change time MAZDA MODEL 3 5-DOOR 2015 Owner's Guide

5–96
Interior Features
Bluetooth®
Deleting all devices
1. Select the
icon on the home screen
and display the Settings screen.
2. Select the
tab.
3. Select
.
4. Select
.
5. Select
.
6. Select
.
Changing PIN code
PIN code (4 digits) can be changed.
1. Select the
icon on the home screen
and display the Settings screen.
2. Select the
tab.
3. Select
.
4. Select
.
5. Select
.
6. Input the new PIN code to be set.
7. Select
.
Available Language (Type B)
The Bluetooth ® Hands-Free System
applies to the following languages:
 y  English y Spanish y French
Refer to Settings on page 5-55 .
Voice Recognition (Type B)
In this section, the basic operation of the
voice recognition is explained.
Activating Voice Recognition
Press the talk button.
Ending Voice Recognition
Use one of the following methods:
 y  Press the hang-up button. y Say, “Cancel”. y Operate the commander switch or the
center display (only when vehicle is
stopped).
Skipping Voice Guidance (for faster
operation)
Press and release the talk button.
Troubleshooting for Voice Recognition
If you do not understand an operation
method while in the voice recognition
mode, say “Tutorial” or “Help”.
Commands useable anytime during
voice recognition
“Go Back” and “Cancel” are commands
which can be used at anytime during voice
recognition.
Returning to previous operation
To return to the previous operation, say,
“Go Back” while in voice recognition
mode.
Cancel
To put the Bluetooth
® Hands-Free system
in standby mode, say, “Cancel” while in
voice recognition mode.
.B[EB@%9&"'@&EJUJPOJOEC


.B[EB@%9&"'@&EJUJPOJOEC










6–6
Maintenance and Care
Scheduled Maintenance
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fi ll up, or replace if necessary.
T: Tighten
Remarks:
*1 The engine oil and fi lter must be changed at least once a year or within 16,000km (10,000 mi\
les) since last
engine oil and fi lter change. The system must be reset whenever replacing the engine oil regardless of\
the
message/wrench indicator light display.
*2 Use FL22 type coolant in vehicles with the inscription “FL22” on t\
he radiator cap itself or the surrounding area. Use FL22 when replacing the coolant.
*3 According to state/provincial and federal regulations, failure to perfor\
m maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or mileage/kilometer period to ensure long-term reliabi\
lity.
.B[EB@%9&"'@&EJUJPOJOEC


.B[EB@%9&"'@&EJUJPOJOEC










6–10
Maintenance and Care
Scheduled Maintenance
Maintenance Interval Number of months or kilometers (miles), whichever comes fi
rst.
Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 km 8 16 24 32 40 48 56 64 72 80 88 96
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Exhaust system and heat shields Inspect every 72,000 km (45,000 miles) or 5 years.
All locks and hinges L L L L L L L L L L L L
Washer fl uid level I I I I I I I I I I I I
AIR CONDITIONER SYSTEM
Cabin air fi lter Replace every 40,000 km (25,000 miles) or 2 years.
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fi ll up, or replace if necessary.
R: Replace
L: Lubricate
T: Tighten
Remarks:
*1 Engine oil fl exible maintenance is available for U.S.A. and Puerto Rico residents who\
se vehicle is operated
mainly where none of the following conditions apply.
y Extended periods of idling or low-speed operation such as police car, taxi or driving school cary Driving in dusty conditions
If any do apply, follow fi xed maintenance.
The engine oil and fi lter must be changed at least once a year or within 16,000 km (10,000 m\
iles) since last
engine oil and fi lter change. The system must be reset whenever replacing the engine oil regardless of\
the
message/wrench indicator light display.
*2 Use FL22 type coolant in vehicles with the inscription “FL22” on t\
he radiator cap itself or the surrounding area. Use FL22 when replacing the coolant.
*3 According to state/provincial and federal regulations, failure to perfor\
m maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or mileage/kilometer period to ensure long-term reliabi\
lity.
.B[EB@%9&"'@&EJUJPOJOEC


.B[EB@%9&"'@&EJUJPOJOEC










6–20
Maintenance and Care
Scheduled Maintenance
Maintenance Monitor
Maintenance Monitor (Type A audio)
“Oil Change” with a fl exible setting *1 is available. Consult your Authorized Mazda Dealer
when you want to change the setting *2 . Once the system turns on, the wrench indicator light
in the instrument cluster will be illuminated when remaining oil life be\
comes less than 500
km (300 mile), or remaining days are less than 15 (whichever comes fi\
rst).
Reset method
Press and hold the TRIP button with the ignition switched off, then switch it on. Keep
pressing the TRIP button for more than 5 seconds. The master warning light will fl ash for a
few seconds when the reset is completed.
*1 The fl exible setting is available in the United States and Puerto Rico. Based \
on the
engine operating conditions, the onboard computer in your vehicle calcul\
ates the
remaining oil life. Mazda Genuine 0W-20 oil and Castrol
® 0W-20 oil are required to
achieve optimum calculation performance.
*2 Once the Flexible Oil Maintenance Setting is selected, the system must b\
e reset whenever replacing the engine oil.
Maintenance Monitor (Type B audio)
1. Select the icon on the home screen to display the “Applications” screen.
2. Select the “Maintenance” to display the maintenance list screen.
3. Switch the tab and select the setting item you want to change.
You can customize settings in the setup display as follows:
Tab Item Explanation
Maintenance Setting
Notifi cation can be switched on/off.
Time (months) Displays the time or distance until maintenance is due. Select this item to set the maintenance period.
“Scheduled Due!” is displayed in red and the wrench indicator
light in the instrument cluster will be illuminated when the
remaining distance is less than 500 km or 250 mile, or the
remaining number of days is less than 15 (whichever comes
fi rst).
Distance (mile or km)
Reset
Resets the time and distance to the initial values.
Once the system turns on, it needs to be reset whenever
carrying out maintenance.
.B[EB@%9&"'@&EJUJPOJOEC


.B[EB@%9&"'@&EJUJPOJOEC










6–32
Maintenance and Care
Owner Maintenance
Inspect fl uid level in the washer fl uid
reservoir; add fl uid if necessary.
L
Use plain water if washer fl uid is
unavailable.
But use only washer fl uid in cold weather
to prevent it from freezing.
NOTE
Front and rear washer fl uid is supplied
from the same reservoir.
Body Lubrication
All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the hood's secondary latch
keeps the hood from opening when the
primary latch is released.
.B[EB@%9&"'@&EJUJPOJOEC


.B[EB@%9&"'@&EJUJPOJOEC










7–35
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Warning Sound is
Activated
Lights-On Reminder
The lights-on reminder is operable when
the time setting *1 of the auto headlight off
function is off.
If lights are on and the ignition is switched
to ACC or the ignition is switched off, a
continuous beep sound will be heard when
the driver's door is opened.
*1 If the light switch is left on, the auto headlight off function automatically
turns off the lights about 30 seconds
after switching the ignition off. The
time setting can be changed.
Refer to Personalization Features on page 9-12 .
NOTE
 y When the ignition is switched to ACC,
the “Ignition Not Switched Off (STOP)
Warning Beep” (page 7-36 ) overrides
the lights-on reminder.
 y A personalized function is available to
change the sound volume for the lights-
on reminder.
 Refer to Personalization Features on page 9-12 .
Air Bag/Front Seat Belt Pretensioner System Warning
Beep
If there is a problem with the air bag/seat
belt pretensioner systems and the warning
light illumination, a warning beep sound
will be heard for about 5 seconds every
minute.
The air bag and seat belt pretensioner
system warning beep sound will continue
to be heard for approximately 35
minutes. Have your vehicle inspected at
an Authorized Mazda Dealer as soon as
possible.
WARNING
Do not drive the vehicle with the air
bag/seat belt pretensioner system
warning beep sounding:
Driving the vehicle with the air bag/
seat belt pretensioner system warning
beep sounding is dangerous. In a
collision, the air bags and the seat belt
pretensioner system will not deploy
and this could result in death or serious
injury. Contact an Authorized Mazda
Dealer to have the vehicle inspected as
soon as possible.
.B[EB@%9&"'@&EJUJPOJOEC


.B[EB@%9&"'@&EJUJPOJOEC










8–45
Customer Information and Reporting Safety Defects
Declaration of Conformity
NOTE
During printing time of this user manual the approvals listed above are granted.
WARNING
Change or modifi cations not expressively approved by the party responsible for
compliance could void the use's authority to operate the equipment.
HomeLink Wireless Control System
CAUTION
HomeLink has been tested and complies with FCC and Industry Canada rules. Changes or
modifi cations not expressly approved by the party responsible for compliance could void
the user's authority to operate the device.
NOTE
FCC ID: NZLMOBHL4
CANADA:4112A-MOBHL4
This device complies with part 15 of the FCC Rules. Operation is subject\
to the following
two conditions:
1- This device may not cause harmful interference, and
2- This device must accept any interference received, including interference that may cause
undesired operation.
.B[EB@%9&"'@&EJUJPOJOEC


.B[EB@%9&"'@&EJUJPOJOEC










9–14
Specifi cations
Personalization Features
Item Feature Factory
Setting Available
Settings Settings change method
Vehicle Power door
lock
Refer to
Auto Lock/
Unlock
Function on
page 3-16 .
Changes the auto
lock/unlock function
setting for all the
doors according to
the vehicle speed,
the vehicle power
supply condition,
and the selector
lever position.
Lock: When
Driving
Unlock: IGN Off Lock: Out of
Park Unlock: In Park/ Lock:
Shifting Out of Park/
Lock: When Driving
Unlock: IGN Off/
Lock: When Driving/ Off
Refer to Settings on page 5-55 . Refer to
Auto Lock/ Unlock
Function on page 3-16 .
Keyless
entry system
Refer to
Keyless
Entry
System on
page 3-3 . The method for
unlocking the doors
using the transmitter
can be changed.
Driver's: Once,
All Doors: Twice All Doors:
Once/
Driver's:
Once, All
Doors: Twice Refer to Settings on page 5-55 . Refer to
Transmitter
on page 3-4 .
The time required
for the doors to
relock automatically
after unlocking with
the transmitter can
be changed. 60 seconds
90 seconds/
60 seconds/
30 seconds
Refer to Settings on page 5-55 . —
.B[EB@%9&"'@&EJUJPOJOEC


.B[EB@%9&"'@&EJUJPOJOEC










9–15
Specifi cations
Personalization Features
Item Feature Factory
Setting Available
Settings Settings change method
Vehicle Advanced
keyless
entry system
Refer to
Advanced
Keyless
Entry
System on
page 3-9 . The volume of the
answer-back beep
during advanced
keyless entry system
operation can be
changed.
Medium
High/
Medium/ Low/ Off
Refer to Settings on page 5-55 .
Refer to
Locking,
Unlocking
with Request
Switch (With the advanced keyless
function) on page 3-13 .
The function to
automatically lock
the doors when
leaving the vehicle
while carrying the
key can be changed. Off On/Off
Refer to
Settings on page 5-55 . —
The method for
unlocking the doors
using the request
switch/transmitter
can be changed. Driver's: Once,
All Doors: Twice All Doors:
Once/
Driver's:
Once, All
Doors: Twice Refer to Settings on page 5-55 .
Refer to
Locking,
Unlocking
with Request
Switch (With the advanced keyless
function) on page 3-13 . Refer to
Transmitter
on page 3-4 .
The time required
for the doors to
relock automatically
after unlocking with
the request switch/
transmitter can be
changed. 60 seconds
90 seconds/
60 seconds/
30 seconds
Refer to Settings on page 5-55 . —
Illumination
entry
Refer to
Illuminated
Entry
System on
page 5-136 . The time required
for the interior
lamp to turn off
automatically can be
changed (prevents
battery depletion
when a door is open/
ajar).
30 minutes
60 minutes/
30 minutes/
10 minutes Refer to Settings on page 5-55 . —
The time required
for the interior
lamp to turn off
automatically after
all doors are closed
can be changed. 15 seconds
60 seconds/
30 seconds/
15 seconds/
7.5 seconds
Refer to Settings on page 5-55 . —
.B[EB@%9&"'@&EJUJPOJOEC


.B[EB@%9&"'@&EJUJPOJOEC










9–16
Specifi cations
Personalization Features
Item Feature Factory
Setting Available
Settings Settings change method
Vehicle Auto-wiper
control
Refer to
Windshield
Wipers and
Washer on
page 4-51 .
The auto-wiper
control function can
be changed.
On On/Off
*4 Refer to
Settings on page 5-55 . —
Daytime
running
lights
Refer to
Daytime
Running
Lights on
page 4-46 . The function of the
daytime running
lights can be
changed.
On
On/
Off — —
Auto
headlight
off
*5
Refer to
Headlights
on page
4-40 . The time required
for headlights
to turn off after
ignition is switched
off can be changed.
30 seconds 120 seconds/
90 seconds/
60 seconds/
30 seconds/ Off
*6
Refer to Settings on page 5-55 . —
Auto-light
control
Refer to
Headlights
on page
4-40 . The headlight
illumination on/
off timing based
on surrounding
lightness/darkness
can be changed.
Medium
High/
Med. High/ Medium/
Med. Low/ Low
Refer to Settings on page 5-55 . —
High Beam
Control
System
(HBC)
Refer to
High Beam
Control
System
(HBC) on
page 4-47 . The High Beam
Control System
(HBC) function can
be changed.
*1
On On/Off Refer to
Settings on page 5-55 . —
Lights-on
reminder*7
Refer to
Lights-On
Reminder
on page
7-35 . The volume of the
lights-on reminder
warning alarm can
be changed.
Off
High/Low/
Off Refer to Settings on page 5-55 . —
.B[EB@%9&"'@&EJUJPOJOEC


.B[EB@%9&"'@&EJUJPOJOEC