turn signal bulb MAZDA MODEL 3 5-DOOR 2004 Owners Manual

5-42
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
Form No. 8S18-EA-03I

Turn-Signal/Hazard Warning
Indicator Lights
When operating the turn-signal lights, the
left or right turn-signal indicator light
flashes to indicate which turn-signal light
is operating (page 5-47).
When operating the hazard warning
lights, both turn-signal indicator lights
flash (page 5-53).

Air Bag/Front Seat Belt
Pretensioner System Warning
Beep
If a malfunction is detected in the air bag/
front seat belt pretensioner systems and
the warning light, a warning beep sound
will be heard for about 5 seconds every
minute.
The air bag and seat belt pretensioner
system warning beep sound will continue
to be heard for approximately 35 minutes.
Have your vehicle inspected at an Mazda
Dealer as soon as possible.
NOTE
If an indicator light remains
illuminated (does not flash) or if it
flashes abnormally, the turn signal bulb
may be burned out.
Beep Sounds
Air Bag/Front Seat Belt Pretensioner
System Warning Beep:
Driving the vehicle with the air bag/
front seat belt pretensioner system
warning beep sounding is dangerous.
In a collision, the air bags and the
front seat belt pretensioner system
will not deploy and this could result in
death or serious injury.
Do not drive the vehicle with the air
bag/front seat belt pretensioner
system warning beep sounding.
Contact an Authorized Mazda Dealer
to have the vehicle inspected as soon
as possible.
WARNING
J48C_8S18-EA-03I_Edition3.book Page 42 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

5-47
Driving Your Mazda
Switches and Controls
Form No. 8S18-EA-03I

Daytime Running Lights
(Canada)
In Canada, vehicles must be driven with
the headlights on during daytime
operation.
For that reason, the daytime running lights
automatically turn on when the ignition
switch is turned to the ON position.

Tu r n S i g n a l
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.
If the indicator light continues to flash
after a turn, manually return the lever to
its original position.
Green indicators on the dashboard show
which signal is working.
Lane-change signals
Move the lever slightly toward the
direction of the change
—until the
indicator flashes — and hold it there. It
will return to the off position when
released.
NOTE
The Daytime Running Lights turn off
when the parking brake is applied.
Turn and Lane-Change
Signals
NOTE
If an indicator light stays on without
flashing or if it flashes abnormally, the
turn signal bulb may be burned out.
Right turn
Left turn OFF
Right lane
change
Left lane
change
J48C_8S18-EA-03I_Edition3.book Page 47 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-36
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Light Bulbs
Side turn signal lightsFront turn signal lights/
Side-marker lights
Rear turn signal lightsLicense plate light
Overhead light/Map lights (Front)*
Headlights (Low beam)
Headlights
(High beam)
Fog lights* Brake lights/Taillights
Reverse light
High-mount brake light
Trunk light
4 Door
5 Door Overhead light (Rear)
Overhead light/Map lights (Front)*
Headlights (Low beam)
Headlights
(High beam)
Side turn signal lights Fog lights*
License plate light
High-mount brake light
Luggage compartment
lightOverhead light (Rear)
Rear turn signal lights
Brake lights/Taillights
Reverse light
Front turn signal lights/
Side-marker lights
*Some models.
J48C_8S18-EA-03I_Edition3.book Page 36 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-39
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
6. Replace the bulb.
7. Install the new bulb in the reverse order of removal.
Replacing a fog light bulb*
1. Turn the screw counterclockwise and remove it and partially peel back the
mudguard.
2. Turn the socket and bulb assembly counterclockwise and remove it.
Carefully remove the fog light bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket. 3. Disconnect the bulb from the electrical
connector by pressing the tab on the
connector with your finger and pulling
the bulb upward.
4. Install the new bulb in the reverse order of removal.
Front turn signal lights/Side-marker
lights
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
NOTE
• To replace the bulb, contact an
Authorized Mazda Dealer.
• Use the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
• When reinstalling the sealing cover,
make sure faces up.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Socket
Ta b
*Some models.
J48C_8S18-EA-03I_Edition3.book Page 39 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-40
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Side turn signal lights
1. Slide the unit as shown in the figure to remove it.
2. Detach the electrical connector from the unit by pulling it to the rear.
3. Install the new side turn signal unit in the reverse order of removal. Brake lights/Taillights, Rear turn signal lights (4 Door)
1. Pull the center of each plastic retainer
and remove the retainers and the trunk
end trim.
2. Pull the center of each plastic retainer and remove the retainers and partially
open the trunk side trim.
3. Turn the socket and bulb assembly counterclockwise and remove it.
NOTE
Bulb replacement is not possible
because it is built into the unit. Replace
the unit.
Removal
Installation Trunk end trim
Trunk side trim
Removal Installation
J48C_8S18-EA-03I_Edition3.book Page 40 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-41
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal. Brake lights/Taillights, Rear turn signal
lights (5 Door)
1. Remove the cover.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Socket
Brake lights/Taillights
Rear turn signal lights
Left side
Right side
Socket
Brake lights/Taillights
Rear turn signal lights
J48C_8S18-EA-03I_Edition3.book Page 41 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

10-7
Specifications
Form No. 8S18-EA-03I

Light Bulbs
Exterior light

*1 Bulb replacement is not possible because it is built into the unit. Replace the unit.
Interior light
Light bulb WattageCategory
ECE R SAE
Headlights High beam
60 HB3—
Low beam Halogen
55H7 —
Xenon fusion 35 D2S —
Front turn signal lights/Side-marker lights 27/8—#1157NA
Fog lights
*55 H11 —
Side turn signal lights*15WY5W —
High-mount brake light 18 W16W #921
Rear turn signal lights 21 W21W #7440
Brake lights/Taillights 21/5 W21/5W #7443
Reverse light 21 W21W #7440
License plate light 5 W5W—
Light bulb WattageCategory
ECE R
Trunk light (Sedan)
5W5W
Luggage compartment light (Hatchback) —
Overhead light/Map lights (Front)
*W5W
Overhead light (Rear) 10—
*Some models.
J48C_8S18-EA-03I_Edition3.book Page 7 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

11-4
Index
Form No. 8S18-EA-03I
H
Hood Release ................................... 3-20
Horn
................................................. 5-53
I
Ignition Keys
............................................ 3-2
Switch
......................................... 5-2
Illuminated Entry System
................ 6-35
Immobilizer System
......................... 3-24
Indicator Lights
................................ 5-31
Cruise main
............................... 5-41
Cruise set
.................................. 5-41
Headlight high-beam
................ 5-40
power steering malfunction
...... 5-41
Security
..................................... 5-40
Shift position
............................ 5-40
Turn-signal/hazard warning
...... 5-42
Information Display
......................... 6-38
Audio display
............................ 6-39
Clock
......................................... 6-39
Information display functions
... 6-38
Inside Trunk Release Handle/
Slide Lever
....................................... 3-15
Instrument Cluster
........................... 5-26
Instrument Cluster Dimmer Select
Button
.............................................. 5-30
Interior Care
..................................... 8-57
Interior Lights
.................................. 6-35
J
Jump-Starting ................................... 7-16
K
Keyless Entry System ........................ 3-3
Keys
................................................... 3-2
L
Label Information ............................ 10-2
Lane-Change Signals
....................... 5-47
Liftgate
............................................. 3-10
Luggage compartment
.............. 3-11
Light Bulbs Replacement
.............................. 8-36
Specifications
............................ 10-7
Lighter
.............................................. 6-40
Lighting Control
............................... 5-44
Lubricant Quality
............................. 10-4
Luggage Compartment Light
........... 6-37
M
Maintenance Introduction
................................. 8-2
Owner maintenance
precautions
................................ 8-11
Owner maintenance schedule
... 8-10
Scheduled
.................................... 8-3
Manual Transaxle Operation
.............. 5-9
Recommendations for
shifting
...................................... 5-10
Map Lights
....................................... 6-37
Meters and Gauges
........................... 5-26
Mirrors Outside mirrors
......................... 3-29
Rearview mirror
........................ 3-31
Money-Saving Suggestions
................ 4-7
Moonroof
......................................... 3-21
O
Odometer and Trip Meter ................ 5-27
Outside Mirrors
................................ 3-29
Overhead Lights
............................... 6-36
Overheating
...................................... 7-13
Overloading
...................................... 4-12
J48C_8S18-EA-03I_Edition3.book Page 4 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI