auto memory button
( ) to recall stations from the auto-
stored stations. One stored station will be
selected each time; its frequency and
channel number will be displayed.
NOTE
If you continue to press and hold the
button, the frequency will continue
changing without stopping.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
NOTE
If no stations can be tuned after
scanning operations, "A" will be
displayed.
J48C_8S18-EA-03I_Edition3.book Page 21 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI
Page 196 of 372
6-28
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I
Operating the In-Dash CD Changer*
Inserting the CD
The CD must be label-side up when
inserting. The auto-loading mechanism
will set the CD and begin play. There will
be a short lapse before play begins while
the player reads the digital signals on the
CD.
The disc number and the track number
will be displayed. Normal insertion
1. Press the load button ( ).
2. When "IN" is displayed, insert the CD.
Inserting CDs into desired tray number
1. Press and hold the load button ( )
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the desired tray number within 3 seconds
after the beep is heard.
3. When "IN" is displayed, insert the CD.
CD slot CD play button CD eject button
Load buttonRepeat button
Scan button
Track up
button
Track down
button
Reverse button Fast-forward button
Random button
Disc up
button
Disc down
button
Display button
NOTE
A CD cannot be inserted while the
display reads "WAIT". A beeping
sound can be heard during this waiting
time. Simultaneously pressing the
power/volume dial and the load button
( ) for about 2 seconds will turn
this beeping sound ON or OFF.
NOTE
The CD cannot be inserted to the
desired tray number if the number is
already occupied.
*Some models.
J48C_8S18-EA-03I_Edition3.book Page 28 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI
Page 197 of 372
6-29
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I
Multiple insertion
1. Press and hold the load button ( ) for about 2 seconds until a beep is
heard.
2. Wait 3 seconds or press the load button ( ) again within 3 seconds after the
beep is heard.
3. When "IN" is displayed, insert the CD.
4. When "IN" is displayed again, insert the next CD.
Displaying the CD-inserted tray
number
When you want to know the number for a
CD-inserted tray, press the display button
( ).The tray number will be displayed
for 5 seconds.
Ejecting the CD
Normal ejection
1. Press the CD eject button ( ). The disc number and "DISC" "OUT" will
be displayed.
2. Pull out the CD. Ejecting CDs from desired tray number
1. Press and hold the CD eject button ( )
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the desired CD number within 3 seconds
after the beep is heard.
3. Pull out the CD.
Multiple ejection
1. Press and hold the CD eject button ( ) for about 2 seconds until a beep is
heard.
2. Wait 3 seconds or press the CD eject button ( ) again within 3 seconds
after the beep is heard.
3. Pull out the CD, then the next CD will be ejected.
Playing
Press the CD play button ( ) to start
play when a CD is in the unit.
If there isn ’t a CD in the unit when the CD
play button ( ) is pressed, "NO DISC"
will flash on and off.
NOTE
The first-inserted CD will be played
automatically when:
• No other CD is inserted within 15
seconds after "IN" is displayed.
• The CD trays are full.
NOTE
When the CD is ejected during play,
the next CD will be played
automatically.
NOTE
•CDs will be ejected starting with the
one with the lowest number.
• All CDs in the tray will be ejected
continuously.
• CDs can be ejected when the
ignition switch is off. Press and hold
the CD eject button ( ) for about 2
seconds and all CDs will eject.
J48C_8S18-EA-03I_Edition3.book Page 29 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI